DURATECH DLD20 LinkDongle User Manual

DURATECH DLD20 LinkDongle

Technical specifications

Box contents

About the DLD20 LinkDongleTM
Manual DLD20 LinkDongleTM The DLD20 LinkDongleTM is an RF module for connecting and controlling the existing Dura Pro or DURA+i heat pumps wirelessly with the LinkTouchTM. The DLD20LinkDongleTM must be connected to the exisiting electronic circuit of the Dura Pro or DURA+i heat pump.

Installation instructions

Power off the heat pump and disconnect from mains! (230 VAC), prior to the installation of the LinkDongleTM

1. Open the top lid
2. Open the electronics lid
3. Find the RS485 cable. It has a black connector and white, yellow, red & black wires. It is marked with yellow tape
4. Connect RS-485 cable from the heat pump to the DLD20
5. Find the terminal block (the power supply to the heatpump)
6. Remove the original spade connectors from the L and N terminals, and put them on the piggyback connectors of the DLD20.
   • Brown = L
   • Blue = N
7. Put the assembled piggyback connectors back on the terminal block
8. Find the SMA antenna connector (inside the electronics compartiment of the heatpump. It will be markedwith yellow tape)
9. Connect the SMA antenna connector with the DLD20
10. Install the DLD20 in the electronics compartment of the heat pump. Make sure none of the connected cables are bent or damaged Location depending on the type of
    • 10a . DURA+i: In the middle of the electronics compartment. You can use cable ties to secure it in placeheatpump:
    • 10b. DURAPRO-12, -17, -21: Tape the DLD20 to the back of the display housing. (Remove the adhesive liner from the back of the DLD20)
    • 10c. DURAPRO-25S, -28TS: Tape the DLD20 to the metal housing of the heatpump. (Remove the adhesive liner from the back of the DLD20)
11. Reassemble the electronics lid
12. Reassemble the top lid
13. Remove the plastic protection cap from the antenna base
14. Screw the antenna onto the antenna base.
15. Make sure the antenna is pointing up

Control functions

See LinkTouchTM for further information on how to pair with the heat pump after installing the DLD20 LinkDongleTM.

Safety information

Intended use

This device has been developed as an RF connecting device for Dura Pro and DURA+i heat pumps and is operated with the LinkTouchTM or controlled by the LinkMasterTM.

Precautions for setup

• The DLD20 LinkDongleTM should only be installed and connected as described in this manual.
• Protect the cables from being strained, pinched or bucked.
• Use only the original cables from the heat pump and DLD20 LinkDongleTM to do the installation.
• Do not use the cables if damaged or frayed. In case of damage, contact an authorized technician for repair.
• The DLD20 LinkDongleTM contains no serviceable parts. Do not attempt to service the DLD20 LinkDongleTM yourself. Repair service should be performed by an authorized technician.

Environment / Disposal of old equipment

This symbol of a crossed out waste bin on a product, its packaging and/or accompanying documents means that the product is subject to the European Directive 2002/96/EC as well as national law for implementation of the directive. Directive and law prescribe that electrical and electronic products must not be disposed of with household waste. The customer must dispose of the product by delivering it to a designated station for collection, treatment and recycling of waste electrical and electronic equipment. The correct disposal of your old appliance is free of charge and will help prevent potential negative consequences of the environment and human health. For more information about disposing your old appliance, contact your city office, waste disposal service, or the shop where you purchased the product.

Service & warranty

If you need service or information or if you have a problem, please contact your local dealer. If needed they will contact the manufacturer to solve your problem. They are gladly willing to assist you! You can find more information at www.duratech.be We warrant all parts to be free from manufacturing defects in materials and workmanship for a period of two years from the date of retail purchase. This warranty is limited to the first retail purchaser and is not transferable. The liability of the manufacturer shall not exceed the repair or replacement of defective parts and does not include any costs for labour to remove and reinstall the defective part, transportation to or from the factory, and any other materials required to make the repair. This warranty does not cover failures or malfunctions resulting from the following:

• Failure to properly install, operate or maintain the LinkDongleTM in accordance with the installation guidelines provided in this manual.
• The workmanship of any installer of the product.
• Abuse, alteration, accident, fire, flood, lighting, rodents, insects, negligence or acts of god.
• Use of non-factory authorized parts or accessories in conjunction with the product.

LIMITATION OF LIABILITY
This is the only warranty given by the manufacturer, No one is authorized to make any other warranties on our behalf. This warranty is in lieu of all other warranties, expressed or imlied, including but not limited to any implied warranty of fitness for a particular purpose and merchantability. We expressly disclaim and exclude any liability for consequential, incidental, indirect or punitive damages for breach of any expressed or implied warranty. This warranty gives you specific legal rights, which may vary, by country.
WARRANTY CLAIMS
For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase, model number, serial number and date of installation. The dealer will contact the manufacturer for instructions regarding the claim and determine the location of the nearest service point.

Regulatory compliance

This product uses radio equipment which fully complies with the European harmonized standards of RED (Radio Equipment Derections) 20/4/53/EC.
Declarations of conformity covering this product are available for download from the House of Duratech website: www.Duratec.be

Contact details
We reserve the rights to change all or part of the contents of this document without prior notice 402-0313-1
Propulsion Systems bv Dooren 72 1785 Merchtem, Belgium
Tel +32 2 461 02 53
www.Duratec.be
info@propulsionsystems.be

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>