av-link BCV Series 952717UK 100V Indoor Speakers User Manual
- June 6, 2024
- Av:link
Table of Contents
av-link BCV Series 952717UK 100V Indoor Speakers
BC3V | 75mm (3”), 60Wmax | White | 952.710 |
---|---|---|---|
Black | 952.711 | ||
BC4V | 100mm (4”), 70Wmax | White | 952.712 |
Black | 952.713 | ||
BC5V | 130mm (5.25”), 90Wmax | White | 952.714 |
Black | 952.715 | ||
BC6V | 165mm (6.5”), 120Wmax | White | 952.716 |
Black | 952.717 |
Introduction
Thank you for choosing the BC-series indoor speakers. These speakers have been designed to offer high quality sound for low impedance installations. Please read and follow the instructions in this manual to achieve the best results and avoid damage through misuse.
Installation
The BC-series speakers are each supplied with a wall-mounting bracket which
allows 90° lateral adjustment. When fixing to a wall or ceiling, use the
bracket to
mark out the fixing points and use appropriate fixings for the substrate that
the speaker will be attached to, ensuring that the fixing is strong enough to
bear the weight.
Once the bracket is fitted, support the speaker in position and attach top and
bottom using the supplied screw caps and adjust to the required angle. Further
mounting points are available at the rear of the speaker, should it be
preferred to use different mounting methods (e.g. 129.130 – 129.124UK)
Note: Do not over-tighten the screw caps as this can cause the threaded
inserts to fail.
Connection
BCV-series speakers are connected via 2 spring terminals at the rear of the enclosure. For 100V operation, use double insulated cable rated to the total maximum current, calculated as total max tapped power divided by 100V. With the amplifier switched off, strip the speaker wire ends and connect 100V or “+” wire to the red terminal and connect Common or “-” to the black terminal. Each model has a 100V transformer built in with various volume settings or “tappings” available via a rotary switch at the rear (BC6V example shown).
When used with a 100V line amplifier, select the required maximum wattage that the speaker should demand from the amplifier. Ensure that the sum of the wattages of all the speakers attached to the amplifier does not exceed the recommended output of the amplifier.
When used with a standard (non-100V) amplifier, select the “8Ω” setting and refer to the amplifier manufacturer’s manual to ensure that total speaker impedance (Ω) is not less than recommended for the amplifier. It is imperative that the amplifier does not deliver more power than can be handled by the BCV speaker. Refer to the amplifier manual and specifications below to calculate this. Normally, it is recommended that the amplifier is capable of the RMS power rating of the speaker but cannot ever exceed the Max power rating.
Specifications
Model | BC3V | BC4V | BC5V | BC6V |
---|---|---|---|---|
Woofer | 75mmØ (3“) | 100mmØ (4”) | 130mmØ (5.25”) | 165mmØ (6.5”) |
Tweeter | 50mmØ (2“) | 25mmØ (1”) | 25mmØ (1”) | 25mmØ (1”) |
Freq response | 120Hz – 20kHz | 110Hz – 20kHz | 100Hz – 20kHz | 90Hz – 20kHz |
Power max : 8Ω | 60W | 70W | 90W | 120W |
Power rms : 8Ω | 30W | 35W | 45W | 60W |
Tappings | 1.5/3/6W, 8Ω | 2.5/5/10/20W, 8Ω | 5/10/20/30W, 8Ω | 5/10/20/40W, 8Ω |
Dimensions (mm) | 106 x 153 x 106 | 150 x 195 x 150 | 180 x 240 x 180 | 220 x 280 |
x 220
Weight| 900g| 1.63kg| 2.38kg| 3.08kg
SPL @ 1W/1m| 88dB| 88dB| 88dB| 89dB
Caution
The BCV-series speakers are intended for indoor use. Avoid moist or dusty
environments.
Avoid excess heat and exposure to direct sunlight.
Take care not to overload speakers. HF drivers are especially prone to damage through overload. For 100V installation, take proper care to insulate any contacts within reach of users.
DIMENSIONS
GRAPHS
Errors and omissions excepted.
Copyright© 2021.
AVSL Group Ltd. Unit 2-4 Bridgewater Park, Taylor Rd. Manchester. M41 7JQ
AVSL (EUROPE) Ltd, Unit 3D North Point House, North Point Business Park, New
Mallow Road, Cork, Ireland
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>