Linocell 23826-27 True Wireless Earbuds User Manual

June 6, 2024
Linocell

Linocell 23826-27 True Wireless Earbuds

Linocell 23826-27 True Wireless
Earbuds

Overview

Linocell 23826-27 True Wireless Earbuds fig
1

Specifications

  • Bluetooth: 5.0
  • Range: 10 m
  • Battery time: 4 + 12 hrs
  • Charging time, earbuds: 1.5 h
  • Charge time, case: 1.5 h
  • Charging: USB-C
  • Battery: Li-Po 3.7 V, 30 mAh/3.7 V, 300 mAh
  • Frequency: 20 Hz – 20 kHz
  • Wireless frequency: 2.4-2.48G
  • Transmission power: 20 mW (max)

Included

  • 2x Earbuds
  • 1x Charging case
  • 1x USB-C cable
  • 1x User manual

Use

Charge the case and earbuds fully before first use.

Power on/off

Take the earbuds out of the case to start the headset. If the LED-indicators are off when taking the earbuds out, charge the case and try again.
Place the earbuds back in the case to turn them off or press and hold the touch control surface for 5 seconds. They can also be powered on by holding the touch control surface for 2 seconds when they are not in the case.
To save battery time, the earbuds automatically turn off after 5 minutes of being out of range from their Bluetooth device.

Pairing

Open the case and remove the earbuds. They start to flash and pair together. Open the Bluetooth settings on your device and connect to “BTH-30”.
Pairing occurs automatically after this each time the earbuds are removed from the case.

Charging

Connect the USB-C cable to the charging port on the case and a computer or a USB power adapter to charge the case. There are four LED indicators inside the case that lights up to indicate the battery level. They will gradually fill up.
Put the earbuds in the case to charge them. Each earbud has an LED indicator that turns red while charging. When the earbuds are fully charged the indicator turns off.

Touch control for music and voice assistant

  • Play/pause: Tap the left or right earbud once.
  • Next song: Triple-tap the right earbud.
  • Volume + : Double-tap the right earbud.
  • Previous song: Triple-tap the left earbud.
  • Volume – : Double-tap the left earbud.
  • Voice assistant: Hold the touch control surface of the left or right earbud for 3 seconds to turn voice assistant on.
  • Gaming mode: Tap the left or right earbud 5 times to enter the gaming mode with low latency.

Touch control for calls

  • Answer a call: Tap the left or right earbud once.
  • Hang up a call: Tap the left or right earbud once.
  • Reject a call: Hold the touch control surface of the left or right earbud for 3 seconds.

Reset

If the earbuds do not pair correctly, try to reset.
Take the earbuds out of the charging case. Turn them off by holding the touch control surface of both earbuds for 5 seconds. When they are turned off, press and hold both earbuds for 10 seconds until the LED indicators turn red and flash 3 times. Put the earbuds back in the case and take them out again. The earbuds automatically pair together, but you must reconnect them to your phone (repeat the steps under the heading “Pairing”).

Troubleshooting

FAQ

Q1: Pairing fails.

  1. Put the earbuds back in the charging case and make sure that they are turned off.
  2. Take the earbuds out of the charging case. They enter pairing mode automatically. Choose “BTH-30” in your phone’s Bluetooth settings to pair.
  3. If the pairing still fails, check the following points:
  4. Make sure the earbuds and your Bluetooth device are next to each other or within 10 metres and that there are no obstacles between them.
  5. Make sure there are no signal interferences nearby (check the question “Connection is not stable” for signal interference conditions).
  6. Try to reboot your Bluetooth device.

Q2: I paired the earbuds with my phone before, but I failed to pair them again.
Turn on Bluetooth in your phone and in “My devices”/”Paired devices”, choose “BTH-30″, tap ” ” and “Forget This Device”. Then, pair the earbuds with your phone again.

Q3: Connection is not stable.
Make sure that the Bluetooth connection distance is not more than 10 metres and that there are no objects between the earbuds and your Bluetooth device, or a radio or wifi signal that is interfering.

Q4: Power runs out fast.
The earbuds’ playtime varies depending on the volume level and audio content.
Put the earbuds back into the charging case after use to avoid unnecessary power consumption.

Q5: The earbuds are reconnecting to my phone while being charged in the case.
When the charging case is out of power during charging, the earbuds automatically turn on and reconnect to the latest paired Bluetooth device. If the earbuds are not paired with a Bluetooth device, they automatically turn off after 5 minutes.

Safety information

This product contains a rechargeable Li-Po battery and the battery cannot be replaced.
To prevent possible hearing damage, do not listen at high volume levels for long periods of time.

Simplified EU Declaration of Conformity

Kjell & Company hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of the EU declaration of conformity is available at www.kjell.com/23826

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals