BIXOLON SRP-Q200 Thermal Receipt Printer Installation Guide
- June 6, 2024
- BIXOLON
Table of Contents
BIXOLON SRP-Q200 Thermal Receipt Printer
KN04-00174A (Ver.1.1)
THERMAL RECEIPT PRINTER SRP-Q200
Information
This installation guide contains only simple information required for the installation of the product. Detailed information of the installation can be found on the “Download” tab of BIXOLON website (www.bixolon.com) and, it includes the following contents.
- Manual: User’s Manual, Code Page Manual, Command Manual, Network Manual, Software Manuals
- Driver: Windows Driver, OPOS Driver, JPOS Driver, CUPS (Linux, Mac) Driver, Virtual Port Driver
- SDK: Windows POS SDK, iOS SDK, Android SDK, Xamarin SDK
We at Bixolon Co., Ltd. constantly strive to improve product functions and quality. To do this, the specifications of our product and the contents of the manual may change without prior notice.
Components
Cable Connection
- Turn off the printer and POS System (host computer).
- Separate the Cover-Rear like to picture.
- Connect the power cord to adaptor and connect the adapter to the power connector of the printer.
- Check the type interface located at the back of the printer and connect proper cable.
- Please plug the cash drawer cable in the DK port at the rear side of the printer.
※ Do not use an adapter that was not supplied with the printer.
※ To detach Cover-Rear easily, press Cover-Rear Open Button.
Installing Paper Roll
- Open the paper roll cover by pull the Cover-Open Lever.
- Insert new roll paper in the correct direction.
- Pull the paper out slightly and close the cover.
Note
Hold down the center of the cover firmly when closing the cover so that the
paper maintains close contact with the roller. Printing quality may not be
optimum if recommended paper is not used.
Paper Jam (Refer to 1-8 in User’s Manual)
- Turn the printer off and on, open the cover, and remove the paper.
- If cover does not open, please contact Customer Service.
Using Control Panel
-
Power LED (Indicator Lamp)
The Power light is on whenever the printer is on. -
Error (Indicator Lamp)
Red light will be on in various error conditions such as out of paper, cover open, etc. -
Feed (Button)
Press this button to feed the paper out.
Hold down this button to feed out the paper continuously.
Self-Test
-
Check whether paper is mounted correctly.
-
Turn on the power while holding down the Feed button and the self-test procedure will begin.
-
Printer will print out the current status of printer including the version of ROM.
-
After printing out the current status of printer, the printer will print following lines and waits for the next step (paper lamp will keep blinking).
SELF-TEST PRINTING.
SELECT MODES BY PRESSING FEED BUTTON.
Continuous test printing : Less than 1 second
VMSM Selection : 1 second or more -
Press the Feed button to resume printing or hold down the button for at least one second to change the VMSM settings.
If “Continuous SELF-TEST” is selected
Press the Feed button for less than one second to print the preset page.
The self test ends automatically as it prints the following line and cuts the paper.
COMPLETED
The printer goes into normal print mode upon completion of the self test.
If “VMSM Selection” is selected.
The following lines will be printed when the VMSM opens
VMSM Selection
0 : Exit and reboot printer
1 : Print current settings
2 : Set Print Density
3 : Set Cutting mode
4 : Set External Buzzer after cutting
5 or more : None
Press the Feed button to run the above function.
Step 1(Select Options): press the button a number of times as shown by each menu.
Step 2(Enter Options): hold down the button for at least one second to apply each item selected.
Note
If you select any items not listed above, the list of “VMSM Selection” will be printed again. Setting the mode will be canceled if no item is selected in Step 1.
Hold down the Feed button for at least 1 second to save the changes.
The following line will be printed before cutting the paper.
** COMPLETED
Attention
**If “0: Exit and reboot printer” is not executed, the new settings will not be saved. -
The new settings will be automatically applied when printer resets.
Note
You can check whether printer works correctly or not through the self-test.
Printing quality, ROM version, and memory switch settings can be checked
through the self-test function.
Reconfiguration of Printer
SRP-Q200 does not support Dip Switch. To change the settings of the printer,
use the virtual memory switch utility or virtual memory switch control
function for self-diagnosis.
WEEE(Waste Electrical and Electric Equipment)
This marking shown on the product or its literature, indicates that is should
not be disposed of with other household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Safety Precautions
In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage.
WARNING
Violating following instructions can cause serious injury or death.
CAUTION
Violating following instructions can cause slight wound or damage the
appliance. 
BIXOLON Co., Ltd.
-
Website http://www.bixolon.com
-
Korea Headquarters
(Add) 7~8F, (Sampyeong-dong), 20, Pangyoyeok-ro241beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 13494, Korea (ROK)
(Tel.) +82-31-218-5500 -
U.S. Office
(Add) BIXOLON America Inc. 13705 Cimarron Ave Gardena, CA 90249
(Tel.) +1-858 764 4580 -
Europe Office
(Add) BIXOLON Europe GmbH, Tiefenbroicher Weg 35 40472 Düsseldorf
(Tel.) +49 (0)211 68 78 54 0