ibiza LZR300RGB-GOBO RGB Laser with 12 Gobos 300mW User Manual
- June 6, 2024
- ibiza
Table of Contents
ibiza LZR300RGB-GOBO RGB Laser with 12 Gobos 300mW
- RGB LASER WITH 12 GOBOS 300mW
- LASER RGB AVEC 12 GOBOS 300mW
- RGB LASER MIT 12 GOBOS 300mW
- RGB LASER MET 12 GOBO‘S 300mW
- RGB LASER Z 12 GOBOSI 300mW
- RGB LASER S 12 GOBO EFEKTAMI 300mW
Ref.: LZR300RGB-GOBO (15-1253)
LASER FOR PROFESSIONAL USE ONLY
This laser complies with the international standards EN60825-1:2014. It is
meant exclusively for professional use.
Its installation and use should only be carried out by a skilled technician
who is aware of the specific dangers of lasers.
REMINDER OF SAFETY INSTRUCTIONS
- Lasers of class 3 and 4 are for outdoor use only.
- Inside the public area, any laser shooting towards the audience is strictly forbidden except if a safety area of 5 m radius is marked around the area to which the audience cannot get access.
- The area called “public area” is defined by the space of 3m above the area occupied by the audience and a width of 2.5m around this area. The public area must be clearly identified by signs on the ground.
- Inside the public area only a scanning movement is allowed within the terms and conditions defined by the international technical laser safety report.
- The laser unit must be installed out of reach of the audience and at a minimum of 3m above the ground where the audience is present or protected by a safety perimeter of 5m radius.
- The laser unit must be installed in such a way that it can’t be moved under the effect of disruptions such as crowd movements, vibrations or gusts of wind.
Safety Instructions
Please read these instructions carefully, they include important information about the installation, usage and maintenance of this product.
- Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also receives this instruction booklet.
- Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture.
- This product is intended for indoor use only!
- To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit while operating.
- The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
- Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse size and type.
- Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use its carrying handles.
- Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the fixture at temperatures higher than this.
- In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
- Don’t connect the device to a dimmer pack.
- Make sure the power cord is never crimped or damaged.
- Never disconnect the power cord by pulling or tugging on the cord.
- Avoid direct eye exposure to the light source while it is on.
DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
Specifications
- Power supply……. 100-240Vac via 12Vdc 1A mains adaptor
- Red diode ……….. 100mW – 650nm
- Green diode ……… 50mW – 532nm
- Blue diode ………. 150mW – 450nm
- Heat-up time ………….. 2-8 minutes
- Dimensions………106 x 104 x 55mm
- Weight………….0.42kg
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture.
Product Overview
- MODE button
- LED indicator
- Microphone
- Wireless remote sensor
- R&G/R&B/G&B Laser output
- Green laser dimmer
- 12V Power in
- Cooling fan
Operating Instructions
Manual Mode
Access to the 3 different operating modes via the MODE button on the front
panel.
Mode description
-
Autorun and Sound-active auto-switching operation
The LED indicator on the front of the unit will be orange (or flashing orange) when the Autorun and Sound-active auto-switching mode is selected. -
Sound-Active Mode
The LED indicator on the front will be green when sound-active mode is selected. -
Autorun
The LED indicator on the front will be red when autorun mode is selected. -
Power off
The LED indicator on the front will be off.
Wireless Remote Control
The wireless remote control will immediately override the MODE button. No additional settings are required.
- Select Autorun mode or Autorun + Sound-active auto-switching mode
- Sound-active mode
- Power ON/OFF
- Select laser color in forward order
- Select laser color in reverse order
- Turn the RGB LASER on/off
- Turn the RGB LASER on/off
- Reduce the sensitivity of the microphone
- Increase the sensitivity of the microphone
- 1: Autorun slow rotation
2: Autorun stepping, fast rotation
3. Autorun rotation back and forth
4: Autorun and sound-active auto switching same as 1 5: Autorun and sound- active auto switching same as 2 6: Autorun and sound-active auto switching same as 3
IMPORTANT NOTE: Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed.
©Copyright Lotronic 2017
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>