chicco 00007392100070 Advanced Steam Sterilizer with Dryer Owner’s Manual

Advanced Steam Sterilizer with Dryer
Owner’s Manual

Read all instructions BEFORE assembly and USE of productKEEP INSTRUCTIONS FOR FUTURE USE.

IMPORTANT SAFETY INSTRUCTIONS

WARNING
WHEN USING THIS ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:

BURN HAZARD
To avoid risk of burns:

• Sterilizer components and water temperaturcan be very hot. Avoid direct contact with water and steam. Handle with care.

• Do NOT touch surfaces that may be hot.
  Wait until all parts of the unit have cooled before touching them.

• During use, steam is released from the vent on top of the lid – Keep hands and face away from the vent.

• Do NOT cover the vent.

• Do NOT place Sterilizer under any object that could be damaged by steam.

• NEVER remove the lid when in use.

• It is recommended to wait before removingthe lid. Make sure to open the lid away fromyou and slowly let out any residual steam.

• Do NOT move Sterilizer when in use or when contents are still hot.

CAUTION

• NEVER use without water.
• Always measure water amount in a separate container, and pour directly into Sterilizer.
• This is NOT a toy. Keep out of reach of children.
• Adult supervision required.
• Close supervision is necessary when any appliance is used by or near children.
• For household use ONLY-Do NOT use outdoors.
• Do NOT use appliance for other than intended use.
• The use of accessory attachments is not recommended by Chicco and could cause injuries or damage.
• Do NOT use with any bottle or item that is not intended to be heated.
• Do not place on or near a hot gas or electric burner, or in a heated oven.
• NEVER use the Sterilizer without the Lower Rack – Objects placed directly on the heating plate will cause damage to the object and the plate.
• NEVER place items on top of the Sterilizer.
• Do NOT use chemical sterilizing solutions/tablets or bleach in the Sterilizer.
• Always clean and rinse the objects before placing them in the Sterilizer.
• Not for space heating purposes.

CAUTION

• Do NOT let cord hang over edge of table or counter or touch hot surfaces.

• A short power cord has been provided to reduce the risk of it becoming entangled or being tripped over.

• Extension cords may be used if care is exercised in their use.

• If an extension cord is used, its electrical rating must be as great as the rating of the appliance and not draped over the edge of the countertop or tabletop where it could be pulled by children or tripped over. The extension cord should be a grounded type 3 wire cord.

• ALWAYS attach plug to appliance first before plugging the cord into the wall outlet.

• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, a polarized electrical outlet will only allow the plug to be inserted
  one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

• Remove plug from outlet when the appliance is not in use, before putting on or taking off parts, and before cleaning.
  Allow to cool before handling.

• Inspect carefully before each use. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner. If Sterilizer is faulty and/or not working correctly, switch it off immediately and unplug it from the wall outlet.

• To protect against electrical shock do not immerse cord, plugs, or Sterilizer in water or other liquid.

• Do NOT use if the Sterilizer, plug, or cord accidentally falls into water or becomes submerged.

• Only replace the filter with original Chicco replacement filters. The use of non-original filters may compromise the safety of the device and may cause it to malfunction.

Parts List

A. INTERFACE ON/OFF Icon
B. STERILIZE Icon
C. STERILIZE AND DRY Icon
D. FILTER Icon
E. DRY Icon
F. DELAYED START Icon
G. DESCALING Icon

Configurations
This Steam Sterilizer can be used in two different configurations.

|
---|---
FULL SIZE
Can be used to sterilize up to (6) Bottles and Nipples.| COMPACT SIZE
Can be used to sterilize accessories and other small items like pacifiers.

**Before First Use

**

Before using this product, the sterilization cycle should be performed (Pages 9-14) in the FULL SIZE configuration without any bottles in the Sterilizer.

Step 1
Make sure Sterilizer is unplugged and placed on a flat, stable, heat resistant surface. Remove the Sterilizer Lid, Upper Rack and Lower Rack.

Step 2
FOR FULL SIZE: Measure out 4.5 oz (130 ml) of water into a separate container. Pour directly into the Sterilizer Tank.
Continue on to page 11.
FOR COMPACT SIZE: Measure out 3 oz (90 ml) of water into a separate container. Pour directly into the Sterilizer Tank.
Continue on to page 12.
(Note: Using distilled water considerably reduces the formation of limescale on the heating plate.)

Step 3A
Always clean and rinse bottles and accessories before placing them in the Sterilizer.
FOR FULL SIZE: Replace the Lower Rack and arrange feeding bottles neck down. Place the Upper Rack and arrange bottle accessories. Place the Sterilizer Lid back onto the Sterilizer making sure that bottles and accessories do not prevent the lid from fitting correctly.

Step 3B
Always clean and rinse bottles and accessories before placing them in the Sterilizer.
FOR COMPACT SIZE: Place the Upper Rack and arrange accessories or pacifiers. Place the Sterilizer Lid back onto the Sterilizer making sure that objects do not prevent the lid from fitting correctly.

Step 4
Attach the power cord into the back of the Sterilizer. Always attach plug to appliance first. Plug the Sterilizer into an electrical outlet.
Power on the appliance by pressing the ON/OFF button on the back of the Sterilizer Base.

Step 5
Then turn on the Sterilizer by holding down the “INTERFACE ON/OFF” touch button on the front of the Sterilizer Base for 2 seconds. You will hear a beep and the touch button icons will all begin to flash indicating the Sterilizer is ready to start a cycle.
The Sterilizer can be run in 3 different modes.
FOR STERILIZE ONLY CYCLE: Pg. 15 -16
FOR STERILIZE AND DRY CYCLE: Pg. 17 -18
FOR DRY ONLY CYCLE: Pg. 19 – 20
(Note: If no cycle is selected for 3 minutes, the Sterilizer will beep and switch off automatically. Turn the Sterilizer back on by holding the “INTERFACE ON/OFF” touch button again for 2 seconds.)

Sterilize ONLY Cycle

Press the “STERILIZE” touch button.
When pressed, a solid white light will appear.

Then press the “INTERFACE ON/OFF” touch button to begin the cycle. The INTERFACE ON/OFF button will shine a solid white light to indicate that the cycle has started.
Continue to Step 6.
(Note: To turn off the Sterilizer mid-cycle, press the “INTERFACE ON/OFF” button. This will take you back to the select mode interface and you can select a different mode or turn off the Sterilizer by holding down the “INTERFACE ON/OFF” button. A long audible beep will be heard and lights on touch panel will turn off when Sterilizer is powered off.)

Sterilize and Dry Cycle

Press the “STERILIZE AND DRY” touch button. When pressed, a solid white light will appear. Press the “STERILIZE AND DRY” button repeatedly to cycle through the drying time options available: 20 minutes (recommended option for COMPACT mode), 30 minutes and 45 minutes (recommended options for FULL mode).

Then press the “INTERFACE ON/OFF” touch button to begin the STERILIZE AND DRY cycle. The INTERFACE ON/OFF button will shine a solid white light to indicate the cycle has started.
Once the sterilization cycle is complete, the timer will show a countdown of the remaining drying time.
Continue to Step 6.
(Note: To turn off the Sterilizer mid-cycle, press the “INTERFACE ON/OFF” button. This will take you back to the select mode interface and you can select a different mode or turn off the Sterilizer by holding down the “INTERFACE ON/OFF” button. A long audible beep will be heard and lights on touch panel will turn off when Sterilizer is powered off.)

Dry ONLY Cycle

Press the “DRY” touch button. When pressed, a solid white light will shine.
Press the “DRY” button again repeatedly to select the drying time.
30 Minutes and 45 Minutes: for FULL SIZE
20 Minutes: for COMPACT SIZE

After pressing the “INTERFACE ON/OFF” touch button to begin the DRY ONLY cycle. The INTERFACE ON/OFF button will shine a solid white light to indicate the cycle has started. The timer will show a countdown of the drying time remaining.
Continue to Step 6.
(Note: To turn off the Sterilizer mid-cycle, press the “INTERFACE ON/OFF” button. This will take you back to the select mode interface and you can select a different mode or turn off the Sterilizer by holding down the “INTERFACE ON/OFF” button. A long audible beep will be heard and lights on touch panel will turn off when Sterilizer is powered off.)

Step 6
Sterilization times may vary. When the cycle is complete, a long audible beep will be heard, the touch panel lights will turn off and the Sterilizer will turn off automatically.
Always clean your hands thoroughly before touching the sanitized objects.
Sterilized items will remain sterile inside the Sterilizer with the lid on for about 24 hours.
If there is a power outage during use of the Sterilizer, the cycle must be restarted. Allow the Sterilizer to cool completely before starting a new cycle or if complete, pour out water and dry thoroughly before storing in a cool, dry place.
When emptying water out of the Sterilizer Tank make sure to pour water away from the drying vent.

Delayed Start

The modes can be delayed for up to 2 hours before beginning the cycle. After selecting your mode and before you run the cycle by pressing the “INTERFACE ON/OFF” button, press the “DELAYED START” button. Press the “DELAYED START” button repeatedly until you have selected the desired time.
The delayed start can be set for 30 Minutes, 1 Hour, 1:30 Minutes and 2 Hours.
Next, press the “INTERFACE ON/OFF” button to start the cycle with a delay.
The timer will count down until ‘00’ and then the cycle will begin.
The delay can be skipped at any point by pressing the “INTERFACE ON/OFF” button again to skip the delay and run the cycle immediately.

Care and Maintenance

Make sure the Sterilizer is unplugged and the power cord is disconnected before cleaning. Clean Sterilizer regularly. After each use allow to cool down completely, pour out leftover water and dry the inside thoroughly. Use a soft damp cloth to clean the Sterilizer. Do NOT use bleach or any other harsh chemicals. Sterilizer is NOT dishwasher safe. Dry thoroughly before storing. Store in a cool, dry place. When cleaning the Sterilizer Tank, never immerse it in water or any other liquid.

Descaling
It is normal for deposits of limescale to form on the heating plate/tank or in the microwave base. These can vary in size and intensity according to the hardness of the water used in the appliance. An excessive deposit of limescale could reduce the performance of the appliance and damage it over the long term.
The product will signal the presence of scales and the need for descaling. Use a household descaling solution for the following steps.

1. Check whether the button/icon used to select the descaling option (G) is on or off. If the white indicator light for the button/icon is on the product needs descaling.

2. Switch off the device and allow it to cool completely.

3. Pour 4.5 oz (130 ml) of descaling solution into the hotplate/tank, following the instructions provided for the descaling solution.

4. Allow the solution to act for a maximum of 2 hours. Never switch the sterilizer on when the container is being soaked in the descaling solution.

5. Empty out the heating plate/tank.

6. Remove any residue with a soft cloth and rinse several times, pouring 7 oz (200 ml) of drinkable tap water into the heating plate/tank and then emptying it out.
   DO NOT place the appliance under running water. Finally, dry the appliance carefully with a soft dry cloth before using it again.

7. Before setting a new sterilization cycle, press and hold the descaling button/icon (G) for about 2 seconds until it switches off.
   CAUTION: Descaling operations should be performed every time the descaling button/icon (G) switches on. In the event of particularly hard water, descaling should be even more frequent and should be performed whenever limescale deposits are noted on the heating plate/tank. Do not use tools, abrasive sponges, detergents, alcohol, or solvents for cleaning as these may permanently damage the sterilizer.

Filter Replacement

The “FILTER” icon will light up to indicate that replacement of filter is needed. Filter is NOT washable and needs to be replaced at least every 4 months of use.
To replace the filter, make sure the Sterilizer is unplugged and has cooled down completely. Then unscrew and remove the filter compartment cover located underneath the Sterilizer Base. Remove the old filter and discard. Wipe out compartment with a dry cloth if needed. Insert the new filter with the fabric tab up towards the compartment cover. Screw the filter compartment cover back into place.

Before starting a new sterilization cycle, press and hold the “FILTER” icon/button for about 2 seconds until it switches off.

Trouble Shooting and Repair

The ON/OFF switch (located on the back of the appliance) is in the “OFF” position.| Check that there is power in the electrical outlet.
Move the switch to ON position.
The cord plug or the cord connector has not been plugged in correctly, or they are damaged.| Check that the plug and connector have been plugged in correctly, and that they are in good condition. Should the product still not work, contact Customer Service.
Appliance was submerged in water.| Discard unit.
The feeding bottles are stained at the end of the sanitation cycle.| There are scale deposits in the appliance.| The Sterilizer needs to be descaled. See the “Descaling” section for more details.
| High mineral content in tap water.| Use distilled water.
Noise — Incomplete cyde.| Excessive scale deposits on heating plate.| The Sterilizer needs to be descaled. See the “Descaling” section for more details.
The interface switches off and three audible beeps are heard in rapid succession.| Not enough water on the heating plate/container.| Place the correct quantity of water inside the heating plate/container and restart the cycle.
The thermal fuse is broken.| Contact Customer Service.
Rapid scale build-up.| Use of tap water with high mineral content, softened or treated water.| Use distilled water.
The Sterilizer needs to be descaled. See the “Descaling” section for more details.

For More Information

For USA customers :
Please do not return this product to the store.
If you have any questions or comments about this product, or are missing any of the parts, contact us in one of the following ways:

(877)-424-4226
info@chiccousa.com
www.chiccousa.com
1826 William Penn Way
Lancaster, PA 17601

Technical Information

Reference: 00007392100070
Electrical: 650W 120V~ 60Hz
Model: 06951_DU
Made In China

= WARNING!
**** = WARNING! Hot Steam.
= WARNING! Hot Surface.
www.chiccousa.com

References

• Chicco Baby Products | Car Seats, Strollers, Highchairs & More
• Chicco Baby Products | Car Seats, Strollers, Highchairs & More

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>