AX2V DV-720WM Car Dash Cam Front 1080P FHD WiFi Dash Camera for Cars Instruction Manual

DV-720WM Dash Cam Installation Manual

 DV-720WM Car Dash Cam Front 1080P FHD WiFi Dash Camera for Cars

1. Locate The Car Fuse Box, The Position of The Fuse Box Varies By Car, Please Refer To Your Car’s Manual.
2. Open The Fuse Box, Usually, There Will Be a Current Introduction of The Fuse Slot Interface on The Back of The Car Fuse Box Cover. You Can Refer to It Before Wiring. For Example as Below.
   NO| Electrical system| Capacity
   ---|---|---
   1| Alarm/lmmobiliser| 10A
   2| Audio| 15A
   3| Hazard| 15A
   4| Meter/Diagnostic| 10A
   5| Horn| 15A
   6| Audio| 15A
   7| Power Socket| 20A
   8| Power Mirror| 10A
   9| Alarm/Turn RH| 7.5A
   10| Alarm/Turn LH| 7.5A
   11| Alarm/lmmobiliser| 10A
   12| Airbag| 10A
   13| ECU| 15A
   14| TCU| 15A
   15| Back up lamp| 5A
   16| Alarm/Diagnostic| 10A
   17| Turn signal| 10A
   18| Power window*| 25A
   19| HVAC/Defogger| 10A
   20| Wiper| 20A

Note: Strongly advised not to connect hardwire kits wire to any of fuse’s related to vehicle safety system.Recommended Acc signal: Fuse No. 6 Audio, Fuse No. 7 Power Socket or Fuse No. 8 Power Mirror. Recommended Battery signal: Fuse No. 2 Audio, Fuse No. 3 Hazard.

3. After located the fuse point, you need to double confirm whether the fuse is providing the signal as we needed. To confirm the signal, you will need below tools:

4. Confirm Battery Signal:（the fuse has electricity even if the car engine is off）
   Note: Ignition switch position must be in lock position.

5. Confirm ACC signal:（The fuse only has voltage when the car’s engine is on）
   Note: Ignition Switch position must be in ACC position. You should get voltage reading on multimeter or light up on circuit tester. Reconfirm the fuse slot again with Ignition Switch position in Lock position and recheck the fuse slot using multimeter or circuit tester. You should not get any voltage reading on your multimeter or circuit tester not light up during Ignition Switch in Lock position.

6. Confirm Ground Point:（metal parts of the vehicle）
   Refer to below picture; use multimeter to check continuity mode. Find any screw direct tighten to vehicle body and measured the screw point against the vehicle body. A good ground point must get continuity reading at < 0.1 ohm.*Now you have determined the ACC signal, Battery signal and ground connection point. It’s time to connect the hardwire kits to the dash cam.

7. Connect The Wires:Yellow Cable (BATT / B +)-Connected To The Car Battery Constant DC +12V Power.
   Red Cable (ACC)-Connected To The ACC DC+12V Power.
   Black cable (GND)-Connected To The Vehicle Metal Body.

Note: The definition of the fuse box will be different for each vehicle, the above information is for reference only. Please refer to the actual situation of the actual vehicle for details. Accurate information can also be found in the vehicle’s owner’s manual or with your local car dealer.
Thanks for reading, hope it helpful for you！

Documents / Resources

| AX2V DV-720WM Car Dash Cam Front 1080P FHD WiFi Dash Camera for Cars [pdf] Instruction Manual
DV-720WM Car Dash Cam Front 1080P FHD WiFi Dash Camera for Cars, DV-720WM, Car Dash Cam Front 1080P FHD WiFi Dash Camera for Cars, Front 1080P FHD WiFi Dash Camera for Cars, WiFi Dash Camera for Cars, Dash Camera for Cars, Camera for Cars, Cars
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>