SALUS 091FLRF Wireless Room Thermostat User Guide

: June 6, 2024
: SALUS

SALUS 091FLRF Wireless Room Thermostat

Introduction

091FL/091FLRF is a programmable, weekly thermostat used to control room temperature in heating or cooling systems. Before use please read this manual carefully. Use only AA 1.5V alkaline batteries in the thermostat. Place the batteries into the battery slot located under the cover. Do not use rechargeable batteries.

Product Compliance

This product complies with the following EU Directives:
091FL: 2014/30/EU, 2014/35/EU, 2011/65/EU

Safety Information

Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Installation must be carried out by a qualified person in accordance with national and EU regulations.

Proper Thermostat Placement

Technical Specification

Wired Thermostat 091FL

Power supply	2 x AA batteries
Rating max	5 (3) A
Sal	Voltage-free NO/COM relay
Temperature range	5 – 30°C

Button Functions

SUN
Comfort temperature or changing parameters up
MOON
Economic temperature or changing parameters down
D
Set the day of the week
H
Set the hour
M
Set the minutes
Temp
Temperature setpoint
Prog
Weekly programming
Prog #
Program selection
OK
Confirm function
Reset
Factory Reset

LCD Icon Description

Day of the week indicator
Heating Mode ON
Cooling Mode ON
Room / Setpoint Temperature
Temperature unit
Controlled device working status (e.g. boiler)
Temporary override
Eco Mode
Program number
Antifrost Mode
Comfort Mode
Program timeline indicator
Clock
Low battery indicator
AM/PM

091FL Wiring Diagram

091FLRF Wiring Diagram

CHANGING THE COMMUNICATION CODE OF 091FLRF
Note: To prevent interference from other wireless devices it is recommended to change the communication code from factory setting.

Use DIP switches (numbered 1-5) to change the communication code.
$Use DIP switches $numbered 1-5$ to change the communication code$
Set DIP switches randomly – they need to be in the same position on both the receiver and the transmitter.
Press Reset button after communication code changing.

Setting Time

Press OK button to highlight the display.
Press D to set the day.
Press H to set the hour.
Press M to set the minutes.

Setting the Comfort Temperature

Press OK button to highlight the display.
Press and then press Temp.
Display will show current comfort temperature.
To change this temperature, press SUN or MOON icons button.
To confirm press OK button.

Setting the Economic Temperature

Press OK button to highlight the display.
Press Moon and then press Temp.
Display will show current economic temperature.
To change this temperature, press Sun or Moon button.
To confirm press OK button.

Programs

Setting the comfort temperature 03

Comfort Temperature

There are 9 programs available. Programs 0-5 are factory programs. Programs 6-8 can be defined by user.

Selection of Factory (0-5) Programs

Press OK to highlight the display.
Press Prog # to set the program number (0-5) for the selected day.
Program 0 is a special program. It will set the thermostat to antifrost temperature (7°C) for the full day.
$Selection of factory $0-5$ programs$
To confirm press OK button.

Choosing and Programing (6-8) User Programs

Press OK button to highlight the display.
Select the day of the week by pressing Prog button.
Press Prog # to set the program number (6,7 u 8) for the selected day.
$Choosing and programing $6-8$ user programs$
Press Sun or Moon button (each pressing one of these buttons moves the timeline by one hour and assigns a comfortable or an economic temperature).
To confirm press OK button.

CHANGE COOLING / HEATING

Press OK button to highlight the display.

Heating mode – the relay closes the contacts when there is a need for heating (default setting).
Cooling mode – the relay closes the contacts when there is a need for cooling (with 5 minutes delay).
Press Sun or Moon to select mode.
To confirm your option press OK.
DLYOFF Heating device delay switch disabled (default setting).
DLYON Heating device delay switch is ON (5 min).
Select by pressing Sun or Moon button.
To confirm your option press OK.
SPAN Temperature span selection, possible values are 0.5°C or 1.0°C (default = 1.0°C).
Press Sun or Moon to set span.
To confirm your option press OK.
OFF5 Measured temperature correction*
(value range: -3.0°C to + 3.0°C, default = 0.0°C).
Press Sun or Moon to set correction.