TESLA GM610BF Vision Gaming Monitor User Manual

TESLA GM610BF Vision Gaming Monitor

NOTE
This device is intended for household use exclusively. Professional and/or commercial use of a device intended for household purposes shortens its working life and has a negative effect on the device’s performance characteristics.

IMPORTANT SAFETY PRECAUTIONS

1.  Please read all the instructions carefully before using this product.
2. BE SURE TO unplug the power cord when cleaning the LCD. Never clean it with liquid detergent or spraying detergent, but wipe it with wet soft cloth. If it is still not clean, please use special detergent for LCD.
3.  DO NOT use accessories not authorized by the manufacturer, otherwise, they may incur danger.
4. . When disconnecting the power cord of the display or power adapter, always remember to hold the plug instead of pulling the wire to unplug the power cord.
5. Keep the display away from water sources such as bathtub, washbasin, sink or washing machine. DO NOT place the display on wet floor or near a swimming pool, or press LCD surface with fingers or hard objects.
6. The grooves and openings on the back and bottom of the shell are for ventilation purpose and also for guaranteeing the reliability of the elements and preventing them from overheating; in order to prevent the vents from blocking; DO NOT place the display on bed, sofa, carpet or other similar surfaces; DO NOT place the display near to or on heat radiator or heater; DO NOT put the display into the embedded device, unless it is provided with adequate ventilating equipment.
7.  Only the type of power source indicated on the nameplate applies to this display. If you have any questions on the type of power source you use, please consult the dealer of the display or local administration of the power supply.
8. For safety, the display or the power adapter is equipped with a three-pin plug power cord. The third pin of this plug is for grounding, and only applicable to sockets that is correctly grounded. In case your socket is not available for the plug, please contact an electrician to replace the socket.
9.  Since there is high voltage or other risks when the shell is opened or moved, please DO NOT repair the display by yourself, but request qualified maintenance staff to carry out.
10.   In one of the following cases, please unplug the display or the power adapter and ask qualified maintenance staff for help:
11. . The display falls off or the shell is damaged.
12. The display is obviously abnormal.
13.  Please place the display in a cool, dry and well-ventilated place.

Store the display in the temperature range of -10°C~60°C, beyond which the display may be damaged permanently.

PRODUCT DESCRIPTION

As a high-performance smart multi-frequency scanning display,it adopts active- matrix TFT-LED backlight liquid screen and is controlled with MCU digital technology. With compact and thin appearance and build-in power supply, it is suitable for narrow work space.

Packing list
Please check the following items in the packing case before installation:

• One LCD display (including the base)
• One HDMI cord, one power cord, one AC adaptor
• One user manual, One warranty card
  If any of above items is missing, please contact with the dealer.
  Attention: Accessories shall be subject to the real configuration. Please keep all packing materials well for product transport in the future.

INSTALLATION AND CONNECTION

Display installation

• This machine should be installed adjacent to an easily pluggable AC power socket.
• For the sake of safety, we suggest that suitable wall-mounted bracket or base be used.
• In order to prevent injury, this machine shall be placed on a stable and level surface or fixed on a firm wall.
•  For wall-mounting, please ask a professional to do so. Improper installation may cause instability of this machine.
• DO NOT place this machine in places with mechanical vibration.
•  DO NOT install this machine directly opposite to air-conditioner, otherwise its inner panel may bedewed and cause failure.
• DO NOT place this machine in places with strong electromagnetic field, otherwise it may be interfered by the electromagnetic wave and get damaged.

Signal line connection
Connect the signal line to output interfaces signal of HDMI/DP signals of PC, and then connect the other end of the signal line to the corresponding signal input port of the display.
Audio output
This machine supports earphones and external speaker audio output.

OPERATION OF DISPLAY

The OSD control buttons are shown as the figure. Models of the same product series are only different in button position and panel pattern, please refer to the practical model.

Power indicator light

When the display is working normally, the blue indicator light is on; when it is in the energy saving state, the indicator light blinks with red color; when the signals are sent again in the energy saving state, the machine will return to normal work; when the machine is in the standby state, the indicator light is off. As the display is still powered in the standby state, for the sake of safety, the power cord should be unplugged when the display is not used.

BASIC TROUBLESHOOTING

socket are well connected to power, and whether the display is in the shutdown mode.
Image blurring, over-large, over-small, etc.| Enter the menu “Image Setting” and select “Auto Image Adjust” to automatically adjust the display.
Image over dark| Enter the menu “Brightness and Contrast” to adjust the brightness and contrast of the display.
Display over heat| Leave at least 5cm of distance for ventilation around the display and do not place articles on the display.
Dark/ light spots when powering on| This is a normal phenomenon. It is due to the backlight illuminates unevenly at the initial phase of powering on caused by temperature difference. The backlight can illuminates normally after 20 minutes, and then the dark/light spots will be corrected.
Image distortion, blinking, shaking| Check computer setting, select the correct resolution and re-adjust the refresh frequency.
Power off noise| It is a normal phenomenon caused by display discharging in the process of powering off.

Safety protection
When the video signals of PC exceeds the frequency range of the display, the horizontal and field synchronizing signals will be shut down to protect the display. Then, you have to set the PC output frequency to an acceptable range so as to make the display work normally.

BASIC TROUBLESHOOTING

socket are well connected to power, and whether the display is in the shutdown mode.
Image blurring, over-large, over-small, etc.| Enter the menu “Image Setting” and select “Auto Image Adjust” to automatically adjust the display.
Image over dark| Enter the menu “Brightness and Contrast” to adjust the brightness and contrast of the display.
Display over heat| Leave at least 5cm of distance for ventilation around the display and do not place articles on the display.
Dark/ light spots when powering on| This is a normal phenomenon. It is due to the backlight illuminates unevenly at the initial phase of powering on caused by temperature difference. The backlight can illuminates normally after 20 minutes, and then the dark/light spots will be corrected.
Image distortion, blinking, shaking| Check computer setting, select the correct resolution and re-adjust the refresh frequency.
Power off noise| It is a normal phenomenon caused by display discharging in the process of powering off.

TECHNICAL SPECIFICATIONS OF PRODUCT

Requirements for working environment Barometric pressure

Working temperature and humidity Warehousing temperature and humidity

|

86kpa~104kpa  0ºC~40ºC                               20%~85%

-10ºC~60ºC      10%~90%

Packing size (L x W x T) and weight Unpacked size (L x W x T) (with base) Packing size (L x W x T)

Net weight Gross weight

|

616×524.5×290.3mm

800x535x185mm 5.35kg

7.95kg

Power supply management system

Remarks: All technical specifications in this manual and external packages are subject to change without further notice. In case that there is subtle difference between this manual and practical operation, please follow the practical operation.

INSTRUCTION OF BASE INSTALLATION

Installation steps of the base:

1. Remove the styrofoam on the back;
2. Align the hole of support with the VESA hole of the backcover, and lock with 4 M4x16 screws (4 in a bag);
3.  Insert the base into the support;
4. Lock with 3 M4x16 screws (3 in a bag).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>