sOmfy RCSSV1 Situo 1 Variation RTS Motorised Blind Accessory Instructions

sOmfy RCSSV1 Situo 1 Variation RTS Motorised Blind Accessory

Safety and liability

Liability

These instructions must be kept by the user. Failure to follow these instructions or use of the product outside its field of application is forbidden, and will invalidate the warranty and discharge Somfy of all liability.
This Somfy product must be installed by a professional motorisation and home automation installer. Moreover, the installer must comply with the standards and legislation currently in force in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product.Never begin installing without first checking the compatibility of this product with the associated equipment and accessories. If in doubt when installing this product and/or to obtain additional information, contact a Somfy adviser or go to the website www.somfy.com.

Safety instructions

• Do not use or install this product outdoors.
• Keep the product out of reach of children
• Do not knock or drop the product, exppose it to flammable materials or sources of heat or moisture, or spplash or immerse it.

The RTS Situo 1 Variation and theRTS Situo 5 Variation in detail

1.  Wall mounting recess
2.  Up/On/Open button
3.  STOP/my button
4.  Variator
5.  Down/Off/Close button
6.  Key activation indicator light
7.  Key activation and group selection indicator lights
8.  Group selector
9.  PROG button
10.  Wall mounting.

Selecting the groups on the RTSSituo 5 Variation

Press repeatedly on the group selector h to select the correct group. The indicator light g for each group from 1 to 4 is lit individually then all the indicator lights are lit if group 5 is selected.

 Installation

 Adding/deleting an RTS Situo Variation

To add or delete the RTS Situo Variation to or from an application: (Figure C)

1. On the individual control already associated with the application

Press the PROG button (≈ 2 s) until the application moves up and down.

1. On the RTS Situo Variation to be added or deleted

Briefly press the PROG button: the application moves up and down and the RTS Situo Variation is added or deleted.

  Fastening

1. Remove the protective film from the adhesive on the back of the wall mounting.
2.  Fasten the wall mounting to a flat, clean and dry surface. Press for optimum bonding.
3.  Place the RTS Situo Variation on the mounting.

 Use

 Group selector on the RTS Situo 5 Variation

This allows the group to be displayed and changed (5 groups are available):

• Short press: visualization of the group selected.
• Press several times: change of group.gap
• Group 5: all 4 indicator lights come on

Buttons

• – : Up / On / Open
• : Down / Off / Close

Variator

• vary the angle of the adjustable slats on Venetian blinds
• vary the lighting and heating.

 STOP button

• Briefly press to stop the application from being activated.
• If the application has been stopped, briefly press to activate it until the favourite position

Setting, modifying or deleting the favourite position

• Place the application in the required position then press (≈ 5 s) to set the favourite position (my).
• Place the application in the favourite position (my) and press (≈ 5 s) to delete it.

 Tips and recommendations

To replace the last RTS control point lost or broken, contact a motorization and home automation professional.

Replacing the battery (Figure I)

Following the figure, remove the rear panel from the remote control, replace the battery with a new one with the same characteristics then close the panel.

Technical data

• Frequency range and maximum power used: 433.050 MHz – 434.790 MHz e.r.p. <10 mW
• Radio range: 20 m between two walls.
• Operating temperature: 0°C to +50°C
• Power supply: 1 type CR2430 battery, 3 V.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>