INNOSILICON A10 Pro ETH Miner User Manual

June 6, 2024
INNOSILICON

INNOSILICON A10 Pro ETH Miner logo

INNOSILICON A10 Pro ETH Miner

INNOSILICON A10 Pro ETH Miner fig1

Overview

Specifications
Part Number A10
Algorithm Ethash
Hash Rate 500MH/s (±5%)
Size (L×W×H) 362mm(L)136mm(W)285mm(H)
 Net Weight 8.1 KG
Operating Temperature 0–40 ℃(device junction temperature)
Network Connection Ethernet

Open the package to check the miner

  • Check whether the warranty sticker is damaged, especially the one on hash boards PSU port side. If the warranty sticker is damaged when you receive the miner, please contact our after-sales personnel in time.
  • Before assembling the miner, pls shake the miner gently. Please contact our after-sales personnel immediately if there is metallic collision sound.
  • Check whether the two fans work well, if you find the fans broken please contact our after-sales personnel.
  • The wiring of the miner shall not be changed including the power cable and data cable interface as shown in the figure below.

INNOSILICON A10 Pro ETH Miner fig1

Notes: There is an indicator on each hash board which shows the work status of the hash board. Being constantly lit means the hash board works properly.

Innosilicon After-sales Team
Email:miner_support@innosilicon.com.cn

Flickering represents overtemperature of the hash board. Please check the fans of the miner, environment temperature and the ventilation conditions.
Being off means the hash board doesn’t work. Please try to reboot the miner or change the data cable. Pls contact our after-sales team if the problem still exists.

Assemble & Operation

Connect the miner and the router by the Ethernet cable. Connect each hash board with PSU with three power lines and the control board with PSU with one power line and then the miner can start to run after being powered on.
Notes: A10 miners consume much more power under some modes. Pls choose proper sockets. Don’t block the air outlet! Never place the power lines on the air outlet to avoid unnecessary damage!

INNOSILICON A10 Pro ETH Miner fig2

Normal Indicator:
Being constantly lit represents static IP and flickering represents DHCP.

Fault Indicator:
Being on means there is something wrong with the network; Being off means it is OK. IP SET button: Press it for 1 to 4 seconds and the following functions can be realized:

  1. Sending the miner IP to the “Set IP” tool;
  2. Changing the miner to a Static IP within the specific range with the IPset tool

Press it for 4 to 15 seconds, the miner IP will be switched to DHCP and the pool settings will be restored to default settings. Press it for 15 to 30 seconds to switch the Dynamic (Static) IP to Static (Dynamic) without changing pool settings.
RESET button: Press the “Reset” button to restart the miner.

Operate the miner

Enter the miner console

DHCP is the default IP mode of the miner (The normal indicator of the control board now is flickering in green when the DHCP service of the router is enabled.). Find the IP via the IP scanner or the SetIP tool developed by our company. Pls refer to the official support center for the downloading address https://[www.innosilicon.com/html/support_en/tool.html.](http://www.innosilicon.com/html/support_en/tool.html.)

a) Save SetIP in the pc on the same network with the miner, then double click the tool and choose the language.

INNOSILICON A10 Pro ETH Miner fig3

b) Report the miner IP

INNOSILICON A10 Pro ETH Miner fig4

Enter the IP of the miner in the browser and press the Enter button to go to the miner console page. Chrome is the suggested browser. (Please try with dragonadmin if the password admin is invalid.)

INNOSILICON A10 Pro ETH Miner fig5

Configure the pool

Pls configure the pool to start mining after login. Please use the suggested pool as below:
Innosilicon After-sales Team
Email:miner_support@innosilicon.com.cn

  1. f2pool:stratum+tcp://eth.f2pool.com:6688
  2. poolin: stratum+tcp://eth.ss.poolin.com:443

INNOSILICON A10 Pro ETH Miner fig6

View the miner hash rate

After configuring the pool, the miner will mine for you. You can view the hash rate in the Miner Status screen.

INNOSILICON A10 Pro ETH Miner fig7

Network configuration

INNOSILICON A10 Pro ETH Miner fig8

Other pages

Change the operation mode

There are 4 modes available and please click the “Save” icon after your modification.

INNOSILICON A10 Pro ETH Miner fig9

 Overview

INNOSILICON A10 Pro ETH Miner fig10

Firmware upgrade

INNOSILICON A10 Pro ETH Miner fig11

Modify the login password

INNOSILICON A10 Pro ETH Miner fig12

Reboot

INNOSILICON A10 Pro ETH Miner fig13

Factory reset

INNOSILICON A10 Pro ETH Miner fig14

Innosilicon After-sales Team
Email:miner_support@innosilicon.com.cn

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals