TESLA 32T313BH 32 Inch HD LED TV User Manual
- June 6, 2024
- Tesla
Table of Contents
TESLA 32T313BH 32 Inch HD LED TV
OVERVIEW
OPERATING INSTRUCTION
Please read these instructions before operating your set and retain them for
future reference.
INSTRUCTION
Accessories
1x safety instructions/warranty cards, 1x remote control, 2x AAA batteries
Equipment set-up
Fig.1: NOTE: The graphics are for representation only.
Install the display on a solid horizontal surface such as a table or desk. For
ventilation, leave a space of at least 10 cm free all around the set. To
prevent any fault and unsafe situations, please do not place any objects on
top of the set. This apparatus can be used in tropical and/or moderate
climates.
The symbols serve as follows:
WARNING:
Indicates warning information.
NOTE:
indicates any other additional important or helpful information.
MENU:
Represents a button on the remote control or the TV. (Bold characters
Move to:
Represents a menu item within a window. (Italic characters)
Default PIN code: 0000
Front panel/underside
Fig.2l: NOTE: The graphics are for representation only.
- Power indicator /remote sensor
- Speakers
- Combo button
Rear panel
Fig.3: NOTE: The graphics are for representation only.
-
AC INPUT (FIXED CABLE) Main power cable (180 – 240 V ~ 50/60 Hz)
-
Vesa 100 x 100 4 x screws holes to mount TV to the wall
Fig.3a:
NOTE: The graphics are for representation only.
button
- Turn on the TV.
- The TV is on, press it to display the Button menu.
- In the Button menu, short press it to select the menu, long press it to confirm the selection.
Side panel
Fig.3b:
NOTE: The graphics are for representation only.
- COMMON INTERFACE (CI) Connect a Conditional Access Module (CAM).
- USB Connect a USB device for playback of multimedia files
- EARPHONE Speakers will be muted when the earphone is plugged in and the headphone is selected.
- AV IN 3.5 mm female jack entry for composite video and left/right audio connection
- HDMI 1 Connect HDMI input signal from a signal source such as DVD, Blu-ray player, or game console
- HDMI 2 (ARC) Connect HDMI input signal from a signal source such as DVD, Blu-ray player, or game console.
- SATELLITE IN Connect a satellite dish to the TV for searching programs.
- ANTENNA IN Connect a terrestrial antenna or cable connection from your provider to the TV for searching programs.
- S/PDIF Use an RCA cable to connect your TV to a compatible digital amplifier or Home theatre set
Remote control
Fig.4: NOTE: The graphics are for representation only.
- SOURCE Select the input source mode.
- q Press to turn the TV on or standby.
- 0 ~ 9 Choose channel directly.
- ECO Screen brightness modes for energy saving
- GUIDE Toggles the Electronic Programme Guide between on and off. Only available fo digital channels.
- MENU Open the menu options.
- EXIT Exit the current menu.
- Z OOM -/+ Press to select the desired screen format. (In USB mode, it is unavailable.)
- Navigate The menu.
- OK Confirm your selection. Under the TV source, press the OK key to open the Channel list.
- OPTION Displays the function menu to perform certain operations. Press to enter the Picture mode directly.
- RETURN Returns you to the previous channel in TV mode.
- VOL +/- Adjust the volume up or down.
- INFO Display the status information.
- MUTE Press to mute or restore the volume.
- CH +/- Change programs up or down.
- TEXT Teletext.
- SUBTITLE Press to display the Subtitle Language menu.
- LIST Press to enter into the channel list.
- TV Goes to the TV mode.
- Red, Green, Yellow button In the corresponding mode, press it to enter the right function as a hint.
- Blue button m In the corresponding mode, press it to enter the right function as a hint.
- In USB mode, press to select soundtrack mode.
- In DTV mode, press to select Audio Languages.
- In ATV mode, press to select Sound Type
Installing the batteries
Fig.5: NOTE: Pictures are only for reference. Actual items may differ.
Precautions for using the battery
Improper use of the battery will cause leakage. Carefully follow these
instructions.
- Please note the batteries’ polarity to avoid short circuits.
- When the battery’s voltage is insufficient which an act the use range, you should replace it with a new battery. Remove the batteries from the remote control unit if you do not intend to use it for a long time.
- Do not use di event types of batteries (for example Manganese and Alkaline batteries) together.
- Do not put the battery into fire, and charge or decompose the battery.
- Please dispose of batteries to abide by relevant environmental protection regulations.
Using the remote control
- Use the remote control by pointing it towards the remote sensor. Items between the remote control and the remote sensor could block normal operation.
- Do not cause the remote control to vibrate violently. Also, do not splash liquid on the remote control, also do not put the remote control in a high humidity place.
- Do not place the remote control under direct sunlight which will cause deformation of the unit by heat.
- When the remote sensor is under direct sunlight or strong lighting, the remote control will not work. If so, please change the lighting or TV’s position, or operate the remote control closer to the remote sensor.
FIRST TIME INSTALLATION
After all connections have been made properly, switch on your TV. Insert the
main power plug into the wall outlet, now the red LED light should light up.
Press the q button on your remote control to wake the TV up. The language and
country selection will appear on the screen. Use to select the OSD Language of
your preference. Use to select the Country and use again to select the region
you are using this TV. This country/region selection is an important setting,
it will set the time zone and will try to sort region channels at first or in
a specific order.
If all settings are made, confirm with OK on your remote control and follow
the next steps.
On the next screen, you can select which tuner you like to use and which
channels you’d like to search for. Choose Tuner Type and by pressing you can
choose between DTV, ATV, or DTV + ATV (DTV to search digital broadcasts; ATV
to search analog broadcasts). After you made your selection, press to proceed
to Digital type. In this menu you can select which input source you would like
to use:
- Satellite to receive satellite broadcasts (if you are equipped with a satellite dish)
- DVB-T to receive terrestrial broadcasts (by using an indoor or outdoor antenna)
- DVB-C to receive cable broadcasts. (Connection to cable outlet box)
Then the next screen appears depending on the tuner selection you choose.
DVB-S/S2 installation
Satellite Setting
Press to select the satellite your dish is aimed at. Use the buttons to change
settings for your satellite installation for each specific satellite.
Channel Search
Press to highlight the options of choice and press OK to start the channel
search.
- Scan Mode Choose between Default (recommended), Blind Scan, and Network
- Channel Type Select Free to search Free-To-Air channels only. Select Scramble to search Encrypted channels only. All Channels to search FTA and Encrypted channels
- Service Type Select DTV to search DTV channels only, RADIO to search radio channels only, or All for a complete search.
It is recommended to use the default settings.
DVB-T/T2 installation
Terrestrial Setting
Here you only need to press OK to start searching.
All settings are automatically set by the country selection you made in the
first step.
NOTE: If you have an active antenna, please check the user manual of the antenna for the external power supply. The TV can NOT supply power used for an active antenna.
DVB-C installation
Table Setting
Press Arrow to highlight your settings.
Scan type You can select Network Scan or Full. (Default Network Scan for quick search advised)
NOTE : Full scan will have a duration of approximately 20 minutes, depending on your cable network.
- Frequency Please enter (with 0 ~ 9) the main frequency used by your provider in KHz.
- Network ID Please enter (with 0 ~ 9) the used Network ID from your provider.
- Symbol Please enter (with 0 ~ 9) the used Symbol from your provider. (Ks/s)
NOTE: Please check the settings for your cable system used by your provider!
MENU SETTINGS
Menu control (DTV mode)
Press MENU to enter the main menu. Press to select an item. Press and OK to
select the submenus. Press MENU to exit the item.
Picture menu
- Picture Mode Select the automatic picture control mode. Available choices are Dynamic,
- Colour Temp Select the overall color tone of the picture. Available choices are Cold, Normal, and Warm.
- Noise Reduction Eliminates noise in the picture. Available choices are: Off, Low, Middle, High, and Default
In the Personal mode, settings can be changed for Brightness, Contrast, Colour, Tint, and Sharpness.
Sound menu
- Sound Mode Select your favorite sound mode for each input. Choices are Standard, Music, Movie, Sports and Personal.
- Treble Adjusts the higher frequency of the sound.
- Bass Adjusts the lower frequency of the sound.
- Balance Control the sound balance between the right and left loudspeaker (earphone).
- Auto Volume Level Adjust the volume corresponding to the input audio level. Options are On and Off.
- SPDIF Mode When SPDIF output is connected to the digital home audio system you can select Auto to output Dolby audio* automatically. When you choose PCM, stereo audio is selected only and you can switch off this output.
- AD Switch Turn on the Audio description, you can activate the setting of AD volume. When turn on the audio description, a narrator will describe what is happening on the screen for blind or visually impaired viewers. (Only if available in DTV mode.)
Availability depends on the broadcaster
Using PVR
Allows you to record your favorite TV program to a USB device. Before you use
the function, connect a USB memory device to the set first.
Press Menu to display the Main menu, select “ PVR File System” and press the OK button to enter.
- Selects Disk
- Adjusts the recording options
- Press the RED button to start recording.
To watch the recorded program, enter the USB mode> Video. Select the folder
MSTPVR, then select the related record file.
Press OK to play. (It is the same if you record a digital radio program).
GENERAL DATA
Operating voltage: 180 ~ 240 V AC 50/60 Hz
Power consumption: 50 W
Power consumption in standby: <0.5 W
Operating temperature: +5 °C ~ +35 °C
Storage temperature: -15 °C ~ +45 °C
Operating humidity: 20% ~ 80% RH, non-condensing
Storage humidity: 10% ~ 90% RH, non-condensing
LICENSES
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE
WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR
WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE
IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY
BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.
MPEGLA.COM
This product contains one or more programs protected under international and
U.S. copyright laws as unpublished works. They are con dential and proprietary
to Dolby Laboratories. Their reproduction or disclosure, in whole or in part,
or the production of derivative works therefrom without the express permission
of Dolby Laboratories is prohibited. Copyright 2003-2009 by Dolby
Laboratories. All rights reserved.
THIS PRODUCT IS SOLD WITH A LIMITED LICENSE AND IS AUTHORIZED TO BE USED ONLY
IN CONNECTION WITH HEVC CONTENT THAT MEETS EACH OF THE THREE FOLLOWING
QUALIFICATIONS:
- HEVC CONTENT ONLY FOR PERSONAL USE;
- HEVC CONTENT THAT IS NOT OFFERED FOR SALE; AND
- HEVC CONTENT IS CREATED BY THE OWNER OF THE PRODUCT. THIS PRODUCT MAY NOT BE USED IN CONNECTION WITH HEVC ENCODED CONTENT CREATED BY A THIRD
- PARTY, WHICH THE USER HAS ORDERED OR PURCHASED FROM A THIRD PARTY, UNLESS THE USER IS SEPARATELY GRANTED RIGHTS TO USE THE PRODUCT WITH SUCH CONTENT BY A LICENSED SELLER OF THE CONTENT. YOUR USE OF THIS PRODUCT IN CONNECTION WITH HEVC ENCODED CONTENT IS DEEMED ACCEPTANCE OF THE LIMITED AUTHORITY TO USE AS NOTED ABOVE.
Tesla declares that the equipment complies with the European Directive
2014/30/EU (EMC) and the Low Voltage Directive 2014/35/EU (LVD) and the ErP
Directive 2009/125/EC and Radio Equipment Directive 2014/53/EU and the RoHS
Directive 2011/65/EU in accordance with the following technical standards:
ELECTROMAGNETIC COMPATIBILITY
EN 55032:2015 ;EN 5 5020:2007+A12:2016 ;EN 55024:2010+A1:2015 ;EN
61000-3-2:2014 ;EN 61000-3-3:2013
LOW VOLTAGE
EN60065:2014
ENERGY RELATED PRODUCTS
Commission regulation (EC) No 642/2009; EN50564:2011; IEC62087:2011
RED
EN 303 340 V1.1 .2:20 16-09 ;EN 303 372-2 V1.1.1:2016-04
RoHS
EN50581:2012
Subject to alterations. In consequence of continuous research and development,
technical spec cations, design, and appearance of products may change.
Manufactured under license from Dolby Laboratories. Dolby Audio and the
double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and
the High-De nit ion Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries. All
product names are trademarks or registered trademarks of their respective
owners.
© Tesla 2020. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>