ULTIMEA Apollo P20 Full HD Projector User Guide
- June 9, 2024
- ULTIMEA
Table of Contents
ULTIMEA Apollo P20 Full HD Projector
Prefer video tutorial?
Setup guidance video and User Manuals on UL TIMEA website.
IMPORTANT: Before using the projector, please read these set up guide, for more detailed instruction, please go to check the online User Manual. Your product may differ from the illustrations on this sheet, but the instructions are the same.
Note: Due to Type-C protocols, android phone/pad can not be played by USB or HD cable connection.
ACCESSORIES LIST
PRODUCT
REMOTE CONTROL
QUICK SETUP
Power On / Power Off
Plug in the AC power cord, click the power button on the operation panel of
the machine or on the remote control and the projector will start to work.
Projector Installation
You can choose horizontal placement or hanger installation.
The projection screen can be played from 35″ to 120″. The recommended projection screen is 40″ to 80″. Ambient darkness will improve the clarity of the projected images.
The distance between Apollo P20 and the projection surface must be a miniumun of 1.1 meters (43 inches) and maximum of 3.88 meters (153 inches).
Adjusting the projector image
Please adjust the dial slowly to bring the picture into focus
Adjust the Image Projected On the Screen
Check the horizontal and vertical settings of the projector till the image on
the screen is balanced.
KEYSTONE CORRECTION
- Adjust the keystone on the projector to adjust the images shape.
- Adjust the placement of the projector. When the left side of the picture is wider, move the left side of the projector corresponding to the picture forward; when the right side of the picture is wider, move the right side of the projector corresponding to the picture forward.
INPUT SOURCE
Wired Connection to Devices
Fire TV Stick Connection
How to connect the Fire TV stick to the projector:
- Connect the TV stick to power using the USB cable.
- Plug the TV stick to one the HD port on the projector.
- Select the HD option in the settings on the projector.
The content of the Fire TV stick will be displayed on the projection screen. Use the Fire stick’s remote to select and stream your content.
HD mode
- Step 1 : Connect the projector and device with HD cable.
- Step 2 : Press and hold the Source button a of the projector or remote control to enter the input source interface.
- Step 3 : Select HD1 or HD2 that you had connected, press OK to enter, press return key to exit and return to the main interface of the projector.
USB mode
- Step 1 : Connect the projector to the USB.
- Step 2 : Press and hold the Source button -a of the projector or remote control to enter the input source interface.
- Step 3 : Select USB and press OK to enter the module interface (the same of home page).
- Step 4 : Select the corresponding Movie, Music, Picture and text modules of the file type, and press OK to enter the file interface
- Step 5 : Select the file to be played in the file interface and press OK to select play.
- Step 6 : Press the return key to exit and return to the main interface of the projector.
AVmode
- Step 1 : Connect the projector and the device with the AV cable.
- Step 2 : Press and hold the Source button -a of the projector or remote control to enter the input source interface.
- Step 3 : Select AV, press OK to enter, press return key to exit and return to the main interface of the projector.
BT SETTINGS
- Power on and enter the projector’s main menu, select BT and click OK button to confirm.
- Turn on BT and select the BT signal that needs to be connected.
Enjoy your new projector!
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
ISED WARNINGS
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with lnnovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subiect to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
NOTE : This euipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and use in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity
We(Manufacturer is responsible for this declaration) Dynanic (Shenzhen) Technology Limited (Company name) 20th Floor, Building 4, Tianan Cloud Park, Bantian St., Longgang District, Shenzhen,China (Company address) Declare under our sole responsibility that the product
- Trade name : ULTIMEA
- Equipment : Projector
- Model No.: U0321
To which this declaration relates is in conformity with the essential requirement set out in the Council Directive on the Approxmation of the laws of the Member States relating to LVD Directive(2014/53/EU)&Rohs (2011/65/EU)
- EN 62368-1:2014+A11:2017
- EN IEC 62311:2020
- ETSI EN 301 489-1 V2.2.3(2019-11)
- ETSI EN 301 489-17 V3.2.4(2020-09)
- EN 55032:2015
- EN 55035:2017
- EN 61000-3-2:2019
- EN 61000-3-3:2013+A1:2019
- ETSI EN 300 328 V2.2.2(2019-7)
- IEC 62321-3-1:2013
- IEC 62321-5:2013
- IEC 62321-4:2013+AMD1:2017
- IEC 62321-6:2015
- IEC 62321-7-2:2017
- IEC 62321-6:2015
- IEC 62321-8:2017
Made in China
Manufacturer : Dynanic (Shenzhen) Technology Limited Address: 20th Floor,
Building 4, Tianan Cloud Park, Bantian St., Longgang District, Shenzhen, China
518000
FCC ID : 2A9OO-U0321P
IC : 29805-U0321P
@Dynanic Inc. All rights reserved, registered in the United States and other countries. 16192 Coastal Hwy Lewes DE 19958, United States If we can be of assistance, please do not hesitate to contact us.
- +1 888-598-8875 (US)
- Mon-Fri 9am-5pm (PST)
- +49 89-628-25828 (EU)
- Mon-Fri 9am-5pm (CET)
- support@ultimea.com
- support.ultimea.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>