Vividia ET-078 Ultra Slim Industrial Borescope Endoscope Inspection Camera with Diameter 0.78mm Instructions

Vividia ET-078 Ultra Slim Industrial Borescope Endoscope Inspection Camera

with Diameter 0.78mm Instructions

Model: ET-078; ET-860 & ET-1060

Warning:

1. Vividia ET-78 /860/1060 has very thin and flexible probe, use with care to avoid damage due to improper use such as bending, folding and pulling.
2. Handle the ET-078/860/1060 probe slowly and carefully. Put the probe back to package case immediately after each use.
3. Carefully connect borescope probe and monitor to avoid damages to lens or make them dirty.

Vividia Technologies
Oasis Scientific Inc.

1. Vividia ET-078 / ET-860 / ET-1060 Borescope Videoscope Specs:

Videoscope Cable Camera Probe

• Resolution Pixel： 10,000
• Diameter： 0.78mm or 0.8mm or 1mm
• Length:  600mm
• Depth of Field: 2~15mm
• Field of Angle: 90°
• Light Source: Portable LED light, dimmable
• Tube material: PTFE-like plastic with optical fiber

Optical adapter for 32 times Zoom in

Monitor Display: Portable fiberscope eyepiece camera ECS-35

• 3.5” inch color LCD
• 200Mega CCD camera; Manual focus with a focus ring
• Image record resolution:1080P
• TF card, up to 32G
• Photo taking and video recording

2. What are included in package:

• Vividia ET-078 (or ET-860 or ET-1060) videoscope;
• 2 pcs rechargeable Li ion batteries;
• AC charger;
• user manual;
• heavy duty hard case.

3. How to use Vividia ET-078 / ET-860 / ET-1060 videoscope

3a. Take out flexible ultra-thin borescope carefully. The borescope probe can be broken with rough handling, be very careful to handle the thin probe. Start from eyepiece to pick up the thin probe. Do not hold the whole unit only at the thin probe part or pull thin probe tube with hard force.

3b. Install charged battery into lighting unit as below:

3c. Connect the LED lighting unit to borescope lighting receiving end. Turn on LED light by press on/off button. There are two levels of brightness by press the on/off button.

3d. Hold the whole borescope unit on the battery tube, turn on lighting by pressing battery on/off button, use another hand to guide ET fiberscope borescope flexible probe, you can observe images from eyepiece without connecting camera monitor.

3e. Clean the eyepiece lens with soft fabric or lens cleaning wipes if the lens is dirty.

3f. Recharge battery when needed.

4. How to take care Vividia ET-078 / ET-860 / ET-1060 borescope thin

probe:

• Do not pull the flexible tube too hard
• Do not press the tube and object lens with force
• Do not bend or fold or coil the flexible tube too much
• If there is difficulty to insert probe further into a object hole, do not excess force. Observe and move slowly.
• If the tube and object lens are dirty, do not clean them with finger or hand directly. Use soft fabric or lens cleaning wipe gently.
• After observation, put the ET078 probe back into the case. Do not put the whole unit left unattended on a table or bench to avoid damages.

5. Maintenance and storage ET-078 / ET-860 / ET-1060 ultra-thin borescope

probe:

• Cleaning probe tube and object lens: use clean and soft fabric to wipe probe tube gently. Use cotton Q-tip or lens cleaning wipe to clean lens carefully. Do not use excess force.
• Clean object lens, eyepiece lens and probe tube and keep them dryStore the whole unit in a dry and clean environment. Avoid excess heat, radiation and moisture
• When place ET-078 probe back into the case, put the eyepiece part back first, then place probe tube into right places.

6. Repair of Vividia ET-078 & 860 & 1060 ultra-thin borescope probe:

• Contact us immediately when image is blur, water inside probe, or probe was folded broken.

7. Use of Vividia ET videoscope portable camera monitor M35:

7a, Structure of camera monitor:
Three parts: A, Handheld monitor; B, rechargeable battery; C. ac charger

• Handheld main monitor can be used to take pictures and videos. There are LCD monitor, optical adaptor, high definition CCD sensor, control system and micro-SD storage.
• Rechargeable battery: 3.7V, 1900mAh capacity
• AC charger input, 110V – 240V, 50/60 HZ; Output: 5V and 2.4A

7b. Specs:

• 3.5” inch color LCD
• 2MP CCD camera
• Image record resolution:1080P
• Manual focus
• Optical adaptor is C-mount
• TF card, up to 32G
• Photo taking and video recording

7c. Main monitor body:

1. video recording button
2. Up button: enlarge under preview mode; under menu, up to choose different parameter
3. M for menu mode, confirm choices
4. Down button: Zoom out under preview mode; under menu, down to choose parameter
5. Picture snap button

7d: Install and connection of ET-078 borescope probe and camera

1. Open battery cover, take out battery if needed, install micro-SD card. Then put battery in.
2. Connect camera and borescope probe: Remove protective covers of optical adaptor and monitor lens. Screw them together with gentle force as below: 
3. Push Vividia ET-078 eyepiece into optical adaptor by opening optical adaptor connector with two fingers moving clamp parts close to each other. Do this slowly and carefully. Confirm the connection by turning the eyepiece lens with hand.   
4. After connection, check carefully to make sure the connection is done correctly.

7d. How to use LCD monitor camera:

• Turn on main body and monitor by press the power on/off button on the top of monitor and hold for 3 seconds. LCD monitor will go into preview mode. Do the same to turn off the unit.
• Under preview mode, adjust focus by turning the focus ring behind LCD monitor to get clear image.

• Under preview, zoom in and out by press up and down button
• Take pictures by press snap button
• Record video by press video button
• All files are saved in microSD card installed on the monitor.
• Settings can be changed by press M button.
• Battery should be taken out if the unit will not used for long time.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>