HOLLYLAND LARK C1 Solo Wireless Microphone System User Manual
- June 4, 2024
- HOLLYLAND
Table of Contents
- HOLLYLAND LARK C1 Solo Wireless Microphone System User Manual
- LARK Cl
- PACKING LIST
- PRODUCTION INTRODUCTION
- PRODUCTION INSTALLATION
- PRODUCTION FUNCTION
- PRODUCTION FUNCTION
- PARAMETERS
- SUPPORT
- Note:
- Safety Precautions
- FCC Requirement
- FCC Radiat ion Exposure Statement:
- Note:
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HOLLYLAND LARK C1 Solo Wireless Microphone System User Manual
LARK Cl
- The quantity is based on the product’s various model and is subject to the actual quantity of equipment purchased.
PACKING LIST
LARK C1 SOLO [JX•1 to RX•1J Wireless Microphone System
• The quantity is based on the product’s various model and is subject to the actual quantity of equipment purchased.
LARK DUO (JX•2 to RX•1) Wireless Microphone System with Charging Case
• The quantity is based on the product’s various model and is subject to the actual quantity of eciuipment purchased.
PRODUCTION INTRODUCTION
PRODUCTION INSTALLATION
-
The TX (transmitter) automatically turns
-
Connect the RX to the smartphone. Q
-
Charge the Smartphone via the RX. on when takes it out from the charging case. Simply clip the TX (transmitter) to a shirt collar.
PRODUCTION FUNCTION
- ♦ Blue LED Stays On Device disconnected HaarC lear(Noise RedLKJtion) Off by default
♦ Green LED Stays On HearClear(Noise Reduction) ON Pfoos the TX’a yel,oN Moo to t llfl oo the~ Aedi..clirn) ll.rlctlon,l'<‘hooactMJ:to:J,tt,c rdcata”lffitln15groo:,
♦ LED Flashing: Charging
♦ LED Stays On: Ful~ charged
Ona Light Flashing • o o o 25% Two Ughts Flashing e e O O 50% Three Ught s
Flashing • • • o 75% Four Lights Flas hing • • • • 100%
PRODUCTION FUNCTION
Manual Pairing
Mer the recerver Is connected to the smartphone, long press lX’s ‘raV¼’ button for 3s and then long press RX’s ·m:J’ for 3s paJrlng.
- The device has been paired in the factory before shipping. The product needs to pair againwhen there is disconnection,
PARAMETERS
SUPPORT
If any problems are encountered using the product, please follow these options for receiving technical support:
Note:
The frequency range and wireless transmit power of the device vary based on theregulations of different countries and regions.
Safety Precautions
Do not place the product near or inside heating devices (including but not
limited to microwave ovens, induction cookers, electric ovens,electric
heaters, pressure cookers, water heaters, gas stoves) to prevent the battery
from overheating and exploding. Never use non-original charging
cases,cables,and batteries with the product.
The use of non-original spare parts may cause electric shock, fi re,
explosion, or otherdangers.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the fo
llowing two conditions:
(1)this device may not cause harmful interference.
(2)this device must accept any interference received , including interference
that may cause undesired operation.
FCC Radiat ion Exposure Statement:
The device has been tested and comply with FCC SAR limits.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installat ion.
This equipment generates, uses, and can radiate rad io frequency energy, and
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If th is
equipment does cause harmful interference to radio or television reception,
which can be determined by turn ing the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
fo llowing measures:
- Reorient or re locate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced rad io/TV technician for help.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>