EIBENSTOCK AEND 40 A Diamond Wet Core Drilling Instruction Manual
- June 12, 2024
- EIBENSTOCK
Table of Contents
- EIBENSTOCK AEND 40 A Diamond Wet Core Drilling
- Product Information
- Product Usage Instructions
- Important Instructions
- Technical Data
- Supply
- Application for Indented Purpose
- Safety Instructions
- Commissioning
- Switching on and off
- Water Supply
- Drilling
- Drill Bit Changing
- Care and Maintenance
- Noise / Emission
- Warranty
- EU Declaration of Conformity
- Declaration of Conformity
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EIBENSTOCK AEND 40 A Diamond Wet Core Drilling
Product Information
Technical Data
- Rated voltage: 18 V
- No-load speed: 0 – 8000 min-1
- Collet: M 12 x 1,5
- Max. drilling diameter – dowel holes: 20 mm
- Weight (without battery): ca. 1.7 kg
- Weight (with battery): ca. 2.4 kg
- Order number with battery and charger: 030A1000
- Order number without battery and charger: 030A2000
Supply
- Available add-ons:
1. **Order number:** 37731000
2. **Order number:** 37734000
3. **Order number:** 37732000
4. **Order number:** 35910000
Application for Indented Purpose
Attention! Only use original EIBENSTOCK drill bits. They were especially
developed for the END 40 A, have a high concentricity and work very
effectively. In case of using other drill bits, we cannot assume any
liability!
Safety Instructions
Safe work with this machine is only possible if you read this operating
instruction completely and follow them strictly. Additionally, the general
safety instructions of the leaflet supplied with the tool must be observed.
Prior to the first use, the user should absolve a practical training. Save all
warnings and instructions for future reference.
Product Usage Instructions
Important Instructions
Important instructions and warning notices are allegorized on the machine
by means of symbols:
- Before you start working, read the operating instructions of the machine.
- Work concentrated and carefully.
- Keep your work-place clean and avoid dangerous situations.
- In order to protect the user, take precautions.
Safety Precautions
During work you should:
- Wear goggles
- Wear ear protectors
- Wear protective gloves
- Wear protective boots
Operating Instructions
- Transport of Li-Ion battery packs: The shipping of Li-Ion battery packs is subject to dangerous goods regulations.
- To turn on/off the machine, follow the instructions provided.
- To change the drill bits, follow the instructions provided.
Environmental Protection
Typical values:
- Sound pressure level (LwA): 75 dB(A)
- Sound power level (LpA): 86 dB(A)
- Uncertainty (K): 3 dB
- Vibration emission value (ah): 2.7 m/s²
- Uncertainty (K): 0.3 m/s²
Contact Information
Frank Markert
Head of Engineering
Important Instructions
Important instructions and warning notices are allegorated on the machine by means of symbols:
- Before you start working, read the operating instructions of the machine.
- Work concentrated and carefully. Keep your work-place clean and avoid dangerous situations.
- In order to protect the user, take precautions.
During work you should wear goggles, ear protectors, protective gloves, and water proofed working clothes!
- Wear ear protectors
- Wear goggles
- Wear protective gloves
- Wear protective boots
Technical Data
Battery-Diamond Wet Drill END 40 A
Rated voltage: | 18 V |
---|---|
No-load speed: | 0 – 8000 min-1 |
Collet: | M 12 x 1,5 |
Max. drilling diameter – dowel holes:
– tile / panel drilling (max. 20mm thickness)| 20 mm
40 mm
Weight (without battery): Weight (with battery):| ca. 1.7 kg
ca. 2.4 kg
Order number with battery and charger:
without battery and charger| 030A1000
030A2000
Supply
Battery-diamond wet drill incl. water pressure tank, side handle with depth
stop, tool for mounting the drill bits, adapter M12x1,5 fm / ½” fm, battery
18V / 5,2 Ah, battery charger and operating instructions in a plastic case.
Available add-ons:
Article | Order number |
---|---|
Li-ion-battery 18V / 5,2 Ah | 37731000 |
Battery charger standard (loading time ca. 110 min) | 37734000 |
Quick charger (loading time ca. 45 min) | 37732000 |
Centring device with drilling template | |
Diamond full drill bits (length: 60 mm) | |
M 12 x 1,5; Ø 6 – 12 mm | |
Diamond hollow drill bits (length: 60 mm) | |
M 12 x 1,5; Ø 6 – 12 mm | |
Diamond full drill bits (length: 150 mm) | |
M 12 x 1,5; Ø 6 – 12 mm | |
Diamond – wet – drill bits ½“m Ø 22-40mm | |
Sharpening block | 35910000 |
Application for Indented Purpose
Together with special wet drill bits, the END 40 A is made for drilling tiles, granite, marble, natural stone etc. from 3.5–40 mm diameter.
Attention!
Only use original EIBENSTOCK drill bits.
They were especially developed for the END 40 A, have a high concentricity and
work very effectively.
In case of using other drill bits, we cannot assume any liability!
Safety Instructions
Safe work with this machine is only possible if you read this operating
instruction completely and follow them strictly. Additionally, the general
safety instructions of the leaflet supplied with the tool must be observed.
Prior to the first use, the user should absolve a practical training. Save all
warnings and instructions for future reference.
When drilling in ceilings or walls make sure you will not cut through
electrical mains, gas or water pipes. Use metal detection systems if needed.
Before you start working consult a statics expert to determine the exact
drilling position.
The tool must neither be wet nor used in humid environment.
- Do not use the tool near explosive materials.
- Do not work with materials containing asbestos
- Modifications of the tools are prohibited. After an interruption of work the drill machine should only be switched on again if the drill bit can be turned easily.
- Do not use the machine when one part of the housing is damaged or in case of damages on the switch.
- Electric tools have to be inspected by a specialist in regular intervals.
- When using the machine, no cooling water is allowed to get into the motor and the electric mounting parts, no matter in which position you work.
- If water leaks from the space between gearbox housing and water supply, stop working and have the tool repaired in an authorised service workshop.
- The diamond wet drill END 40 A is not suitable for overhead drilling
- Keep the handles dry, clean and free of oil and grease.
- Do not touch rotating parts.
- Persons under 16 years of age are not allowed to use the tool.
- Always work concentrated. Always work in a carefully considered way and do not use the tool when you are not concentrated.
- Always hold the machine with both hands and maintain a safe standing position. Always consider the reaction moment of the tool.
- Remove the battery pack from the machine before making any adjustments, changing tools, maintaining or cleaning.
- Avoid inadvertent starts by making sure that the machine is switched off before fitting the battery pack.
Safety instructions for battery pack:
- Protect battery packs from water and moisture!
- Do not expose battery packs to fire!
- Do not use faulty or deformed battery packs!
- Do not open battery packs!
- Do not touch contacts or short-circuit battery packs!
- A slightly acidic, flammable fluid may leak from defective Li-ion battery packs! If battery fluid leaks out and comes into contact with your skin, rinse immediately with plenty of water. If battery fluid leaks out and comes into contact with your eyes, wash them with clean water and seek medical attention immediately!
Transport of li-ion battery packs:
- The shipping of li-ion battery pack is subject to laws related to the carriage of hazardous goods (UN 3480 and UN 3481). Inform yourself of the currently valid specifications when shipping li-ion battery packs. If necessary, consult your freight forwarder.
- Only send the battery pack if the housing is intact and no fluid is leaking. Remove the battery pack from the machine for sending. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).
For further safety instructions please refer to the enclosures!
Commissioning
Battery pack
Charge the battery pack (1) before use. If performance diminishes, recharge
the battery pack.
The ideal storage temperature is between 10°C and 30°C.
Li-Ion battery packs “Li-Power” have a capacity and signal indicator (2):
- Press the button (3), the LEDs indicate the charge level.
- If one LED is flashing, the battery pack is almost flat and must be recharged.
Removing the battery pack
Press the battery pack release button (4) and pull the battery pack (1)
forwards.
Inserting the battery pack
Slide the battery pack (1) in until it engages.
Switching on and off
Short-Time Operation
- Switching-on : press on/off switch (5)
- Switching-off: release on/off switch (5)
Permanent Operation
- Switching-on: press the on/off switch (5) and, keeping it pressed, engage the lock-on button (6)
- Switching-off: press the on/off switch (5) and release it again
The machine is equipped with an electronic switch.
With this switch the speed can be regulated according how much pressure you
apply. The use is only recommended for start drilling easily.
A permanent operation with reduced speed will lead to an overload, as less
cooling air will then be available for the motor which consequently overheats
much faster.
Water Supply
The END 40 A is equipped with a water pressure tank (7) to supply the drill
bit with cooling water.
To fill the water pressure tank, the pump unit (8) must be unscrewed. Fill the
tank with approx. 0.5 l clear water up to the “max.water” mark and screw the
pump unit back in. Make sure that the ball valve (9) is closed during this
process.
When filling the water pressure tank, make sure that no water enters the air
slits of the machine, use a funnel if necessary.
Pump several times to increase the water pressure in the tank accordingly.
Make sure that water does not leak uncontrolled anywhere!
Drilling
Switch on the machine and open the ball valve (9). The flow rate can also be
regulated via this.
The contact pressure while drilling (especially with drill diameters from
20mm) should be measured in a way that the machine is not overloaded. An
excessive contact pressure does not lead to faster drilling. The desired
drilling depth can be set with the depth stop (10). Open the wing screw (11)
and pull out the depth stop until the distance between the tip of the drill
bit and the tip of the depth stop corresponds to the desired drilling depth.
Only use the END 40 A for wet drilling. Dry drilling causes damages on the
shaft sealing rings and early wear of the drill bit.
Drill Bit Changing
Attention!
The machine might heat up enormously when you use or sharpen it. You could
burn your hands or get cut or ripped by the segments. Always use protective
gloves when changing the drill bit.
The drill spindle of the END 40 A has a right-hand thread.
To hold on spindle always use a jaw wrench SW 13.
Never remove the drill bit with impacts because this way the machine will be
damaged. With some waterproof grease, which is put on the drill bit thread,
you can remove the drill bit easier.
Care and Maintenance
Repairs have to be carried out only by qualified and due to education and
experience suited personnel. After every repair the machine has to be
inspected by an electric specialist. Due to its design, the machine needs a
minimum of care and maintenance.
The following works have to be carried out regularly:
- The electric tool as well as the ventilation slots always has to be clean.
- During work, please pay attention that no foreign elements get into the interior of the machine.
- In case of failure, a repair has to be carried out by an authorized service workshop.
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. EIBENSTOCK’s application service team will gladly answer questions concerning our products and their accessories.
Environmental Protection
Raw material recycling instead of waste disposal
In order to avoid damages on transportation, the tool has to be delivered in
solid packaging. Packaging as well as unit and accessories are made of
recyclable materials and can be disposed accordingly.
The tool’s plastics components are marked according to their material, which
makes it possible to remove environmental friendly and differentiated because
of available collection facilities.
Only for EU countries
Do not dispose of electric tools together with household waste material!
In observance of European Directive 2012/19/EU on waste electrical and
electronic equipment and its implementation in accordance with national law,
electric tools that have reached the end of their life must be collected
separately and returned to an environmentally compatible recycling facility.
Special notes regarding cordless machines:
Battery packs may not be disposed of with regular waste. Return faulty or used
battery packs to your
Eibenstock dealer!
Before disposal, discharge the battery pack in the power tool. Prevent the
contacts from short-circuiting (e. g. by protecting them with adhesive tape).
Noise / Emission
Measured sound values determined according to EN 62841-2-1. Typically the
A-weighted noise levels of the product are: Sound pressure level LwA 75 dB(A)
Sound power level LpA 86 dB(A)
Uncertainty K 3 dB
Wear ear protectors!
Vibration total values ah and uncertainty K determined according to EN 62841-2-1:
- Vibration emission value ah 2,7 m/s2
- Uncertainty K 0,3 m/s2
The declared vibration emission level represents the main applications of the
tool. However, if the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over
the total working period.
Identify additional safety measures to protect the operator from the effects
of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
Warranty
According to the general supply conditions for business dealings, suppliers
have to provide to companies a warranty period of 12 months for redhibitory
defects. (To be documented by invoice or delivery note.)
Damage due to natural wear, overstressing or improper handling are excluded
from this warranty. Damages due to material defects or production faults shall
be eliminated free of charge by either repair or replacement. Complaints will
be accepted only if the tool was returned in non-dismantled condition to the
manufacturer or an authorized Eibenstock service centre.
EU Declaration of Conformity
We declare under our sole responsibility that the product described under
“Technical Data” is in conformity with the following standards or
standardization documents:
EN 62841-1, EN 62841-2-1
according to the provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EG
Technical file (2006/42/EC) at:
Elektrowerkzeuge GmbH Eibenstock
Auersbergstraße 10
D – 08309 Eibenstock
Lothar Lässig General Manager
05.07.2022
Frank Markert Head of Engineering
Declaration of Conformity
We declare under our sole responsibility that the product described under
“Technical Data” is in conformity with the following standards or
standardization documents:
BS EN 62841-1, BS EN 62841-2-1
according to the provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EG
Technical file (2006/42/EC) at:
Elektrowerkzeuge GmbH Eibenstock
Auersbergstraße 10
D – 08309 Eibenstock
Lothar Lässig
G e n eral Manager
05.07.2022
Subject to change without notice.
Frank Markert Head of Engineering
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>