SALUS RT310i Smartphone Wireless Controlled Thermostat Installation Guide

: June 6, 2024
: SALUS

SALUS RT310i Smartphone Wireless Controlled Thermostat Installation Guide

Introduction

The SALUS RT310i is a Smart phone controlled programmable thermostat. The RT310i thermostat will switch your heating system on or off, as needed, in accordance with the temperature set by you, locally on the device or remotely using the dedicated app.

Product Compliance

This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com

Safety Information

Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel.

Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply.

The thermostat is pre-set from factory in Manual Mode allowing you to set the desired temperature. This is the default working mode if not connected to the internet during installation.

Button Functions

Turn on the LCD backlight
Turn On/Off the Frost Mode
Increase button
Decrease button
Test Mode/ Pairing Mode

Installation – Step 1

1. RXRT510

Wire up the receiver according to the diagram and switch it on before inserting the batteries into the thermostat.

Installation – Step 2

2. RT310iTX

Before inserting the batteries, please make a note of your SRT number and register your device on the app.

Installation – Step 3

Pairing Process

Press the button for 3 sec. Wait 9 min or if the red light goes steady, press the pairing button again for 3 sec.

Testing Process

Press the button once to test the connection. If the devices are paired the ON and AUTO LEDs will both flash. You can wait 9 min for the process to end or can press the button again to stop.

Registration

Download the RT310i App, create an account and register your device. Follow the on screen instructions to complete all the steps.

Device Settings Via the App

Features available only on the App:

Temperature format
Clock format
Time zone
Daylight Saving Time
Heating or Cooling Mode
Temperature accuracy
Display tolerance
Temperature offset
Schedule/Manual/Off Mode
Holiday Mode
Location Mode
Delay Start

Customize your setttings according to your preferences. Time and date will be set automatically once connected to the internet. Set the mode (heat/cool). Heat Mode is used for controlling a heating boiler. Cool Mode is used for controlling a cooling device. In Cool Mode, you can choose temperature accuracy between ± 0.5 °C and ± 0.25 °C. In Heat Mode, you can select as well between a lower comfort level (6 on/off cycles
per hour) and a higher comfort level (9 on/off cycles per hour). Also, in order to calibrate the temperature, you can offset it using a ± 3 °C range.

General Operation

There are 3 program settings. 1. Schedule (7 days, 5-2 days and 24 hours), 2. Manual and 3. Off.

In Manual Mode you will permanently override the schedule. Exit Manual Mode by switching to Schedule or turning off the thermostat.

If the internet connection is lost the thermostat will follow the schedule. If it was in Frost Mode you can disable the Frost function from the device and continue following the schedule (see Frost Mode section of the guide).

Frost Mode

Frost protection temperature can be set between 5.0oC and 9.0oC. To turn on Frost Mode activate Off
Mode or Holiday Mode via the App.

Frost Mode can also be de-activated or activated on the device, by pressing the frost button once.

Holiday Mode

Select the period for this function. Frost Mode temperature will be activated during this period.
After the Holiday Mode ends, the thermostat will follow the previous setting (Schedule, Manual or Off.)

Location Mode

Location Mode is an automated task designed to change your heating settings according to the current distance from your home.

If Location Mode is enabled, you can drag the slider in order to set the distance limit. Go to “Setting” to manage your settings
.

Select your devices and the actions you want to take place when you leave and return home. Choose “SAVE” to confirm. Your
devices will be automatically adjusted to the settings you make.