Haier HBS01 AC Remote Control Operating Manual

Haier HBS01 AC Remote Control Operating Manual

External View of Remote Controller

Loading of the battery

1. Remove the battery cover;
2. Insert AAA batteries (included) loading is in line with the “+”/ “-”;
3. Replace cover

Functional description

1. Power-up and Show All: After inserting the batteries the display will show all symbols for 3 seconds. The remote will then enter clock set mode. Use “+/-“ to adjust the clock. Press “Confirm” when done. If no action is taken within 10 seconds then the remote will exit set mode. See section 22 for clock setting instructions.
2. ON/OFF Button: Press the ON/OFF button on the remote control to start the unit.
3. SMART Button:
4.  In SMART mode the air conditioner will automatically switch between Cool, Heat, or Fan to maintain the set temperature.
5.  When the fan is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature.
6.  The SMART button also works to power the unit on and off.
7. COOL Button, HEAT Button, and DRY Button
8.  In COOL mode, the unit operates in cooling. When the FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. COOL will be displayed during COOL mode.
9.  In HEAT mode, warm air will blow out after a short period of time due to the cold-air prevention function. When the FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. HEAT will be displayed during HEAT mode.
10.  DRY mode is used to reduce humidity. In DRY mode, when room temperature becomes lower than temp. setting+2°F, the unit will run intermittently at LOW speed regardless of the FAN setting. DRY will be displayed during DRY mode.
    Mode| SMART| HEAT| COOL| DRY| FAN
    ---|---|---|---|---|---
    Initial TEMP.| 24°C (75°F)| 24°C (75°F)| 24°C (75°F)| 24°C (75°F)| Setting temperature is not showed.
    Mode| SMART| HEAT| COOL| DRY| FAN
    Initial Fan Speed| AUTO| LOW| HI| AUTO| LOW
11. FAN SPEED Button: Fan speed selection
    • Press the FAN SPEED button. For each press, the fan speed changes as follows

The air conditioner fan will run according to the displayed fan speed. When the FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature.

TEMP. +/- Buttons

• Temp+ Every time the button is pressed, the temperature setting increases.
• Temp- Every time the button is pressed, the temperature setting decreases.
• The operating temperature range is 60°F -86°F (16°C-30°C).

Quadrant Control
(Available for some models):

1. This setting allows the vertical airflow to be adjusted individually on each side of the unit. (1) Initial default positions.
   | SMART| HEAT| COOL| DRY| FAN
   ---|---|---|---|---|---
   Selected Quadrant| Show all| Show all| Show all| Show all| Show all
   Vertical SWING Angle| Position 3| Position 5| Position 3| Position 3| Position 3
2. Press the Quadrant Control button to select the quadrant. Each button press will select as shown bellow
3. Once desired quadrant is selected then use the Vertical Swing button to set the direction of airflow. See section 9.

Vertical SWING Button

Air Flow Direction Adjustment
Press the SWING UP/DOWN button to choose the position of the vertical airflow louvers.

Status display of airflow COOL/DRY

Horizontal SWING Button
Press the SWING LEFT/DOWN button to choose the position of the horizontal airflow louvers.

Status display of airflow COOL/DRY/HEAT

HEALTH AIRFLOW (Available for some models)
The Health Airflow function will stir the air in the room.

1. Press the “HEALTH AIRFLOW” button to show the icon on the LCD display.
2. The Quadrant icon will cycle to each quadrant.
3. The horizontal swing default oscillates. It can be adjusted with each press of the Horizontal SWING Button between narrow, mid, wide and left to right.
4.  The vertical swing is not adjustable.
5. Fan speed default is variable. It can be adjusted by pressing FAN SPEED Button between low, medium, and high.

REMOVE IMAGES

Sleep Operation Mode:

1. SLEEP mode during COOL, DRY modes
   One hour after SLEEP mode starts, the temperature will rise 2°F .above the set temperature, and after another hour, the temperature rises an additional 2°F. The unit will run for an additional six hours, then turn off. The final temperature is 4°F higher than the initial set temperature. Using this feature will help with achieving maximum efficiency and comfort from your unit while you sleep.

2. SLEEP mode during HEAT mode
   One hour after SLEEP mode starts, the temperature will decrease 4°F below the set temperature, after another hour, the temperature will decrease an additional 4°F. After an additional three hours, the temperature will rise by 2°F. The unit will run for an additional three hours, then turn off. The final temperature is 6°F lower than the initial set temperature. Using this feature will help with achieving maximum efficiency and comfort from your unit while you sleep.

3. In SMART mode
   The unit operates in the corresponding sleep mode adapted to the automatically selected operation mode.
   Note:
   When the TIMER ON function is set, the sleeping function cannot be set. If the sleeping function has been set, and the user sets the TIMER ON function, the sleeping function will be canceled, and the unit will be set to the timer function.

HEALTH

1. During power-on or power-OFF, press the “HEALTH” button to display an icon on the LCD display, and press the “HEALTH” button again to cancel.
2. During power-OFF, press the “HEALTH” button to enter Fan mode, start low wind and HEALTH function, and display the icon .
3. Switch among modes, and keep the HEALTH function.
4. If the HEALTH function is set, power OFF and then on to stay in HEALTH mode.
5. The EALTH function is not available for some units.

ECO

1. Press the ECO button and the display will show.
2.  ECO is valid under all modes, it is memorized among switches of all modes.
3. ECO function power-on or power-OFF is memorized.
4. The ECO function is not available for some units.

Turbo/Quiet
The TURBO function is used for fast heating or cooling. Press the TURBO button, the remote control will display the TURBO, and switch the fan to SUPER high. Press the TURBO button again to cancel the function.
Press the QUIET button, the remote control will display the QUIET and switch the fan to BREEZE. Press the QUIET button again to cancel the function.

Note
TURBO/QUIET modes are only available when the unit is in cooling or heating mode (not for smart or dry mode). Running the unit in QUIET mode for a long period of time may cause the room temperature to not reach the set temperature. If this occurs, cancel QUIET mode, and set the fan speed to a higher setting.

Requires optional motion sensor part

Smart Focal Point (EFP) will operate the unit at a set point only when the room is occupied.

Evade/Follow
When the iFP sensor is installed the airflow can be set to follow occupants or evade them.

FRESH

1. The FRESH function is valid under the state of ON or OFF. When the air conditioner is OFF, press the “FRESH” button, the display icon on the LCD display to enter Fan mode and low speed. Press the “FRESH” button again, this function is canceled.
2. After the FRESH function is set, ON or OFF functions are kept.
3. After the FRESH function is set, the mode switch function is kept.
4. RESH function is not available for some units. 18. °C/°F function
5. Press “MENU/°F” to toggle between [set temp]°F; [set temp]°C; and 10°C/50°F Low-Temperature Heating mode. Low Temperature
6. Heating is only available when set to HEAT. When set to Low-Temperature Heating, the set point is dropped to a minimum temperature to prevent damage from freezing temperatures.

HEATER

1. When HEAT mode is chosen and is displayed on the LCD display, pressing the “HEATER” button can cancel and set the HEATER function.
2. Auto mode will not start the HEATER function automatically but can set or cancel the HEATER function.
3.  The HEATER function is not available for some units.

Timer

ON-OFF Operation

1. Start the unit and select the desired operating mode.
2. Press the TIMER OFF button to enter TIMER OFF mode.
3. The remote control will start flashing “OFF”, adjusting time with the”+/-” button.
4. once the desired timer is selected for the unit to turn off, press the CONFIRM button to confirm this setting. Cancel
5. TIMER OFF setting: With a TIMER OFF set, press the CANCEL button once to cancel the TIMER OFF.

Note
Holding the “+/-“button down will rapidly adjust the time. After replacing batteries or a power failure occurs, the time setting will need to be reset. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start- Stop or Stop-Start can be achieved. 21. Button +/-: “+” Every time the button is pressed,the time increases 1 minute. “-” Every time the button is pressed, the time decreases by 1 minute. Holding the “+” or “-” button down will rapidly adjust the time.

Clock
Press the “Clock” button, and “AM” or “PM” will flash when the remote is in clock set mode. Use “+/-“ it set mode Use “closed mode. Use M. to adjust the clock and then press “CONFIRM” to exit set mode.

LIGHT
Turns indoor unit display on and off.

RESET
If the remote control is not functioning properly, use a pen point or similar object to depress this button to reset the remote.

LOCK

• Used to lock buttons and LCD display.
• CODE: Function reserved.
• INQUIRE Function reserved

Download PDF:Haier HBS01 AC Remote Control Operating Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>