SOLARIS Mozart Party Light User Manual
- June 6, 2024
- SOLARIS
Table of Contents
USER MANUAL
Introduction
PRODUCT OVERVIEW
The Solaris Mozart is an extremely versatile, creative pixel-mapping and
decorative lighting tool that can be placed almost anywhere. Blazing fast
(38,400Hz), with Cree ™
LEDs, Mozarts are ideal for high-speed photography and video. Modes include 1,
4, or 16 pixels (3 to 48 DMX channels) per fixture.
The ProPlex Mozart Drive PortableMount (10-way max.) in a rugged ProPlex
enclosure is designed for portable use or truss-mounting with yoke included.
Coming soon is the ProPlex Mozart Drive Rackmount 2U (40-way max.) which
supports DMX, RDM, ArtNet, and sACN protocols. It features a large front-panel
touchscreen and a dedicated PC configuration utility.
- Great for low-weight load-bearing structures and surfaces.
- Approx. 11,000 NITS! Brighter than nearly all outdoor LED walls!
- Rain and dust resistant IP65 enclosure – use in all environments!
- Ultra-high refresh rate – 38,400Hz! Great for high-speed photography and videography.
- Single cable, simple power-data connections, daisy-chain, or split–location flexibility.
- Extremely compact and lightweight – 4.7 x 4.7 inches. Only 1 ¼ lb.
- Easy remote addressing and mode switching via RDM
UNPACKING INSTRUCTIONS
Upon receipt of the fixture, carefully unpack the carton and check the contents to ensure that all parts are present and in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear to be damaged from shipping or if the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
POWER REQUIREMENTS
Before powering the unit, make sure the line voltage is within the range of accepted voltages. This fixture accommodates 100-240VAC, 50/60Hz. All fixtures must be powered directly from a switched circuit and cannot be operated with a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0-100% switch. When powered up, Solaris performs a preprogrammed internal test. On initial power-up, the factory default DMX address appears on the display screen and Solaris is ready for operation. After the initial power-up, the last saved DMX address will appear.
SAFETY INSTRUCTIONS
Please read these instructions carefully. This user guide contains important information about the installation, usage, and maintenance of this product.
- Please keep this User Guide for future reference. If the unit is sold to another user, make sure they also receive this instruction booklet.
- Ensure fixture is connected to the proper voltage, and that line voltage is not higher than that stated on the fixture.
- Make sure there are no flammable materials close to the unit while operating.
- Always disconnect from the power source before servicing or fuse replacement. Always use the fuse specified in this manual..
- Always use a safety cable when hanging fixtures overhead.
- The maximum ambient temperature (Ta) is 40°C (104°F). Do not operate fixture at temperatures above this rating.
- In the event of a serious operating problem, stop using the unit immediately. Repairs must be carried out by trained, authorized personnel. Contact the nearest authorized technical assistance center. Only OEM spare parts should be used.
- Do not connect the device to a dimmer pack.
- Make sure the power cord is never crimped or damaged.
- Never disconnect the power cord by pulling or tugging on the cord.
- Avoid direct eye exposure to the light source during operation.
Caution! There are no user-serviceable parts inside the unit. Do not open
the housing or attempt any repairs yourself. In the unlikely event your unit
may require service, please contact your distributor.
Disconnect the power cord before replacing a fuse and always replace with
the same type fuse.
FUSE REPLACEMENT
The Mozart Drive PortableMount uses a 4A, 250V, slow-blow, 5x20mm (0.2×0.8
in.) fuse. Mozart fixtures have no fuse. To replace fuse:
- With a screwdriver turn the fuse cap counter-clockwise to remove fuse cap with fuse.
- Replace fuse attached to fuse cap.
- Reinsert fuse cap with new fuse and tighten clockwise.
MOUNTING/RIGGING – MOZART DRIVE PORTABLEMOU NT
Orientation
The Mozart Drive PortableMount may be mounted on truss or pipe, in any
position, using the yoke supplied with the unit. Always make sure there is
adequate room for ventilation.
Rigging – Always consult a certified rigging engineer before suspending any
fixture overhead!
Use ProBurger ® couplers or equivalent C- or O-type clamps for attaching to
truss. After establishing the desired position, retighten both knobs.
- Always use safety cables!
- When selecting an installation location, consider routine maintenance.
- Never mount Mini enclosure where it will be exposed to moisture, high humidity, extreme temperatures, or restricted ventilation.
2. Setup A DMX data link is needed to run light shows of one or more fixtures
using a DMX-512 lighting console. The combined number of channels required by
all of the fixtures on the DMX data link will determine the number of fixtures
the DMX data link can support.
Important: Fixtures on a DMX data link must be daisy-chained in one single
line. To comply with the EIA485 standard, no more than 32 devices should be
connected on one data link. Connecting more than 32 fixtures on one serial
data link without the use of a DMX optically-isolated splitter may result in
deterioration of the digital DMX signal. Maximum recommended DMX data link
distance between fixtures: 300 meters (984 ft.)
DMX CONNECTOR CONFIGURATION FOR MOZART DRIVE
Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohmmeter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.
SETTING UP A DMX SERIAL LINK
- Connect the (male) 5-pin connector side of the DMX cable to the output (female) 5-pin connector of the DMX console.
- Connect the opposite end of the cable (female) to the input connector of the Mozart Drive consisting of a (male) 5-pin connector.
- Proceed to connect from the Mozart Drive output as stated above to the input of the following Drive, etc.
- Continue linking until the last fixture is conected in your DMX chain.
Operating instructions
PIXEL MAP
Mozart consists out of 64 RGB 1 chip engines which are located in 8 rows and 8
columns.
There are 3 control modes for Solaris Mozart fixtures:
- As 1 pixel unit (3 channel mode)
- As 4 pixel unit (12 channel mode)
- As 16 pixel unit (48 channel mode)
You can only change these modes using the RDM protocol and an RDM enabled controller.
INTERNAL ADDRESS SET
The Mozart Drive must be addressed via RDM.
To set the address for Mozart fixtures, first set the starting address for the
Mozart 10-way power supply .
To set the fixture address of Mozart fixtures (1-10), follow these steps:
Press and hold
The current internal addressing number will appear (1-10).
To change this number, press
RDM
Using RDM you also have an option to locate the device. This will force
selected Mozart to strobe its sequence umber in white.
SENSORS
Mozart has 3 sensors:
- Temperature sensor
- Bus current sensor
- Main voltage sensor
Bus current and main voltage values can be seen only using RDM compliant
lighting control devices (for example, ProPlex ® MasterFade).
To see the current temperature of Mozart, press the “Address set” button
located at the back of the fixture.
If Mozart’s temperature is below or equal 40°C (104°F), one green pixel (4
LEDs) will appear as shown:
Mozart’s temperature is indicated by the number of illuminated pixels: i.e.,
one pixel equals 2.5°C increase. In addition, as Mozart’s temperature
increases, more red pixels are illuminated. At 60°C (140°F) the fixture is
prompted to slowly decrease the LEDs’ output intensity to reduce the
temperature of the fixture.
For example, the diagram below shows the current temperature of a Mozart that
is 60°C (40°C base pixel and 8 additional pixels):
Appendix
RDM FUNCTIONALITY
Mozart Drives have RDM Functionality. Below are the RDM functions available in
these devices. TMB has many options for RDM control of your devices: ProPlex
RDMigo nd IQ RDM Manager Software; ProPlex Striker; and ProPlex MasterFade.
Additionally, ProPlex RDM Opto-Splitters and the ProPlex IQ product range
offer many means of RDM over DMX data distribution.
| Main | Display | Voltage (V) | Current (A) |
|---|---|---|---|
| Mode | Display invert | Present value | Present value |
| DMX address | Display level | Highest value | Highest value |
| RDM version | Lowest value | Lowest value | |
| Software version |
GENERAL MAINTENANCE
To maintain optimum performance and minimize wear fixtures should be cleaned
frequently. Usage and environment are contributing factors in determining
frequency. As a general rule, fixtures should be cleaned at least twice a
month. Dust build-up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear.
Be sure to disconnect power to the fixture before conducting maintenance.
Unplug the fixture from power. Use a vacuum or air compressor and a soft brush
to remove dust collected on external vents and internal components. Clean all
glass when the fixture is cold with a mild solution of glass cleaner or
Isopropyl Alcohol and a soft lint-free cotton cloth or lens tissue. Apply the
solution to the cloth or tissue and drag dirt and grime to the outside of the
lens. Gently polish optical surfaces until they are free of haze and lint.
The cleaning of internal and external optical lenses and/or mirrors must be
carried out periodically to optimize light output. Cleaning frequency depends
on the environment in which the fixture operates: damp, smoky or particularly
dirty surroundings can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. Always dry
the parts carefully. Clean the external optics at least every 20 days. Clean
the internal optics at least every 30 to 60 days.
LIMITED WARRANTY
Solaris LED fixtures (the Product) are warranted by TMB against defective
materials or workmanship for a period of two (2) years from the date of
original sale by TMB.
TMB’s warranty shall be restricted to the repair or replacement of any part
that proves to be defective and for which a claim is submitted to TMB before
the expiration of the applicable warranty periods.
This Limited Warranty is void if the defects of the Product are the result of:
- Opening the casing, repair, or adjustment by anyone other than TMB or persons specifically authorized by TMB
- Accident, physical abuse, mishandling, or misapplication of the product.
- Damage due to lightning, earthquake, flood, terrorism, war, or act of God.
TMB will not assume responsibility for any labor expended, or materials used,
to replace and/or repair the Product without TMB’s prior written
authorization. Any repair of the Product in the field, and any associated
labor charges, must be authorized in advance by TMB. Freight costs on warranty
repairs are split 50/50: Customer pays to ship defective product to TMB; TMB
pays to ship repaired product, ground freight, back to Customer.
This warranty DOES NOT cover consequential damages or costs of any kind.
A Return Merchandise Authorization (RMA) Number must be obtained from TMB
prior to return of any defective merchandise for warranty or non-warranty
repair. For all repairs please contact TMB Tech Support Repair using the
contact information below or email
TechSupportRepairNA@tmb.com.
527 Park Ave., San Fernando, CA 91340
Tel: +1 818.899.8818
Fax: +1 818.899.8813
tmb-info@tmb.com
www.tmb.com
RETURN PROCEDURE
Returned merchandise must be sent prepaid and in the original packing, call
tags will not be issued. The package must be clearly labeled with a Return
Merchandise Authorization Number (RMA #). Products returned without an RMA #
will be refused. Please contact TMB and request RMA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief
description of the cause for the return. Be sure to properly pack fixtures,
any shipping damage resulting from inadequate packaging is the customer’s
responsibility. TMB reserves the right to use its own discretion to repair or
replace the product(s). As a suggestion, proper UPS packing or double-boxing
is always a safe method to use.
Note : If you are given an RMA #, please include the following
information on a piece of paper inside the box:
- Your name
- Your address
- Your phone number
- The RMA #
- A brief description of the symptoms
MOZART RGB FIXTURE – TECHNICAL SPECIFICATION
DIMENSIONS / WEIGHT
Length ………………………………………………………………………………………………………………………………………………… 4.7 in / 119 mm
Width ……………………………………………………………………………………………………………………………………………………. 1.8 in / 45 mm
Height …………………………………………………………………………………………………………………………………………………. 4.7 in / 119
mm
Weight ………………………………………………………………………………………………………………………………………………… 1.25 lb / 565 g
POWER
Operating voltage ………………………………………………………………………………………………………………………………………….. 48V
DC
Power consumption ……………………………………………………………………………………………………………………….. 20W @ full
load
DMX/ power connectors……………………………………………………………………………………………………… Amphenol Sensor
M12
LIGHT SOURCE
LEDs ………………………………………………………………………………………………………………………………………….. 64 Cree LMC-E LEDs
Colors…………………………………………………………………………………………………………………………………………………………………….. RGB
Beam spread ……………………………………………………………………………………………………………………………………………………….. 120°
Refresh rate …………………………………………………………………………………………………………………………………………….. 38,400Hz
Average Color Wavelength ……………………………………………………………………………………………………………… red: 625
nm green: 530 nm blue: 460 nm
THERMA L
Max ambient temperature ……………………………………………………………………………………………………………………………… +40°C
Min. ambient temperature ……………………………………………………………………………………………………………………………….
-20°C
Cooling ……………………………………………………………………………………………………………………………………………………. Convection
IP rating ……………………………………………………………………………………………………………………………………………………………….. IP 54
CONTROL & PROGRAMMING
Control ……………………………………………………………………………………………………………………………………… DMX-512A with RDM
Color dimming control …………………………………………………………………………………………………………………………. 16bit or
8 bit
Pixel modes ………………………………………………………………………………………………………………………………………………………. 1, 4,
16
DMX Channels ……………………………………………………………………………………… 3, 12, 48 (based on selected
pixel mode)
PROPLEX MOZART DRIVE PORTABLEMOUNT – TECHNICAL SPECIFICATION
DIMENSIONS / WEIGHT
Depth ………………………………………………………………………………………………………………………………………….. 10.72 in /
272.3 mm
Width (with yoke) …………………………………………………………………………………………………………………………. 7.95 in /
202 mm
Height (with yoke) ……………………………………………………………………………………………………………………… 5.33 in /
135.4 mm
Weight ……………………………………………………………………………………………………………………………………………. 9.85 lb / 4.46
kg
POWER
AC power IN ……………………………………………………………………………………………………………………………………………….. 100-240V
AC power IN connector …………………………………………………………………………………………………………………….. user-
specified
Power consumption ……………………………………………………………………………………………….. 200W max. (with 10
Mozarts)
DMX/ power OUT connector ……………………………………………………………………………………………… Amphenol Sensor
M12
DC power OUT …………………………………………………………………………………………………………………………………………………….. 24V
THERMAL
Operating temperature ………………………………………………………………………………………….. -4° to +104°F /
-20° to +40°C
Cooling ……………………………………………………………………………………………………………………………………………………. Convection
IP rating ……………………………………………………………………………………………………… IP20
CONTROL & PROGRAMMING
Control ………………………………………………………………………………………………………………………………………… DMX-512 with RDM
DMX Channels ………………………………………………………………………………………………………………………………………………. 3, 12, 48
DMX input ……………………………………………………………………………………………………………… locking 5-pin XLR male
socket
DMX output for further linking ………………………………………………………………………… locking 5-pin XLR
female socket
DMX output for Mozart …………………………………………………………………………………………………………………………………. 10
max.
Solaris Mozart user manual version 2.5 04162021
TMB 24/7 Technical Support US/Canada: +1 818.794.1286
Toll Free: 1 877.862.3833 (877.TMB.DUDE)
UK: +44 (0)20.8574.9739
Toll Free: 0800.652.5418
e-mail: techsupport@tmb.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>