LINOVISION 4GPTZ Portable Mobile Emergency Suitcase User Manual
- June 6, 2024
- LINOVISION
Table of Contents
PORTABLE MOBILE EMERGENCY SUITCASE
User Manual
Thanks to purchase the products, if you have any questions or requirements,
please feel free to contact us.
As the reference of usage instruction, the description of some details maybe
not so accurate in this manual. The contents of this document will be updated
irregularly for product version upgrading or other reasons, and the update
will be added in the new version of the manual, we will not notify separately.
Please read the manual carefully before installation and use.
Precautions
Please be sure to obey the following when using this product:
- Please read the manual carefully before using the device, and obey the instructions strictly when operating.
- Be sure to turn off all the related power when installing the device accessories.
- Don’t use the device in excessive humidity or high-temperature environment, avoid using the device near the strong interference source and the shielding.
- Avoid dropping the device on the ground or being attacked seriously by another object.
- The product is a precision electronic device, please do not privately disassemble or install without permission.
- Suggest protecting with factory packaging when shipping products.
- The device batteries, power adapter and accessories are specific models, be sure to contact the manufacturer or local dealers the batteries need to be changed, in case of danger caused by improper change or removal.
- Please contact our technical personnel if you have any questions or requirements during the use process.
- Product introduction 4G HD portable emergency command device is a full-featured integrative product with functions of high-definition, smooth, and stable video effect, real-time location, emergency, PTZ operation, two-way talkback, etc. It is a complete set of emergency command devices that are specially designed for unexpected emergencies, and provides technical support for realizing “smooth communication, real-time scene, complete data, and command in place”. The product is widely applied in the occasions of emergency command, public security, criminal investigation, traffic police/patrolman, fire fighting, civil air defense, border defense, urban management, electric power, road administration, etc.
- Appearance and interface description
The product is a 4G multi-functional portable suitcase terminal, the device appearance and corresponding interfaces are as shown below:
Appearance
Upper panel
Lower panel
The functions of the relevant interfaces on the device are shown in the table below：
No.
| Interfaces|
Functions
---|---|---
Upper panel
| HDMI| Synchronously output the screen image
Standard USB| Connect with USB, keyboard, mouse, and other peripherals
Square USB| Develop and debug the installation system, which also can be
connected with peripherals
3.5mm headphone jack| Android system sound output
Lower panel| YC9 aviation plug| Connect with talkback handheld microphone
HDMI| HDMI video input port
Standard USB| Extended LinuxUSB peripherals（power supply is available）
RJ45 network port| System debugging or cable video transmission
Power| Press and hold for 3s to boot, the light is bright; Press and hold for
3s to shut, the light is twinkling.
Network| Short press to switch network connection methods(using cable method
when light is bright while using 4/3G method when light is off)
Video recording| Short press to start/stop video recording (recording when
light is bright while stopping recording when light is off)
Alarm| Press and hold for 3s, the light is bright, device issued a warning to
the platform
PTZ| Four-dimensional rocker, control the camera to turn to the up, down,
left, and right. Rotation, control the camera to zoom out or zoom in.
short press the middle button to capture the image.
TF card slot| Clamshell card slot, push to the left to open the cover, dual
cards up to 128G
SIM card slot| Clamshell card slot, push to the left to open the cover, 4
cards can be extended
Electronic disk| mSATA electronic disk installation position
Indicator panel| | 4/3G dial-up status indication, “1” indicates module number
Figure 1: dial-up success
Figure 2: idle status
Figure 3: card is not detected
| Using the cable connection way can use the cable to connect the BGAN router
to access the command center
| WiFi status indiction (figure 1: not enabled. Figure 2: connection success)
| TF card status indication
| Location indication (bright: locating success. Twinkling: searching
location…)
| Battery indication
| 
| Storage status indication
---|---|---
Side interfaces| | Indicators on the right side Green twinkling: recording Red
bright: stop recording
Red twinkling: low battery warning
| Charging interface on the right side
| HD PTZ camera video input interface on the right side
| GPS antenna interface on the right side
3. Parameter specification
I tems
| Details|
Specifications
---|---|---
Video| Input| 1-channel analog high definition, compatible with CVBS,
AHD1.0,AHD2.0, automatic recognition
1-channel HDMI, up to 1080P@30fps
Interface| Aviation interface on the right side
Compression standard| H.265 和H.264。
Resolution|
CVBS：960H、D1、4CIF、CIF。AHD1.0：720P、VGA。AHD2.0：1080P，720P，VGA。HDMI：1080P，720P，
VGA。
Frame rate| 1~25f adjustable
Bitstream| Support dual-stream, 64kbps~6Mbps can be set
Video adjustment| Brightness, contrast, saturation, adjustable
Snapshot| Support the snapshot of different input source and resolution,
format
Audio| Compression standard| G711A,G711U, ADPCM
Input| 1-channel, built-in microphone or handheld microphone input
Output| 1-channel, built-in loudspeaker or handheld microphone output
Display| Screen size| 13.3 inch
Resolution| 19201080。
Visual angle| 88/88/88/88。
Network| 3G/4G| WCDMA,EVDO,TD-SCDMA,TDD-LTE,FDD-LTE。
WiFi| 802.11b/g/n，2.4G。
Wired| RJ45,10/100M self-adaption Ethernet port
Storage| Medium| TF, up to 128G, dual cards
mSATA| Built-in a mSATA installation position
Format| AVI, 15~60 minutes can be set, start or stop controlled by a button
Location| System| Support GPS and Beidou dual-module locating
Antenna| SMA interface, external
Power| Input| 12.6V@4A DC constant voltage input
Interface| DC5.52.1interface on the right side
Battery| Built-in 3 lithium batteries, 30Ah
Others| Protection| IP67
---|---|---
Dimension| 410340205mm
Weight| 9.2KG
Working humidity| Temperature -20℃~60℃, humidity 5%~95%
4. Configuration and usage
It is necessary to set up some parameters before installing the device, such
as the access platform address, etc. The specific configuration process is as
shown below, please contact the customer service personnel if you have any
questions.
4.1 login built-in webpage
Please login to the built-in webpage according to the following operations,
please contact the customer service personnel if you have any questions.
Connect the device with HD PM camera, SIM card, TF card, mid antenna, start
the device, access to the LAN or PC with cable.
Search the device with the tool “Device configuration assistant”, change the
device IP address to the same network segment with the PC.
Open the browser and input the device IP: 9988, such as 192.1613.0.8:9988.
open the built-in webpage login window. input the user name (adinin) and
password (123456) to log in. Please download and install the plug-in and
restart the browser if it is the first time.
After login, it is available to preview the videos in “real-time surveillance
window”, query and download videos of the TF card in “query download”, change
the device parameters. configure the platform address and networking ways in
“device management”, etc.
4.2 Platform address setting
After login the built-in webpage, enter the “device configuration” page. Click
“system/platform access”, and select “enable platform access”, input the
platform address in the op-up window, such as 60.173.195.210:9988, click
submit and refresh. When the access status shows “access success”, the video
can be previewed after logged in the platform via the network video
surveillance system.
4.3 Access ways
Different network connection way can be selected to make the device access the
platform according to the requirements. Three ways are supported by the device
to connect the network: cable/ WiFi /4G. Fast switching can be realized via
the ‘network” button on the lower panel, and according to the display status
on the indicator panel to judge the connection way and connection status. The
configuration modification also can be realized via client/built-in webpage,
the details are as below:
4.3.1 Cable access
Click after login the built-in webpage, find the “network configuration” in
the system, input the IP address, subnet mask and gateway in the IP settings.
Select “enable DHCP” if use the auto access way, submit.
Select “use the cable” in the “preferred network”, submit.
4.3.2 WiFi access
Click after login the built-in webpage, find the “network configuration” in
the system, and select “use WiFi” in the “preferred network”, submit. Click
WiFi option and select “enable WiFi’, input the wireless network account and
password, submit and refresh. Observe the module status until the connection
is successful. (Note: the hotspot function needs to be shut firstly)
4.3.3 4G/3G access
Click after login the built-in webpage, find the “network configuration” in
the system, and select “use 4G/3G” in the “preferred network”, submit.
Click 4G/3G option, check the dial-up status in the status parameters, the
device has access to the network when it shows “dial-up success”.
It needs to add APN, access number, and password in the configuration
parameters if the used SIM card is the private network card.
5. Scheduling screen operation instructions
As shown in the figure below, the LCD of the upper panel is the android system
touch screen. Main function modules: login status, video command, map command,
query layback, application settings, system settings. The follows will
introduce the function of each module.
Screen function sketch
5.1 Login status
Device connection/login server status are shown on the left upper corn of the
screen.If it displays “Device connection is successful”, it indicates that the
connection between the upper panel and the lower panel is smooth. When it
shows “login server is successful”, it means the device has successfully
logged onto the emergency command system.
As shown in the figure below, if login server is not successful, please check
the network connection, and configure the platform address and user name of
the emergency command system in the “application settings”.
5.2 Application settings
It needs to input the platform address, user name and password in the
“application settings” before login the server. Please login again after save.
The network port IP of the device can be set in the network settings, as shown
in the figure below:
5.3 Video command
Enter the page “video command”, real-time scene image can be seen. 2-channel
HD videos are displayed, one main channel video input source is HDMI, and the
other channel video input source comes from the camera in the right side of
the suitcase. Full-screen display and snapshot are supported.
The online group members are displayed on the right side, click the microphone
icon to shout to the group, or talk to any member in the group and watch his
real-time video.
5.4 Map command
People can master the location information of their own and other portable
terminals in the “map command” page and view the video of other terminals, as
shown in the figure below:
5.5 Query playback
The video files and images saved in the built-in memory card can be queried
and processed playback in the “query playback” page, as shown in the figure
below:
5.6 System settings
Each functional parameter can be changed in the Android system after entering
the page, the same with other Android system settings, no longer describe
details here.
6. Command and scheduling platform
Login to the emergency command and schedule platform after logging into the server to create a cluster group. Group communication, retrieval image, video conference and other functions can be realized. Please refer to the User Manual of emergency command and schedule client for the details.
7. Real-time preview
“network video surveillance system” can be used after device successfully
accessed platform. After login, the real-time image of the online devices can
be viewed. Select an online device, double click to unfold the camera
resource, double click the camera, video will be displayed on the window.
Right click the image to pop up the shortcut bar, snapshot, video recording,
talkback and other functions can be realized, as shown in the figure below:
8. Query playback
Login “network video surveillance system”, click query playback. : query the
videos saved in the platform, : query the videos saved in the device storage
medium. Select device and date, click to query, double click the video file in
the query results to playback, or right click to download the video, as shown
in the figure below:
9. Restore factory settings
9.1 Use “Device configuration assistant”
Make sure PC and device are in the same LAN, open the tool “Device
configuration assistant” to search the device and select it, click icon, find
“device maintenance” in the pop-up window, click “restore factory settings”
to confirm, as shown in the figure below:
9.2 Use “Network video surveillance system/built-in webpage”
Login the network video surveillance system, click “device management”, double
click the device in the device list, select system/device information/restore
factory settings. Operations of the built-in webpage are the same, as shown in
the figure below:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>