FUWEI SC061-WCR2 Smart Battery Doorbell User Manual
- June 10, 2024
- FUWEI
Table of Contents
SMART BATTERY
DOORBELL
USER MANUAL
SC061-WCR2 Smart Battery Doorbell
Thank you for purchasing Smart Battery Doorbell. Get started using your new devices by downloading TuyaSmart, one convenient app that manages everything straight from your phone. Easily connect to your home Wi-Fi and control multiple devices from the touch of your fingertips.
What’s in the Box
- Smart Battery Doorbell ×1
- User Manual ×1
- Back Veneer x 1
- Loud speaker x 1
- USB Cable ×1
- Adapter ×1
- Screw bag ×1
- Reset Pin×1
- Screw Wrench×1
*: Different products have different accessories, please refer to physical packing.
Screws Bag
Security Screws-1pcs: Use one to mount your Smart Doorbell on the Bracket. Mounting Screws-2pcs: Use two to mount the Bracket on the wall. Wall Anchors-2pcs: (Optional) Push two anchors in the holes you drilled in the wall when installing on concrete, stucco, or brick, you should.
Get Ready
- Know your Wi-Fi network and password
- Make sure your mobile device is running iOS® 8 or higher or Android™ 4.1× or higher
- Make sure you’re connecting to a 2.4GHz Wi-Fi network (It can’t connect to 5GHz networks)
-
Download the TuyaSmart app from App Store or Google Play.
-
Register an account on your TuyaSmart app
STEP 1. Enter your mobile phone number or email address.
STEP 2. Enter the verification code and create a password. -
Plug in
How do I reset my device?
Press the Reset Button (as Pic) for several seconds until camera starts to beep.
Using the screw to remove the down panel.
Optional: Insert SD card as shown in Pic.
How to pair the doorbell with the loud speaker ？
- Please power up the loud speaker.
- Press the Reset Button for several seconds until device starts to ding dong, at the time, the lamp flashing slowly and the device enters the pairing state.
- Press the doorbell button to pair, the loud speaker starts to dingdong and pilot lamp off, the device paired successfully.
System Requirements
- Mobile device running iOS 8 or higher or Android 4.1x or higher® TM
- Existing Wi-Fi Network
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
Please read the instruction manual carefully before using the product
4 Add device
-
Open TuyaSmart APP, click “+” on the top right corner of the page “HOME”, then select “Smart Camera”.
-
Make sure the indicator light on the device is white slowly flashing, then press “Next Step”.
-
Enter your “Wi-Fi network and password”, click “OK”.
-
Read the instruction about “Scan with the camera”, click “Continue”.
-
Scan the QR Code on your phone with camera. Heard a prompt tone, click “Heard the beep”.
-
When the indicator light on the device turns from flashing red light to steady green light, the network configuration is complete.
*Please refer to the specific APP interface if there are any
difference.
Frequently Asked Questions
Can I share with family and friends?****
– Yes, you can share your cameras with family and friends who will have access to view the camera and control your bulbs, plugs, and other devices. In the app, press the Profile button and click on the “Home Management” button, and you will be able to give or revoke sharing permissions. In order to share, the other user should already have downloaded the app and registered a new account.
What’s the Wireless Range?****
– The range of your home Wi-Fi is heavily dependent on your home router and
the conditions of the room.
– Check with your router specifications for exact range data.
The device appears offline or unreachable?****
– Make sure your Wi-Fi router is online and in range.
– Make sure you have the latest app functionality by clicking “Check for
firmware update” in your device settings.
Cannot connect to your Wi-Fi network.****
– Make sure you entered the correct Wi-Fi password during the Wi-Fi setup.
– Check whether there are any Internet connection problems. If the Wi-Fi
signal is too weak, reset your Wi-Fi router and try again.
How many cameras can I control?****
– TuyaSmart app can control an unlimited amount of devices in an unlimited amount of locations. Your router may have a limit of how many devices can be connected to one router.
Is the process same when I add the device through wifi or network cable?****
Yes, they have same process, you can use forth step to add device.
Description of assembly steps
- Hammer expansion bolt into wall body as per the hole position of locating sticke;
- Use a screw to fix the back plate;
- Put the doorbell downward to buckle it on the back plate to complete installation.
Mount your smart doorbell on the bracket with security screws