INNOSILICON T3H+ BTC Miner User Manual

June 6, 2024
INNOSILICON

INNOSILICON T3H+ BTC Miner User Manual
INNOSILICON T3H+ BTC Miner

Overview

Overview

Specifications
Part Number T3H+
Algorithm Sha256
Hash Rate 50TH/S (+/-5%)
Size (L×W×H) 303mm(L)203mm(W)278mm(H)
Net Weight 10.48KG
Operating Temperature 0–40 ℃ (device junction temperature)
Network Connection Ethernet

Assemble the miner

Open the package to check the miner
  • Check whether the warranty sticker is damaged, especially the one on hash boards PSU port side. If the warranty sticker is damaged when you receive the miner, please contact our after-sales personnel in time.
  • Before assembling the miner, pls shake the miner gently. Please contact our aftersales personnel immediately if there is metallic collision sound.
  • Check whether the two fans work well, if you find the fans broken please contact our after-sales personnel.
  • The wiring of the miner shall not be changed including the power cable and data cable interface as shown in the figure below
    Assemble the miner

Notes

There is an indicator on each hash board which shows the work status of the hash board. Being constantly lit means the hash board works properly.

Flickering represents overtemperature of the hash board. Please check the fans of the miner, environment temperature and the ventilation conditions.

Being off means the hash board doesn’t work. Please try to reboot the miner or change the data cable. Pls contact our after-sales team if the problem still exists.

Assemble & Operate

Connect the miner and the router by the Ethernet cable and then the miner can start to run after being powered on.

Notes: T3H+ miners consume much more power under some modes. Pls choose proper sockets.
Assemble & Operate

Normal Indicator: Being constantly lit represents static IP and flickering represents DHCP
Fault Indicator: Being on means there is something wrong with the network; Being off means it is OK.

IP SET button:

Press it for 1 to 4 seconds and the following functions can be realized:

  1. Sending the IP miner to the “Set IP” tool;
  2. Changing the miner to a Static IP within the specific range with the IPset tool

Press it for 4 to 15 seconds, the miner IP will be switched to DHCP and the pool settings will be restored to default settings.

Press it for 15 to 30 seconds to switch the Dynamic (Static) IP to Static (Dynamic).

RESET button: Press the “Reset” button to restart the miner

Operate the miner

Enter the miner console

DHCP is the default IP mode of the miner (The normal indicator of the control board now is flickering in green when the DHCP service of the router is enabled.). Find the IP via the IP scanner or the SetIP tool developed by our company. Pls refer to the official support center for the downloading address https://www.innosilicon.com/html/support_en/tool.html.

  • Save SetIP in the pc on the same network with the miner, then double click the tool and choose the language.
    Operate the miner

  • Report the miner IP
    Operate the miner
    Enter the IP of the miner in the browser and press the Enter button to go to the miner console page. Chrome is the suggested browser. (Please try with dragonadmin if the password admin is invalid.)
    Operate the miner

Configure the pool
Pls configure the pool to start mining after login.
Please use the suggested pool as below:

  1. f2pool: stratum+tcp://btc-65536.f2pool.com:3333
  2. poolin: stratum+tcp://btc-bj.ss.poolin.com:1800 or stratum+tcp://btc-sz.ss.poolin.com:1800
  3. ckpool: stratum+tcp://cn.ckpool.org:443 or stratum+tcp://pool.ckpool.org:3333
  4. btc.top: stratum+tcp://t2.btc.top:8888 or stratum+tcp://bak.t2.btc.top:3333
  5. slushpool: stratum+tcp://stratum.slushpool.com:3333
    Configure the pool
View the miner hash rate

After configuring the pool, the miner will mine for you. You can view the hash rate in the Miner Status screen.
Miner hash rate

Network configuration

Network configuration

Other pages
  • Change the operation mode
    There are 4 modes available and please click the “Save” icon after your modification.
    Operation mode

  • Overview
    Overview

  • Firmware upgrade
    Firmware upgrade

  • Modify the login password
    Login password

  • Reboot
    Reboot

  • Factory reset
    Factory reset

Innosilicon After-sales Team
Email: miner_support@innosilicon.com.cn

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals