Sangcon B08HMNDNDQ 5 In 1 Countertop Blenders for Kitchen with Strainer Instruction Manual

Sangcon B08HMNDNDQ 5 In 1 Countertop Blenders for Kitchen with Strainer

Caution

1. Please read the instruction carefully before use.
2. Before connecting to the appliance, make sure the local voltage matches the voltage shown on the rating label.
3. Do not allow children or handicapped people to play with the machine.
4. Please operate the machine according to the stated interval time. Do not overload the machine.
5. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or similarly qualified persons in order to avoid a hazard.
6. The blade is very sharp, pay attention not to hurt your hand when cleaning and disassembling the machine.
7. Blade components and mixing cup should be fully tightened, do not remove the seal ring, otherwise, it will cause leak­age or blade component to come off.
8. Do not use the blade components working on the host directly. Also do not touch rotating components when working.
9. Ensure the lid is covered before operating.
10. Before turning on the power, do not put the finger or any other tools into the jug.
11. The processing temperature of food should not exceed 60 °C. Do not operate the machine continuously more than 1 min, ensure that machine is let to cool down before repeat use.
12. The processing capacity of food should not exceed 1000ml.
13. There is an overheat protection function, if it’s too hot while operating, the machine will stop working. Immedi­ately turn off the power, do not use until the main engine cool again.
14. Do not contact the machine motor with water to avoid any hazard that may cause the machine to malfunction.
15. The machine is only suitable for home use only.

Main Parts

• Chopper cover
• Lid
• Low cup
• ChopQer blade
• Big jar cover
• Flat blade
• Chopper bowl
• Filter
• HIGH CUP
• Gearbox
• Big jar
• Main engine
• Cross blade

Main technical parameter

• Model: SK008-3B
• Voltage: AC120V,…, ,60Hz
• Power: 350W

Operation Method

Blending

1. Put the machine on a stable table
2. Fix the cross blade to the bottom of the jug
3. inject the right amount of water into a jug, then put in the diced vegetable. Attention: processing capacity of food should not exceed 1 000ml( or not more than 2/3 capacity)
4. Put on the cover, then tighten it clockwise
5. Put the blending cup on the main body and be sure the upper concave parts fix well to the convex parts on the bottom of the cup, then tighten it clockwise
6. Plugin the machine into AC120V,…,
7. Choose the right speed, if blending some hard food, please kindly choose the second speed. Normally, it is finished within 1 min.
8. After blending, turn the switch back to zero speed. The machine stops working, then pull out the plug, pour the food out.
9. Repeat the steps if reuse is desired.

Soy-bean milk making

1. Soak the soybean into the water for 8 hours
2. insert the filter down the center of the cup, making sure to line the three notches up with the three ribs inside of the blending cup.
3. Twist the cross blade onto the bottom of the blending cup.
4. Add some water to the blending cup and the soaked soya beans on the lid. Measure the beans by using the lid, and never add beans more than one and half cups. After which, fix the lid on the cover of the cup.
5. Plug in and turn on the switch. When the machine works regularly, it can finish the soybean milk making in 1 minute.
6. Pour out the soybean milk and the residue left in the filter naturally.
7. Boil the pre-processed soybean milk, then it can be consumed instantly.

Grinding

1. Put the food in the low cup, making sure it does not exceed 1 00g.
2. Twist the flat blade on the bottom of low cup and fix it on the main body.
3. Power the plug, choose the second speed, the machine starts to grind, it is finished within 30 seconds.

Chopper

1. Inserted “S” blade into drive shaft of the container, make sure in the right place.
2. Clean the meat (pork, beef), then de-bone, peel off, muscle off. Then cut into the 2cm*2cm small pieces. Putting into the container. Attention: processing capacity of food should not exceed 2/3 capacity.
3. Put on the cover, then tighten it clockwise
4. Fix the container components to the main machine 5.
5. On the power, choose the second speed, the machine starts to chop, it is finished within 1 min. It is not availa­ble to chop too long, to ensure the meat is fresh.
6. After chopping, turn the switch back to zero speed, also plug off, take out the container components, open the cover, take out the food.
7. Repeat the steps if desired for the next use.

Clean and maintain

1. ln case of electric shock, you must be sure the machine is powered off when cleaning the body.
2. Clean the main body using a wet cloth instead of water.
3. Do not wash the machine with a dish washer.
4. lt can be used again once you clean up the parts and assemble them well.
5. Some parts may have discoloration over a period of usage.
6. The machine should be used often, otherwise place in a dry and ventilated environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>