beamZ 153.685 Derby Strobe User Guide

June 6, 2024
beamZ

beamZ 153.685 Derby Strobe - 2

153.685 V1

DERBYSTROBE

QUICK START GUIDE

RIGGING

The unit may be set up on a stable and even surface. By means of the fixing facilities of the baseplate, the unit can also be mounted upside down to a truss, see below picture. For fixing, certified clamps with correct save working load are required. According to the figure, the quick lock bolts of the omega brackets are placed into the openings provided in the base plate and turned clockwise until they lock (to the stop). The mounting place must be of sufficient stability and be able to support a weight of 10 times of the unit’s weight. Secure the unit with a safety cable so that it cannot fall down.

When carrying out any installation, always comply European and national guidelines concerning rigging, truss and all other safety issues. Always let the installation checked out by an authorized dealer !

beamZ 153.685 - Rigging 1      beamZ
153.685 - Rigging 2

  1. SAFETY CABLE
  2. TRUSS CLAMP
REMOTE CONTROLLER

beamZ 153.685 - Remote Control

BLACK OUT MODE
Press < BLACK OUT > off existing modes. Press < BLACK OUT > return the last modes.

AUTO MODE
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:
1. Press < AUTO> on the remote controller.
2. Press < +> or < -> to choose between the different auto programs.

SOUND MODE
Sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:
1. Press < SOUND> on the remote controller.
2. Press < +> or < -> to choose between the different sound programs.

STROBE MODE
To adjust the strobe speed of the automatic program and the sound active program.
1. Press < STROBE> on the remote controller.
2. Press < +> or < -> to either increase or decrease the speed of the program.
3. Press < STROBE> again to turn off the strobe.

SPEED MODE
To adjust the speed of the automatic program and the sound active program.
1. Press < SPEED> on the remote controller.
2. Press < +> or < -> to either increase or decrease the speed of the program.

SENSITIVITY MODE
To adjust sound sensitivity for in Sound-Active mode
1. Press < SENSITIVITY> on the remote controller.
2. Press < +> or < -> to either increase or decrease sound sensitivity.

DMX / % MODE
To enable DMX or disallow DMX on the product.
Press < DMX> on the remote controller, the product work on the DMX controlling modes.

MANUAL MODE
1. Press < MANUAL> on the remote controller.
2. Press < R>, , , , (red, green, blue or white) to choose your colour.
3. Press again < R>, , , , (red, green, blue or white) to close your colour.
4. Press < +> or < -> to either increase or decrease the percentage of each colour.

  CAUTION! The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote control. Otherwise operation of the remote control is not possible.

beamZ 153.685 - Replac battery

If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press the small bar with the groove to the right (1) and at the same time remove the battery support (2). For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.

DMX CHANNELS
CHANNEL FUNCTION VALUE DESCRIPTION
1 Strobe 000-255 Stroboscope (Rate 0-100%)
2 Colour 000-009 No function
010-019 Red
020-029 Green
030-039 Blue
040-049 White
050-059 Red+ Green
060-069 Red+ Blue
070-079 Red+ White
080-089 Green+ Blue
090-099 Green+ White
100-109 Blue+ White
110-119 Red+ Green+ Blue
120-129 Red+ Green+ White
130-139 Red+ Blue+ White
140-149 Green+ Blue+ White
150-255 Red+ Green+ Blue+ White
3 Rotation 000-159 Motor rotation angle
160-255 Motor Auto program (Rate 0-100%)
4 SMD Strobe 000-009 No function
010-159 SMD Strobe (Rate 0-100%)
160-255 SMD Auto program (Rate 0-100%)
5 Mode 000-009 No function
010-019 Auto Program 1
020-029 Auto Program 2
030-039 Auto Program 3
040-049 Auto Program 4
050-059 Auto Program 5
060-069 Auto Program 6
070-079 Sound Program 1
080-089 Sound Program 2
090-095 Sound Program 3
100-109 Sound Program 4
110-119 Sound Program 5
120-255 Sound Program 6
6 Speed 000-255 Auto and Sound program speed (Slow-fast)

beamZ 153.685 Derby Strobe - 3

beamZ logo m1

is a leading developer of lighting products, including intelligent DMX moving heads, wireless battery operated DMX effects, static washes, sound-activated club effects, strobes & blacklights, LED lighting, fog and special effects machines, lasers and indoor and outdoor architectural lighting, as well as lighting controllers and protective bags.

BEAMZLIGHTING.COM

Documents / Resources

| beamZ 153.685 Derby Strobe [pdf] User Guide
153.685, Derby Strobe, 153.685 Derby Strobe
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals