thePondguy 160192 ClearVac Dual-Chamber Pond Vacuum Owner’s Manual

ClearVac TM
Dual-Chamber Pond Vacuum Installation & Maintenance Manual
(Item # 160192)
3 Year Warranty

IMPORTANT INFORMATION:

Please read these instructions thoroughly before use. Failure to follow instructions may result in equipment damage or failure, losses, injury or death.

DANGER:

• To avoid possible electric shock:
• If the power cord has been damaged, DO NOT operate, the ClearVacTM Vacuum should be replaced.
• Prior to installation, inspect the ClearVacTM Vacuum to ensure there was no damage during transportation.
• If the ClearVacTM Vacuum falls into the water, DO NOT reach for it. First, unplug and then retrieve it.
• Close supervision is necessary when used near children.

WARNING:

• To reduce the risk of electric shock:
• Connect only to a properly grounded receptacle, which is serviced by a Ground Fault Circuit Interrupter and never remove the ground pin from the plug.
• Provide a “drip loop” for the power cord.
• This is a loop in the cord below the level of the receptacle or plug that prevents water from traveling along the cord in the direction of the receptacle.
• ALWAYS unplug the ClearVacTM Vacuum from the power source when it is not in use, and before installing, removing, or servicing the ClearVacTM Vacuum components.
• If an extension cord is necessary, use only a 10 or 12 gauge outdoor-rated extension cord no longer than 50 feet. A cord may overheat if the cord is rated for fewer amperes or watts than the unit rating.
• DO NOT immerse the ClearVacTM Vacuum or plug in water or attempt to use a wet plug.
• The ClearVacTM Vacuum is NOT suitable for use in swimming pools, swimming ponds, or other situations where bodily contact is made with the water. Although the ClearVacTM Vacuum is designed for outdoor use, it should never be submerged in water.

CAUTION:

• To reduce the risk of equipment damage or failure:
• DO NOT place ClearVacTM Vacuum near flammable or other dangerous materials or objects.
• ClearVacTM Vacuum is NOT submersible; do not place ClearVacTM Vacuum where it might contact or fall into the water.
• DO NOT operate during freezing conditions. Drain the ClearVacTM Vacuum and store it in a protected location.
• DO NOT use the ClearVacTM Vacuum to vacuum flammable, toxic, or volatile substances.
• Be sure to clean debris from the vacuum after each use, and before storing the unit, to avoid poor performance during future use.

IMPORTANT:
The Pond Guy® is not responsible for equipment damage or failure, losses, injury, or death resulting from failure to follow safety precautions, misuse or abuse of equipment.

Package Contents CLEARVACTM:

Note: Some of the components may be packaged inside the vacuum chamber

 D 4 – Interchangeable Nozzles
(String Algae, Narrow, Wide & Adjustable Gravel Nozzles)| I 2 – Wheels
E 1 – Debris Bag| J 1 – Intake Distributor

TECHNICAL SPECS:

ASSEMBLY INSTRUCTIONS CLEARVACTM:
See video instructions of the ClearVacTM vacuum online @ www.thepondguy.com/clearvac
Step 1
Unlock the Chamber
Remove stored parts from the collection chamber by unlocking the vacuum chamber clamps and removing the top of the vacuum. Replace the vacuum top and lock the clamps back into place. Step 2
Attach Wheels
Attach the wheels to the rear base of the ClearVacTM. Step 3
Attach Intake Distributor
Attach the intake distributor to the intake opening and twist to lock it into position. Step 4
Connect the Suction Hose
Connect the suction hose to the intake distributor.

Step 5
Connect the Discharge Hose
Connect the discharge hose to the drain opening located towards the bottom of the unit.

Step 6
Position the Discharge Hose
Lay the discharge hose so it lies flat and away from the pond. If desired, attach the debris bag to the end of the discharge hose by placing the end of the hose in the debris bag and tightening the drawstring.

Note: The debris bag will collect only larger debris for disposal. We do not recommend returning water to the pond from the discharge hose, as it may result in cloudy water.
Step 7
Attach the Extension Tubes
Attach extension tubes to the suction hose. The clear extension tube will allow you to monitor the ClearVacTM performance. Step 8
Choose a Nozzle
Attach one of the four interchangeable nozzles to the extension tube:

• String Algae Nozzle
• Narrow Nozzle for hard to reach places
• Adjustable Gravel Nozzle great for cleaning ponds with gravel bottoms
• Wide Nozzle for large areas

String Algae Nozzle|
---|---
Narrow Nozzle|
Adjustable Gravel Nozzle|
Wide Nozzle|

USING THE CLEAR ACT VACUUM:
Step 1
Position the Vacuum
Position the ClearVacTM near the edge of the pond and plug it into a GFCI outlet. The ClearVacTM can be used with an extension cord but it must be a 10 or 12 gauge outdoor-rated extension cord no longer than 50′. Step 2
Turn on the Vacuum
Turn the power switch to the “ON” position and submerge the end of the suction hose in the pond.

Step 3
Adjust the Suction
Using the vacuum level adjustment on the handle of the suction hose, slowly close the valve to increase the suction and lift unwanted debris.

Step 4
Vacuum Debris
Move in a slow, uniform fashion to remove sludge, debris, and algae. When the reservoir becomes full, the ClearVacTM will automatically switch reservoirs and drain allowing for continuous vacuuming. Step 5
Turn Off the Vacuum
When finished, turn the power switch to the “OFF” position and unplug the ClearVacTM. Be sure to clean the unit after each use before storing.

MAINTENANCE:

WARNING:
Before performing any maintenance, always unplug the ClearVacTM from the power source.

• Clean the collection chamber, tubes, and foam filters after operating and rinse with clean water.
• Check o-rings and foam filters for wear or damage and replace if needed.

STORAGE:

• The ClearVacTM hoses and extensions easily disassemble and can be stored right on the unit.
• The ClearVacTM includes a handle for easy mobility. Simply unthread the tension knob, adjust the handle and retighten.
• The ClearVacTM should be stored in a dry, temperature-controlled room.

TROUBLESHOOTING:

WARNING:

For your protection, always unplug the ClearVacTM from your power source before servicing.
Little or no suction is produced:

• Be sure the ClearVacTM is positioned at or near water level.
• Remove and inspect the intake distributor, intake, and suction hoses for obstructions.
• Reduce the number of extension tubes used
• Be sure the suction hose is lying as flat as possible with no kinks.
• Check to be sure that o-rings are installed properly.

The unit does not reach full capacity or the collection chamber does not drain:

• Clean foam filters
• Remove and inspect the intake distributor, intake, and suction hoses for obstructions.
• Check for kinks in discharge hose, lay discharge hose flat or at a slight decline to aid in draining.
• Check drain opening for blockages

The unit develops noise or heavy vibration: Turn the power switch off for 20 seconds and then restart the unit. If issue persists try the following:

•  Make sure the collection chamber is not full and that it is draining properly
• Clean foam filters
• Remove and inspect the intake distributor, intake, and suction hoses for obstructions.

Vapor escapes from the unit:

• In cold weather, condensation forms in the unit and it is released as water vapor. This is normal and no remedy is necessary.

REPLACEMENT PARTS:

WARRANTY:

All ClearVacTM Vacuums carry a 3-year warranty. The Pond Guy® will repair or replace any units found to be defective. This limited warranty is extended exclusively to the original purchaser and begins from the date of the original purchase receipt. The filter foam and o-rings are wearable items and are not covered by this warranty. Abuse or misuse of this product, power cord alterations, or use of an improper extension cord voids all warranty. Please call for a Return Authorization Number prior to returning the product by calling our Customer Care Department at 866-766-3435. Failure to request an RMA number may result in delay or dismissal of your warranty claim.

THANK YOU FOR CHOOSING:
The Pond Guy® Inc.
We Know PondsTM 15425 Chets Way Armada, MI 48005
866-POND-HELP (766-3435) thepondguy.com
View other great products online at www.thepondguy.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>