Shenzhen Link Win Technology R53-MS5314G Mobile Phone User Guide

User Guide

Model: MS5314G

Turn on the device:
press the power button for at least 4 seconds.

First time power on:
– It’s normal that the first time Power On, the device takes a while to finish booting. -Once Is started, be presented with a quick setup guide on the screen (this is a default of the Android operating system). Follow it step by step to easily configure your device and to start enjoying it.

Suspended device:
– by briefly pressing the power button will enter the sleep mode of the machine (the screen is off, and some services are stopped, in order to minimize the consumption of the machine).
– To Reuse your unit, briefly press again the power button. After a while, you can use the device again normally.

Power off the device:
– by pressing the power button for a few seconds, will be presented on the screen can completely turn off the unit.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The EUT was tested and rated under the American National Standard Institute (ANSI) C63. 19-2011 hearing aid compatibility standards. The ANSI standard for hearing aid compatibility contains two types of ratings:

• M-Ratings: Rating for less radio frequency interference to enable acoustic coupling with hearing aids.
• T-Ratings: Rating for inductive coupling with hearing aids in telecoil mode. This device complies with the FCC HAC requirements has also been tested E-Field, H-Field, and T-Coil.

M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference to hearing devices than phones that are not rated. M4 is the better/higher of the two ratings. Your device is rated M3.

T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to be more usable with

a hearing aid’s telecoil than phones that are not rated. T4 is the better/higher of the two ratings. Your device is rated T3.

SAR Information Statement

Your Mobile Data Terminal is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluations of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted a requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is 0.55W/Kg and when worn on the body, as described in this user guide, is 0.78 W/Kg (Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements). The maximum scaled SAR in hotspot mode is 0.79 W/Kg. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section ofhttp://www.fcc.gov/oet/ fccid after searching on FCC ID: 2AQ4G-MS5314G Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) web-site at[ http://www .wow-com.com](http://www.wow-com.com) . In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements.

The SAR test distance is 10mm.

Documents / Resources

| Shenzhen Link Win Technology R53-MS5314G Mobile Phone [pdf] User Guide
MS5314G, 2AQ4G-MS5314G, 2AQ4GMS5314G, R53-MS5314G Mobile Phone, Mobile Phone
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>