beamZ S1500 DMX MKII Smoke Machine Instruction Manual

beamZ S1500 DMX MKII Smoke Machine

Warning

• The smoke machine must be placed at least 100 cm away from inflammable materials such as curtains, books, etc. Make sure that the housing cannot be touched by accident.
• For indoor use only.
• During installation, nobody should stand beneath the mounting area.
• Prior to the first use, have the unit checked by a qualified person.
• The unit contains voltage-carrying parts. DO NOT open the smoke machine
• Never plug or unplug the unit with wet hands.
• If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.
• If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a main outlet. It needs to be repaired by a qualified technician.
• Only connect this unit to an earthed mains outlet of 230Vac/50Hz.
• Always unplug the unit during a thunderstorm or when it is not in use.
• If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please let the unit reach room temperature prior to use.
• When you unplug the unit from the mains always pull the plug, never the lead.
• In order to prevent the dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a steel cable, etc. which has to be fastened separately from the mounting bracket.
• The supplied bracket is the main fixing and must be used to solidly mount the light effect.
• In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings must be fulfilled.
• Keep out of the reach of children.

Safety

Plug the smoke machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord can only be replaced by an original replacement, supplied by Tronios. Be careful when filling the fluid tank. First of all, unplug the mains lead! Then unscrew the cap on the tank and fill it by means of a funnel. Only use the original Beamz smoke fluid which is environmental friendly and, if used correctly, leaves no residues. Do not obstruct the openings on top of the case to guarantee a good ventilation. The heating element of the smoke machine generates heat which needs to be removed. Don’t put any objects on the smoke machine.

Installation and Use

Unpack the fog machine. Do not connect yet the net cable. Connect the remote control to the connector on the back of the fogger. Fill the fluid tank by means of a funnel. Plug the unit into a mains outlet. Thus the heating element is automatically switched on. Depending on the room temperature, it takes about 8 minutes until the working temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up.
Push the switch once and the smoke machine will produce a nice thick fog. Once the smoke machine has reached its working temperature (the LED is lit) the smoke machine can produce continuously fog during max 1 minute.
After this period of time, the fog generator is cooled so much down that the thermostat switches off. Wait a few minutes until the working temperature is reached again. It is recommended to produce smoke with small pauses in between so that the temperature is maintained and the thermostat doesn’t switch off.

Location

Select a location where it is easy to fill the tank. It is also possible to hang the unit by means of the supplied holder and fixing screws.

Switching the unit off

Switch the unit off by unplugging it from the mains. Otherwise, the 1500W heating element will draw unnecessarily current.

Timer remote control Connect the remote control to the connector on the back of the fogger.
Connect the remote control to the connector on the back of the fogger. After some warm-up time, the device is ready for use, the LED will light up on the remote. During use, it may happen that the machine stops, in this case the LED will go out, indicating that the machine is warming up.

• Timer function: Press the yellow button and set the interval, duration and volume control to the desired level.
• Interval: time between the smoke moments (10-200 seconds)
• Volume: amount of smoke (0-100%)
• Duration: duration of the smoking time
• Continuous function: Press the red button and set the volume to the desired level. The machine will continuously produce an amount of smoke. It may be that the machine in between have to warm up, during this period no smoke is produced. How many times this is done depends on the amount of smoke.
• Manual Mode: Press the green button to produce 100% smoke immediately; this button overrides all previous settings.

DMX control

Connect the device directly to a DMX controller or a DMX loop with multiple DMX effects. The machine has a 3-pin XLR connector for DMX connection.
The machine needs 1 DMX channel to function:

Address Setup: Use the DIP switch on the rear panel to set the start address. The base/start address is defined as a first channel, where responsive to the device. Check if no overlapping channels are used!

Switch dip 10 on to activate the addressing Set the desired address with the remaining 9 dips

Example addressing:

Startadres /Dipswitch setting

• 1 0000000001
• 5 0010000001
• 33 0000010001
• 6 1010000001
• 25 0001100001
• 67 0100001001
• 8 1110000001
• 105 0001011001

Note: It is necessary always lock a DMX loop with a 120 Ohm terminator for correct data transmission.

Maintenance

Refilling the fluid reservoir should be done carefully. Remove the plug from the mains first! Then unscrew the cap of the reservoir and fill it by means of a suitable funnel. Use only the original Beamz smoke liquid. This fluid is environmentally friendly, biodegradable, and leaves no residue when used correctly. Make sure the smoke liquid becomes contaminated, close the cap of the liquid smoke can and after filling tank right. After 40 hours, the smoke machine must be cleaned to avoid deposits in the machine, pump, and heater.

Clean procedure: Run clean procedure in a well-ventilated area

•  Remove smoke liquid from the tank, add cleaning solution to tank
• Switch smoke machine and wait until it is warm up
• Press the button to switch the liquid pumped through the machine
• Perform the above operation until the tank is empty
• Fill the tank with liquid smoke

Specifications

• Power supply: 220-240V~/50Hz
• Heating element:  1500 watts
• Heat up time: 8 minutes
• Continuous use:  Max. 1 minute
• Smoke production: ca. 295 m3/minute
• Tank capacity:  ca 2 liters
• Dims: 465 x 310 x 210mm
• Weight 5.6 kg

Accessories

Smoke fluid, high-quality fluid on a water basis, specially designed for Beamz smoke machines. Guarantees trouble-free use.

• 5-liter packaging, ref. no. 160.583
• 1-liter packaging, ref. no. 160.644

Flavor, adds a pleasant fragrance to the air. One bottle is sufficient for a 5-liter smoke fluid.

• coconut 160.650
• mint 160.651
• vanilla 160.652
• tropical 160.653
• strawberry 160.654

Electric products must not be put into household waste. Please bring them to a recycling center. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.  Do not attempt to make any repairs yourself. This would invalidate your warranty. Do not make any changes to the unit. This would also invalidate your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Tronios BV cannot be held- re4 s-p possible for personal injuries caused by the disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

References

• NVMP - Home
• Samen zijn we open. Samen staan we sterk. - Stichting Open
• Sound & Light distributor - Tronios.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>