TELEFUNKEN TF-LED24S85T2 LED TV Instruction Manual

TELEFUNKEN TF-LED24S85T2 LED TV

Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating, and/or adjusting the product and keep the manual for reference in the future.

Before you start

Utilization of the product
If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Please unplug the power cord from the AC outlet and contact a service center for repair if the following occurs: any obvious abnormality appears in the unit, such as a smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.
• This unit can be connected to a power supply outlet without the third ground contact as well as with a ground contact.
• Always disconnect the power cord and antenna during a storm.
• Do not fix the power cord with a metal nail.
• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.
• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, twist, pull or roast the power cord.
• When connecting cables, make sure the power is switched off.
• Please contact the service center immediately if you found that the core is shown in the air or has been broken.
• Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.
• Never touch the antenna lie or power plug if it stars to thunder.
• Do not touch the power plug with wet hands.
• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.
• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.
• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.
• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.
• Over-press the panel may destroy the product.
• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as damage to the product.
• Please place the product on a flat surface in a well-ventilated location. Keep it away from burning light, direct sunlight, vibration, high temperature and humidity.
• Do not place any vase, potted plant, cup, medicine and any container with water on this product. If the liquid is spilt, it may cause a fire, electric shock or breakdown.
• Do not install it at the place on a strong magnetic field or current field. It may cause a breakdown. This equipment may be observe the deterioration of the picture by electromagnetic radiation in the electromagnetic environment.
• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.
• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.
• Do not place the unit into a closed space of TV for better ventilation; it can reduce the product’s lifetime. Keep a space at least 10 cm at above, left, and right of the TV.
• Please place all the signal cords behind of rear panel.
• Do not overexert or touch the panel when you convey the product. Do not transfer the LED TV up or down the display direction.
• Do not transport it with the power cord or the connection cable connected. If you move this product with the power cord or the connection cable connected, a damaged power cord, connection cable or connection terminal may cause fire, electric shock or breakdown.
• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it may damage it.
• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch

All images provided herein are schematic drawings and may differ from real objects.

Installation

Base installation

Cover a flat stable surface with a soft cloth. Place the TV unit facedown on the cloth. First align the holes on the back panel and the stands, then insert them into the slots.

Wall mounting

• Separate the stand from the cabinet before wall mounting.
• For wall mounting the back cabinet of this unit is equipped with 2 screw holes. Spread distance between the holes is 100*100 mm. A VESA wall-mount bracket should be used for wall mounting (the bracket is not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit. Wall or ceiling mounting implements must be durable and sufficient enough to support the weight of the unit.

Connection

Outdoor Antenna Connection
Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

• Connect the audio sources (Including DVD, VCDR, CAMCORDER and PC) to the proper Audio input jacks ‘L’ and ‘R’.
• Connect the video source to the Video input using an RCA cable.
• Plug the power cable in the electric outlet, making sure the current voltage is supported.
• When using the LED as a computer screen, connect the PC to the VGA jack from the monitor by the relevant cable (not included).
• This unit has PC audio in jack. Connect this jack to PC main unit with related audio cable in PC mode and adjust the volume to what you want.
• If the video source has a HDMI output jack, you can connect the signal to the monitor by the HDMI cable (not included).
• Coaxial output is intended for transmitting multi-channel sound to an external decoder (e.g. in 5.1-CH format). Coaxial cable should be used for connection.
• Connect your headphones or earphones (not included) to the headphone socket of this unit. When earphones are connected, the sound output through the built-in speakers of this unit is mute.
• PCMCIA slot is used for CI modules that are obtained from your digital TV provider.

Operation

Control elements

front panel

Back panel

1. Power cable
2. Earphone socket
3. PC input (VGA)
4. Composite AV input
5. PC audio input
6. Antenna input
7. Coaxial output
8. HDMI input
9. USB port
10. PCMCIA slot

Multifunction button

• Display Hide: press the multifunction button, the icon panel will pop up. It will turn off automatically after 5 seconds of inactivity.
• lcon selection: short press the button to select the wanted icon.
• lcon function selection: press and hold the button to achieve the function of the selected icon. They correspond to the RC buttons as follows:

1. (POWER/STANDBY) button
2. MENU button
3. SOURCE button
4. CH+ button
5. CH-button
6. VOL+ button
7. VOL-button

Remote controller (RC)

1. POWER button
2. Number buttons
3. DTVIATV button
4. P.MODE button
5. S.MODE button
6. MTS button
7. VOL+/NOL- buttons
8. FAV/LIST button
9. REC button
10. MENU button
11. Cursor (UP/DOWN/LEFT/RIGHT) buttons/ ENTER button
12. EXIT button
13. RED button
14. GREEN button
15. GUIDE button
16. TIMESHIFTII button
17.  CANCEL button
18. SUB.PG>I button
19.  TV/RADIO button
20.  SUBTITLE button
21.  SIZE button
22.  HOLD button
23.  MUTE button
24.  G button
25. SLEEP button
26. CH+/CH- buttons
27. REALIST button
28. FREEZE button
29. SOURCE button
30. DISPLAY button
31. CYAN button
32. YELLOW button
33. ASPECT button
34. INDEX button
35. REVEAL button
36. TEXT button

Changing the battery

1. Remove the battery compartment cover on the back of the ROC.
2. Insert two AAA batteries into the battery compartment making sure that the correct polarity is observed.
3. Install the cover back.
   • The RC should be pointed at the remote sensor within 8 meters and within 30 degrees at the left or the right side.
   • Take the battery out of the RC if it is not used for a long time.
   • Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.
   • Do not expose the RC to shock, or liquids, and do not place it in an area with high humidity.

General operations

• Press the button on the unit or on the RC to switch on the power. Press POWER button again to switch the unit off and go the the stand-by mode. To completely power off the unit unplug the power cable from the outlet.
• Press the VOL- button repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.
• Press the SLEEP button repeatedly to set the sleep time.
• Press GUIDE to launch the Electronic Program Guide (EPG) or for a fast reverse in recording (PVR) or Media Player mode.
• Press SUBTITLE to show and set the language of a current DTV channel.
• Press REC to begin recording of current playback in PVR mode.
• Press button on the RC to select from the present channel and the previously displayed channel.
• Press ASPECT button repeatedly to select a screen display size.
• Press MUTE button to cut off sound, press this button again or adjust volume to resume sound.
• Press TV/RADIO button to switch between TV and radio modes when watching channels.
• Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number directly.
• Press P.MODE button repeatedly to cycle through the available video picture modes.
• Press S.MODE button repeatedly to cycle through the available sound modes.
• Press DISPLAY button to display the preset TV channel play information.
• Press FREEZE button to freeze the picture on or off.
• Press FAV/LIST button to show the favourite channel list.
• Press MTS button in TV mode repeatedly to switch between various Nicam sound modes (can be unavailable for some channels).

Signal sources
Press SOURCE button, then press DOWN/UP cursor buttons on the RC or CH+/CH- buttons on the panel to select a source from available source list: DTV – ATV – AV – HDMI – VGA. Press ENTER button on the RC to confirm.

TELETEXT operations (option)

• Select the TV source mode. Then press CH-/CH+ buttons to select TV channel in order to pick up the picture signal of Teletext.

• Press CH-/CH+ buttons to select the previous page or the next page.

• Teletext button functions are as follows: ON/OFF: Press TTX button to enter into TEXT mode. Press this button again to return to the channel you are watching.

• HOLD: Press this button to stop the move to the next page. Press this button again to cancel operation.

• INDEX: Press this button to go to the index page.

• SIZE: Press this button to enlarge the text shown on the Teletext screen, and one-half of page could be shown. Press this button again to view the second half of this page. Press this button a third time to the normal size text page view.

• REVEAL: Press this button to reveal the canceled information. Press this button again to cancel the information.

• SUB.PG: Press this button to select sub page, and the sub-page symbol will appear in the left top-hand corner of the screen. Enter the number of sub pages and use numeric buttons in the format 0001 for sub-page 1. The Teletext will search for the sub-page.

• CANCEL: When a text page is selected,
  it may take some time before it becomes available; press this button to return to TV mode. When the required page is found, its number will be displayed at the top of the screen; press this button to return to the Teletext mode and browse the page.

• RED/GREEN/YELLOW/CYAN buttons: Press these 4 color buttons to access directly to the corresponding color page displayed at the lower parts of Teletext screen.

OSD operation

1. Press MENU button to enter the setting menu displayed on the screen.
2. Press UP/DOWN cursor buttons on the RC or CH+/- buttons on the panel to select setting page.
3. Press the ENTER button on the RC or VOL+ button on the panel to go to the parameter list.
4. Press UP/DOWN cursor buttons on the RC or CH+/- buttons on the panel to select a parameter to adjust.
5. Press cursor buttons on the RC or VOL+/-or CH+/- buttons on the panel to adjust the selected parameter.
6. Press EXIT button to quit the menu.  Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from actual menu tabs.

Channel setting

• Auto Tuning: press ENTER to select the country and tuner type for channels to start automatic search and saving of available ATV channels. After the search is finished, the unit will skip to searching DTV channels, Radio channels and Data. During the ATV search, press MENU button to skip to DTV, Radio and Data search.

• ATV Manual Tuning: Current CH: select channel number. Color System: select corresponding color system. Sound System: select corresponding sound system.  Fine-Tune: perform fine adjustment of the current frequency.
  Search: press LEFT/RIGHT buttons; the unit will search for next available channel downward or upward and save it under the current number.

• DTV Manual Tuning: Press LEFT/RIGHT cursor buttons to select channel number. Press ENTER button to start searching. If the selected channel number is available, the channel will be saved under the selected number. Press MENU button to quit.

• Programme Edit: this item allows you to sort TV programs according to your preferences. Enter the program edit menu:
  Delete: Select the channel you want to delete. Press red button to delete the channel. Move (not available for DTV channels with LCN): Highlight the needed channel. Press yellow button; select the position to put the channel into. Press yellow button to confirm.
  Skip: Highlight the needed channel. Press blue button; now this channel will be skipped when you select previous/next channels.
  Fav: select a channel and press the FAV button to add it to your list of favorite channels. Press FAV again to remove the channel from favorites.

• Signal Information: View the information on the current signal.

• CI Information (only in DTV mode): This function enables you to watch some encrypted services (pay services). Please insert a CI card into the PCMCIA slot according to the arrow on the CI card.

• The function can only be gotten when CI slot is available.

• It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.

• Please do not insert or pull out the CI card when power on. During initialization of the CI card, please don’t operate the TV.

• Do not insert or pull out the CI card frequently so as to avoid any damages of the TV and the CI card.

Picture setting

• Picture Mode: Dynamic/Standard/Mild/ Personal. When Personal mode is selected, you can adjust contrast, brightness, colour, tint (NTSC signal only) and sharpness of the image.
• Colour Temperature: Cold/Normal/ Warm.
• Noise Reduction: Dynamic noise reduction effect for reducing the video noise level. Select the Off/Low/Middle/High/Default mode. Sound setting SOUND Sound Mode Treble Bass Balance 0 Auto Volume Level Off AD Switch Off SPDIF Mode PCM
• HDMI Mode: adjust the picture settings when HDMI is selected as a source signal.

Sound setting

• Sound mode: Standard/Music/Movie/ Sports/Personal. When Personal mode is selected, you can adjust treble and bass.
• Balance: adjust the balance between the left and the right speaker.
• SPDIF Mode: Select the digital audio output mode: Auto/PCM/Off.
• Auto Volume Level : reduce the difference between channel and program volume automatically.
• AD Switch (in DTV mode): This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the Audio Stream for the AD (Audio Description), whenit is sent along with the Main audio from the broadcaster. Users can turn the Audio Description On or Off and control the volume.

Time setting

• Clock: You can display either the DTV signal stream time or set the system time.
• Time Zone: select your time zone.
• Sleep Timer: select the period until automatic switch-off of the unit.
• Auto Standby: select the period after which the TV turns off automatically if no input is given.
• OSD Timer: select the time during which the OSD menu stays visible.

Lock setting

• System Lock: The feature can prevent unauthorized operation of the TV set unless entering a 4-digit password. When Lock System is on and the system is locked, you must input the system password at Auto Tuning, Manual Tuning, Programme Edit or Default. Press the right number buttons for the password. The default password is 0000/8888. After a password correction has been confirmed, please remember it for entering into the Parent Guide menu, all functions can not be activated until the correct password is entered.
• Set password: You can set your private password. Press the number buttons on the remote control to set the new password. When the new password has been put in twice, the setting is finished successfully. The TV will go back to previous menu.
• Channel Lock (in TV/DTV mode): Press Green button to lock the available channel you want. Press the Green button again to unlock it.
• Parental Guidance: set the access to age-restricted content.
• Key Lock: lock and unlock the buttons on the TV set.
• Hotel Mode: when the Hotel Mode is enabled, the main menu is blocked. You can still control the volume as well as picture and sound modes, but channel search is restricted.

Setup menu

• Language: select the language of the on-screen display (OSD) menu. Setup menu
• TT Language: select the language of the Teletext.
• Audio Languages: select the language of audio (available for some DTV channels).
• Subtitle Language: select subtitle language (available for some DTV channels).
• Hearing Impared: When Hearing Impaired is on, the screen will give some information to people whose hearing is impaired. When Off, the information will be hidden.
• PVR File System (in DTV mode):
  • Select Disc: select the storage used for PVR. Time Shift Size: select the time for Time Shift.
  • Format: format the USB. Speed Check: display the speed of the storage.
• Aspect Ratio: select the screen aspect ratio or set it to auto.
• Blue Screen: enable or disable a blue screen showing when the TV signal is weak.
• First Time Installation: run the initial setting procedure.
• Reset: reset the parameters to initial factory settings.
• HDMI CEC: switch the HDMI Consumer Electronic Control feature on or off.

Screen setting (only in VGA mode)

• Screen Setting (only in PC mode): Auto adjust: automatic setting of the parameters.
  • Horizontal Offset: adjust horizontal position of the image.
  • Vertical Offset: adjust vertical position ofv the image.
  • Size: adjust the image frequency manually.
  • Phase: adjust the phase manually. Position Reset: reset the screen adjustment

USB operation

General playback information

• Insert a USB drive into the USB port. Select Media source and press ENTER button. The screen will show a USB playback window, in which you can select Music, Photo and Movie contents to play by pressing LEFT/ RIGHT cursor buttons and ENTER button.
• USB file systems supported: FAT16, FAT32, NTFS. 2.0 USB version is supported; maximum capacity 2 TB (NTFS). For correct and satisfactory operation, licensed USB devices of well-known brands should be used. Avoid using devices of unknown brands. Playback of some file formats cannot be supported.
• This unit supports playback of video files with ASF, AVI, MKV, and MPG extensions, with video codecs WMV9, DIVX, H263, MPEG-4, MPEG, XVID, and audio codecs WMA, MP3, DD(AC3).

The above list of extensions and codecs is for information only and is not a guarantee that all files having the above extensions and codecs should be read by this unit.

• Some AVI files cannot be played due to their parameters and recording conditions. Video files with an AVI extension exceeding 2 GB in size may be played partially. According to the USB 1.1/2.0 Standard, usage of a USB device with power current consumption exceeding 500 mA is not recommended without a supplementary power supply. Failure to use supplementary power for connected USB drives with power consumption exceeding this value as well as defective USB drives may cause mechanical or thermal changes of elements of this unit as well as the failure of internal elements of the USB port. Such damages are not warranty cases. Warning: usage of external USB drives containing BIN files in the root directory may cause malfunction of the unit or damage to the software.

Operations of file playback

• Insert a USB into the USB port. Press the SOURCE button or select USB source and press ENTER button on the RC or VOL+/VOLbutton on the unit. The screen will show a USB  playback window, in which you can select music, Photo, and Movie contents to play by pressing the LEFT/RIGHT cursor buttons and ENTER button.
• In the context menu, press the cursor buttons to select a folder, press ENTER button to enter it, then press the cursor buttons to select the file you want to watch or to listen to. Press ENTER to play the selected file.
• While playback, press ENTER button; the bottom of the screen will show a playback menu in which you can select an operation by LEFT/ RIGHT cursor buttons or perform this operation by pressing the ENTER button.
• While playback, press the button to pause or resume playback. Press the button to stop playback.
• When playing music files you can press / buttons to fast reverse or forward. You can press / the buttons to select the desired files manually in normal conditions.
• When playing photo files, you can press the buttons to page up or page down the file. Press the LEFT/RIGHT cursor buttons to rotate the image.
• Press the EXIT button to stop playback and return to the previous menu screen.

Electronic programme guide (EPG)

If you know the airing time of the current programme you can access the EPG menu by pressing the GUIDE button on the RC. The menu displays the list of the current available channels on the left, and the name of each programme starting in scheduled time periods on the right. Select the channel by pressing UP/DOWN and the programme by pressing LEFT/RIGHT. Follow the on- screen instructions and use color buttons to navigate this menu.

PVR/Timeshift function

Insert a USB drive, the system will automatically create a folder to store the files recorded. Recording begins when REC button is pressed, and it records all the time until button is pressed or the memory is full. PVR/Timeshift is a feature enabling you to record an air program while you are away. Press button to activate Time Shift while recording. Press UP/DOWN cursor buttons tozoom in/out the Timeshift menu. You can operate by referring to PVR/Timeshift menu on the screen.

CI information
(only in DTV mode): This function enables you to watch some encrypted services (pay services). Please insert a CI card into the PCMCIA slot according to the arrow on the CI card.

• The function can only be available when CI card is present.
• It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.
• Please do not insert or pull out the CI card when power on. During initialization of the CI card, please don’t operate the TV.
• Do not insert or pull out the CI card frequently so as to avoid any damages of the TV and the CI card.
• If there is no picture and/or sound with the CI+ CAM module inserted, please contact the customer support of the service provider.

Troubleshooting

Below is a table describing simple measures that can help you eliminate most problems likely to emerge when this unit is in use. If below measures do not help, turn to a service center or to the nearest dealer.

in. Contrast, brightness, color and volume are all in the minimum value or TV is in mute mode.| Plug the power cord in. Alter the value of contrast,

brightness, color and volume.

Picture and sound with abnormity| Contrast and color are set improperly. Color system is set improperly.

Sound system is set improperly.

| Set the value of Contrast and color properly.

Set the sound system properly.

The picture in VGA mode is abnormal| The PC settings may be improper.| Check and set the resolution parameters of your PC.
Picture is spotted or with snow| Signal source is low-grade or the signal is in a lower quality.| Use the qualified signal cord.
Blue background| No video signal or the signal cord is improperly/not connected.| Connect the signal cord properly.
No sound| No audio signal or the signal cord is improperly/not connected.| Connect the audio signal cord properly.

Set the sound system properly.

The RC does not work| Batteries are improperly installed or exhausted.| Make sure the positive and the negative polarities are correct. Reattach the battery lid.

Replace the batteries.

Causes of interference
Incorporated in your TV receiver are the most up-to-date devices to eliminate interference. Local radiation however, can create disturbances, which visibly affect your picture. Proper installations, a good aerial are your best safeguards against these disturbances.

• RF INTERFERENCE: Moving ripples across the screen are caused by nearby transmitting or receiving short-wave radio equipment.
• DIATHERMY: Herringbone pattern and partial picture loss can result from the operation of diathermy equipment from a nearby doctor’s surgery or hospital.
• SNOW: Weak TV signals from long distant stations result in an instead picture and give the effect of falling snow. An antenna adjustment or antenna amplifier may be needed.
• GHOST: Multiple image, caused by TV signals reflected back from surrounding buildings, hills, aircraft, etc. is minimized by correct aerial positioning.
• CAR IGNITION: Nearby cars and electric motors can cause small streaks across the picture or make the picture roll.

General Information

Accessories

1. LED TV  1 pc
2. Remote controller 1 pc
3. Stand 2 pcs
4. Instruction manual 1 pc

Specifications

• Size (diagonal) 23.6″ (60 cm)

• Resolution 1366x768B

• Aspect ratio 16:9

• View angle: vertical, horizontal 178°, 178

• Response time 8.5 ms

• Color system  PAL, SECAM

• Sound system  B/G, DK,

• NICAM stereo 2 x3W

• Composite AV RCA input +

• PC audio input+

• VGA input+

• HDMI input+

• Headphone jack +

• Coaxial digital output +

• DVB-T/DVB-T2/DVB-C signal reception +

• PCMCIA interface (CI, C+) +

• Russian and English OSD +

• Progressive scan +

• Digital comb filter 3D

• Sleep timer +

• USB movie, audio, and photo support +

• Quantity of channels 100 analog/1000 digital

• Teletext 899 pages

• Electric shock protection class

• Nominal voltage range: AC 100-240 V; 50 Hz

• Unit dimensions: without stand 551 x 328.4 x 70.3 mm

• with stand 551 x 364.8 x 180.7 mm

• Net weight 2.4 kg

• Net weight
  

• Operating conditions
  

• Ambient temperature from 5 to 35 °C

• Relative humidity from 45% to 75%

• Atmospheric pressure from 86 to 106 kPa (650-800 mm Hg)

The LED panel is a high-technology product with many thin film transistors that can give you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green, red, black or white, please note that this does not affect the performance of your LED TV. Warning: Specifications may be subject to change without notice for improvement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>