DURATECH PLP100-RGB Adagio Pro RGB Light User Manual

June 6, 2024
DURATECH

**DURATECH PLP100-RGB Adagio Pro RGB Light User Manual

**

Technical specifications

Lamp Type Description Voltage Power Nom. Tc Lumen
PLP050-RGB RGB color 50 mm 10-14 VAC 13 W All colors and 650 lm
PLP100-RGB RGB color 100 mm 10-14 VAC 31 W Tunable 1900 lm
PLP170-RGB RGB color 170 mm 10-14 VAC 66 W white 3700 Ern
PLP050-WH Sun White 50 mm 10-14 VAC 8W 5000K 750 lm
PLP100-WH Sun White 100 mm 10-14 VAC 25 W 5000K 2600 lm
PLP170-WH Sun White 170 mm 10-14 VAC 57 W 5000K 5500 Ern
PLP050-WW Warm White 50 mm 10-14 VAC 8W 3300K 700 lm
PLP100-WW Warm White 100 mm 10-14 VAC 23 W 3300K 2400 lm
PLP170-WW Warm White 170 mm 10-14 VAC 55 W 3300K 4950 Ern
PLP050-BL Blue fixed 50 mm 10-14 VAC 8W All colors and 170 lm
PLP100-BL Blue fixed 100 mm 10-14 VAC 25 W Tunable 480 lm
PLP170-BL Blue fixed 170 mm 10-14 VAC 46 W white 1450 lm
PLP050-TW Tunable white 50 mm 10-14 VAC 14 W 2000-99999K 700 lm
PLP100-TW Tunable white 100 mm 10-14 VAC 27 W 2000-99999K 2150 lm
PLP170 -TW Tunable white 170 mm 10-14 VAC 70 W 2000-99999K 4250 lm

For operation only with a safety isolation transformer
IEC Protection Class III

Minimum input voltage: 10 VAC 50 Hz
(at lamp terminals)
Nominal input voltage: 12 VAC 50 Hz
(at lamp terminals)
Maximum input voltage: 14 VAC 50 Hz
(at lamp terminals)
Power factor: > 0,90
Operation on DC voltages is NOT allowed
Maximum water temperature: +40°C Lamps have to be kept out of ice zones
Ingress protection rate: IP68 measured at 3m max depth = 3m

Remarks

Water conditions

Prevent damage to your pool lamps and wires due to unstable water conditions.
Your local government may have enacted guidelines for your pool water conditions to apply by. If not we strongly advise the following parameter specifications to be applied:

pH level: 6,8 – 7,6
Free Chlorine: max. 3ppm
Combined chlorine: max. 1 ppm
Water temperature: max +40°C and lamps need to be kept out of ice zones

Always adhere to the instructions provided by your chemical brand/supplier for the correct use and application of pool chemicals.
Salt water pools, or pools fitted with a salt water chlorine generator contain salt in the pool water. Salt is a corrosive material. Overdosage and/or consistent levels of salt increase the possibility of deterioration of your pool lamps and cables. As a rule of thumb, a concentration of 35gr/l salt can be accepted when pH values are between 7,2-7,4.
In any case, we urge proper use, care and maintenance of your installation, in order to minimize the effect of corrosion and deterioration.
Please be aware that pool lamps and cables with defects caused due to abnormalities in the water condition are not covered by our factory warranty

Installation/maintenance

The luminaire is maintenance free
If the luminaire needs to be replaced, it needs to be completely removed from the water

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid hazard

Box contents

ADAGIOPRO Lamp (50,100 or 170 mm)

Connection Kit ADAGIOPRO ( 513-0152 or 513-0219 )

4m Cable
Product Components
Manual

Retrofit Kit (only for 170mm models)
Product Components

Installation instructions

mounting face plate
Installation instructions
mounting the connector
Installation instructions

Connector installation

Connector installation Connector
installation Connector
installation Connector
installation Connector
installation Connector
installation

Wiring instructions Setup 1

For new installations
Each lamp is connected to the transformer by a separate cable
Wiring instructions
4m cable included in lamp package Separate cable ( not included )

Always use a toroïdal transformer
We recommend using 2 CORE cables for all Adagio Pro lights

SELECT CABLE SECTION & MAXIMUM LENGTH

| LAMP TYPE| 1,5mm2| 2,5mm2| 4,0mm2| 6,0mm2| 10mm2| | VA TRANSFORMER
(12VAC)*
---|---|---|---|---|---|---|---|---
| | | | | |
| PLP050-WH
PLP050-WW
PLP050-BL
PLP050-RGB / TW| 95m
55m| 160m
90m| 250m
145m| 350m
200m| 600m
350m| 10 VA
18 VA
| | | | | |
| PLP100-WH
PLP100-WW
PLP100-BL
PLP100-RGB / TW| 30m
20m| 50m
40m| 80m
65m| 120m
95m| 200m
165m| 33 VA
40 VA
| | | | | |
| PLP170-WH
PLP170-WW
PLP170-BL
PLP170-RGB / TW| 12m
10m| 20m
15m| 35m
25m| 50m
40m| 90m
70m| 74 VA
91 VA

STABLE OPERATION OF THE POOL LIGHTS IS ONLY GUARANTEED WHEN THE INSTALLED CABLE CROSS SECTION MATCHES OR EXCEEDS THE ADVISED VALUES IN THE ABOVE TABLE

    • The transformer VA rating must be greater or equal to the sum of VA ratings of all connected lamps.
      These cable lenghts are calculated with worst case voltage drops in the electrical wiring.
Wiring instructions Setup 2

For existing or other installations

All lamps are connected to the transformer via 1 cable

Wiring instructions
4m cable included in lamp package Separate cable ( not included )

We recommend using 2 CORE cables for all Adagio Pro lights
This setup is not preferred for installations where DURALINK connected products are used
) PLP-REM, PLP-REM-300/350, LinkTouch, DLM-450, DLM-600

SELECT CABLE SECTION & MAXIMUM LENGTH

| | ILAMP TYPE| QTY| 2,5mm2| 4,0mm2| 6,0mm2| 10mm2| VA TRANSFORMER
(12VAC)
---|---|---|---|---|---|---|---|---
| | | | | | |
| | PLP050-WH PLP050-WW PLP050-BL| 1| 160m| 250m| 350m| 600m| 10
2| 80m| 125m| 175m| 300m| 20
3| 53m| 83m| 117m| 200m| 30
4| 40m| 63m| 88m| 100m| 40
| | PLP050-RGB / TW| 1| 90m| 145m| 200m| 350m| 18
2| 45m| 73m| 100m| 175m| 36
3| 30m| 48m| 67m| 117m| 54
4| 23m| 36m| 50m| 88m| 72
| | | | | | |
| | PLP100-WH PLP100-WW PLP100-BL| 1| 50m| 80m| 120m| 200m| 33
2| 25m| 40m| 60m| 100m| 66
3| 17m| 27m| 40m| 67m| 99
4| 13m| 20m| 30m| 50m| 132
| | PLP100-RGB / TW| 1| 40m| 65m| 95m| 165m| 40
2| 20m| 33m| 48m| 83m| 80
3| 13m| 22m| 32m| 55m| 120
4| 10m| 16m| 24m| 41m| 160
| | | | | | |
| | PLP170-WH PLP170-WW PLP170-BL| 1| 20m| 35m| 50m| 90m| 74
2| 10m| 18m| 25m| 45m| 148
3| 7m| 12m| 17m| 30m| 222
4| 5m| 9m| 13m| 23m| 296
| | PLP170-RGB / TW| 1| 15m| 25m| 40m| 70 m| 91
2| 8m| 13m| 20m| 35m| 182
3| 5m| 8m| 13m| 23m| 273
4| 4m| 6m| 10m| 18m| 364

STABLE OPERATION OF THE POOL LIGHTS IS ONLY GUARANTEED WHEN THE INSTALLED CABLE CROSS SECTION MATCHES OR EXCEEDS THE ADVISED VALUES IN THE ABOVE TABLE

Wiring remarks

For installations with DURALINK* products

  1. Third party equipment such as frequency inverters and electric motors can generate excessive noise on the 230VAC / 400VAC power line.
    This noise might be injected into the adjacent 12VAC power line and disturb the power line communication towards the AdagioPro RGB lights.
    Keep 230VAC / 400VAC power line cables at least 50cm separated over their full length from the 12VAC power line towards any RGB lights
    Do not mix 12VAC and 230VAC / 400VAC power line cables into the same ! cable trays

  2. Floating cores in a multi-core cable are not allowed because it disturbs PLC communication.
     We recommend using 2 CORE cables for all Adagio Pro lights to avoid PLC communication issues

() Do not mix 12VAC and 230VAC / 400VAC power line cables into the same cable trays
Diagram
**

Retrofit in PAR56 niche (only PLP170)

Company
Product Company
Product

Color programs

Color Programs

RGB LAMPS

  1. DEEP BLUE SEA: Saturated blue
  2. DAYLIGHT BLUE: Light blue
  3. SUNSET: Slow animation orange – red
  4. LOVE IS IN THE AIR: Red
  5. FOREST SPRING: Green
  6. THINK PINK: Pink
  7. SUNSHINE: Yellow
  8. JUNGLE BEACH: Slow animation blue & green tints
  9. VOODOO: Slow animation red & purple tints
  10. DISCO: Fast animation lila-pink-peach-yellow-green blue
  11. PARTY: Fast animation blue-green-red-pink-yellow-green
  12. WARM WHITE: 3000K
  13. NEUTRAL WHITE: 6000K
  14. SUN WHITE: 10.500K
    fixed colors
    dynamic colors
    white tints

TW LAMPS

7 white tints

  1. 3200K
  2. 3800K
  3. 5400K
  4. 7300K
  5. 14800K
  6. LIGHT BLUE
  7. BLUE
  • all color programs are dimmable if PLP-REM,PLP-REM-350, LinkTouch, DLM 450 or DLM-600 are used (in PLC mode)

Synchronizing & color changing (for RGB and TW lamps only)

Manual synchronization

  1. Switch ON the 12 VAC line voltage and make sure that all lamps light up.
  2. Switch OFF the 12 VAC line voltage and wait for at least 20 sec.
  3. Switch ON and switch OFF
  4. Switch ON and switch OFF
  5. Switch ON
  6. The lamps should now all be on color program 1
    for RGB lamps: fixed blue light (Deep blue Sea)
    for TW lamps: 3200K

Changing colors

Quickly turn the lamps OFF and back ON
The lamp will jump to the next color program ( 1 –> 14 )

Memorizing the last color
Turn the lamp OFF for MINIMUM 20 seconds
The last chosen color has now been memorized

The use of PLP-REM, PLP-REM-350, LinkTouch, DLM-450 & DLM-600 control units enables extended features like automatic synchronisation, dimming and DMX / RS485 control

Troubleshooting

PROBLEM

|

SOLUTION

---|---

  • The pool light is flickering

|

  1. Switch the lamps ON For RGB lamps: select the Sun White color program
  2. Remove the lamp from the water, unscrew the clips nut, pull back the gasket and the black cable jacket, so you can reach the brass contacts inside the connector block (do not remove the connector block)
  3. Measure the voltage at the lamp terminals (while the lamp is still ON)
  4. The voltage at the lamp should be at least 10VAC 50/60hz. If the measured line voltage is below 10VAC:
    A. Check the output voltage at the transformator terminals. This voltage should be between 12VAC and 14VAC. Verify that the used transformator VA rating is sufficient for powering all connected lamps
    B. If the transformator output voltage is ok, then install a thicker cable between the transformator and the lamp. (wiring instructions)
  • Several pool lights in the pool show different color programs

| Make sure that all lamps are connected to the same 12VAC power line. Execute the synchronization

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals