VAULTEK LifePod 2.0 Full Size Rugged Airtight Water Resistant Safe Instruction Manual

: June 6, 2024
: VAULTEK

LifePod 2.0 Full-Size Rugged Airtight Water Resistant Safe
Instruction Manual

Battery Installation

Quick Start Guide Step 1

LifePod” is powered by a 9v Alkaline battery (not included). Under normal use the battery can last up to one year with the interior LED light turned OFF.

To get started, undo both side compression latches to open your LifePod®.
Locate the battery cover on the front wall and remove by pressing on the outer tab (Fig A)
Carefully pull out the 9v battery snap inside the battery compartment and connect an Alkaline 9V battery to the connector. Be sure to snap the battery in the correct orientation (Fig B). A 9v Alkaline battery is not included.
When the battery is snapped in you will hear a short welcome tone and the keypad will light up.
TIP! If you snap the battery in and the keypad is flashing refer to page
Once you hear the tone and see the keypad light up, slide the battery into its compartment being mindful to place the battery ribbon underneath the battery first (fig C). This will make the battery easier to remove when replacing. Replace the battery cover and you are ready to program.

Basic Operation

Quick Start Guide Step 2

With the battery installed, you can now lock and unlock your LifePod°. Unique to LifePod° is a capacitive keypad. There are no physical buttons, but each key can be pressed by touching the keypad surface.

Locking

IMPORTANT Before locking your LifePod, always be sure the side compression latches are latched closed first. This will ensure the locking mechanism engages properly.

To lock, simply press and hold the lock pad for 2 seconds (Fig D).

Unlocking
IMPORTANT Do not undo the compression latches until the unit has been unlocked with the correct master code first. Undoing the compression latches first may cause binding on the lock mechanism and will not unlock.

First, tap the lock pad to wake the unit up (Fig D). When the keypad lights up, your LifePod is awake and ready to accept the code.
Enter the master code. (The default master code is 1-2-3-4) When the code is correct, the status LED will turn GREEN and the lock will disengage.
Undo both side compression latches, and you can open the unit.

TIP! Your LifePod” can protect your belongings against the elements using the side compression latches alone. For extra security, lock the unit with the lock pad as needed.

Master Code Programming

First-time users should change the default code as soon as possible to prevent unauthorized access when using the lock.

TIP: Code Requirements

Your code can be a minimum of 4 digits, or as long as 8 digits
Two keys can not be pressed simultaneously.
Programming a new code will overwrite your previous code.

The PROGRAM button will not function when locked. Be sure the LifePod latch is in the unlocked position.

First, open the unit and tap the lock pad to wake the unit up (fig E). When the keypad lights up, your LifePod is awake and ready for programming.
Press and hold the PROGRAM button for 3 seconds (Fig F) until ALL keys (1-4) turn solid RED.
Enter your new code.
Press and hold the PROGRAM button a second time for 3 seconds (Fig F) until ALL keys (1-4) turn solid RED.
Enter your new code a second time.
Press and hold the PROGRAM button a third time for 3 seconds (Fig L). The status LED (Fig G) will flash GREEN and LifePod° will beep to confirm the code change is successful.

Tip! Water will affect the keypad; performance. Wipe away excess; water and dry off the keypad when opening for best results and to prevent unwanted water; from entering the storage compartment.

Product Registration

Quick Start Guide Step 4

Vaultek” strongly encourages you to register your LifePod” as soon as you receive it. Registration provides many benefits including technical support and ordering replacement keys should you misplace them. Your Vaultek” LifePod° has a unique product number on the inside of the battery door and a 4-digit ID number engraved on the keys. You will need these numbers to register your new unit.

Locate your product number. It is printed on the first page of this user manual and on the back of the battery door (Fig H).
Find your 4-digit ID number engraved on the keys (Fig I).
Please visit the Vaultek” website at vaulteksafe.com and click Support then click Registration from the available options.
Enter the required information in the form and click submit.

Overview

Get to know your Vaultek° LifePod° 2.0.

VAULTEK LifePod 2 0 Full Size Rugged Airtight Water Resistant Safe -
Overview

01. Capacitive Keypad

Introduction

The Vaultek” LifePod° 2.0 is a pin-access portable lockbox. It can be secured using the side compression latches to protect the interior from environmental factors such as water, with the added option of securely locking the unit with the keypad. Its high-impact polymer and portable design make it ideal to transport and protect valuables and personal items. Powered by an Alkaline 9V battery (not included), LifePod combines security with convenient access.

Secure Access; How to open your Vaultek® LifePod®.
Keypad: The 4 digit capacitive keypad responds quickly for access and has a built-in proximity sensor that lights up the keypad when the lock pad is touched. See page 08 for more information.
Key: Two keys are provided for manual access to the safe in the event the battery dies.
Secure Defense; low your Vaultek “ LifePod® keeps people out-
Anti-Impact Latch: Built to withstand forceful impacts.
High Impact Polymer: Engineered to be extremely strong and impact resistant.
Anti-Pry Design: The interior channels and gasket form a seal around the inner chamber making it difficult for tools and other small objects to penetrate.
Security Sleep Mode: Activates when (6) consecutive incorrect keypad entries are entered
LifePod® will not accept any entries for four minutes. If a key is pressed during this time, all of the keys will flash RED, and the alarm beeps. A backup key can be used to open the unit.

Warnings

To prevent damage to your Life Pod® or injury to yourself or to others, read the following safety precautions before using this unit.

IMPORTANT Before locking your LifePod, always be sure the
side compression latches are latched closed first. This will
ensure the locking mechanism engages properly.
IMPORTANT Do not undo the compression latches until the unit has been unlocked with the correct master code first.
Undoing the compression latches first may cause binding on the lock mechanism and will not unlock.
DO NOT submerge in water more than 1 foot deep. The pressure could leak water into the inner chamber. LifePod® is designed to protect against dust and splashes with brief short immersions and will float when loaded with weight up to 2lb.

To ensure proper weather sealing:
ALWAYS check that the rubber gasket is free of debris before closing the lid
ALWAYS check that the side compression latches are fully engaged and closed
ALWAYS check that the front rubber cover is closed tightly
DO NOT expose to extreme heat or cold.
Battery power may be affected. The acceptable operating range is -14f to 120f.
DO NOT store loaded firearms in this unit.

DISCLAIMERS:
Neither seller nor manufacturer shall be liable for any injury, loss, or damage, direct or consequential, arising out of the use of, or the inability to use, the Vaultek” LifePod.
The user shall determine the suitability of the Vaultek” LifePod° before the intended use and the user assumes all risk and liability whatsoever in connection therewith.

Basic Operation

LifePod® can protect belongings from environmental factors using the side compression latches alone without the need for a battery.
With the battery installed LifePod can lock securely using a built-in locking mechanism for additional security. Unique to LifePod is a capacitive keypad.
There are no physical buttons, but each key can be pressed by touching the keypad surface.

Locking
IMPORTANT Before locking your LifePod, always be sure the side compression latches are latched closed first. This will ensure the locking mechanism engages properly.

To lock, simply press and hold the lock pad for 2 seconds (Fig A).

Unlocking
IMPORTANT Do not undo the compression latches until the unit has been unlocked with the correct master code first. Undoing the compression latches first may cause binding on the lock mechanism and will not unlock.

First, tap the lock pad to wake the unit up (Fig A). When the keypad lights up, your LifePod is awake and ready to accept the code.
Enter the master code. When the code is correct, The status LED will turn GREEN and the lock will disengage.
Undo both side compression latches, and you can open the unit.

Battery Installation

LifePod® is powered by a 9v Alkaline battery (not included). Under normal use the battery can last up to one year with the interior LED light turned OFF.

To get started, undo both side compression latches to open your LifePod.
Locate the battery cover on the front wall and remove it by pressing on the outer tab (Fig B).
Carefully pull out the 9v battery snap inside the battery compartment. and connect an Alkaline 9V battery to the connector. Be sure to snap the battery in the correct orientation (Fig C). A 9v Alkaline battery is not included.
When the battery is snapped in you will hear a short welcome tone and the keypad will light up.
TIP! If you snap the battery in and the keypad is flashing refer to page 14.
Once you hear the tone and see the keypad light up, slide the battery into its compartment being mindful to place the battery ribbon underneath the battery first (Fig D). This will make the battery easier to remove when replacing. Replace the battery cover and you are ready to program your LifePod.

Using the Micro-USB Port

A micro-USB port is built into LifePod® behind the front protective rubber cover (Fig E).

In the event, the battery dies while traveling, and you do not have access to the backup keys, you can power on the unit using the backup micro-USB port.

Simply open the rubber cover and plug in a micro-USB cable (not included) into the port. While the cable is plugged into an external power source, LifePod® will function normally allowing you to enter the code and open the unit.

Backup Key Access

The keyhole is located beneath the front protective rubber cover (Fig E)
Two backup keys are provided. In the event, these are needed to open the LifePod, simply open the protective cover, insert one of the backup keys, and turn the key clockwise 90 degrees (Fig F)

IMPORTANT! Always make sure the front protective cover is closed tightly to ensure the unit is sealed correctly for protection from the elements.

Compression Latches

Life Pod’s side compression latches can protect belongings from environmental factors using the side latches alone without the need for a battery.

To Open simply lift from the bottom of each latch away from the unit (Fig G). The latches will lift and disengage, then swing the latches free of the unit (Fig H). The top lid can now be opened.

VAULTEK LifePod 2 0 Full Size Rugged Airtight Water Resistant Safe -
Compression Latches

To Close rest the top of each latch against the top housing (Fig I). The latches will catch and rest in place on their own. Press the bottom of each latch firmly towards the unit to engage (Fig J).
You will hear and feel the latches snap-in in position.

VAULTEK LifePod 2 0 Full Size Rugged Airtight Water Resistant Safe -
Compression Latches 2

Master Code Programming

First-time users should change the default code as soon as possible to prevent unauthorized access when using the lock.

TIP: Code Requirements

Your code can be a minimum of 4 digits, or as long as 8 digits.
Two keys can not be pressed simultaneously.
Programming a new code will overwrite your previous code.

IMPORTANT! The PROGRAM button will not function when locked. Be sure the LifePod” latch is in the unlocked position.

First, open the unit and tap the lock pad to wake the unit up (fig K). When the keypad lights up, your LifePod° is awake and ready for programming.
Press and hold the PROGRAM button for 3 seconds (Fig L) until ALL keys (1-4) turn solid RED.
Enter your new code.
Press and hold the PROGRAM button a second time for 3 seconds (Fig L) until ALL keys (1-4) turn solid RED.
Enter your new code a second time.
Press and hold the PROGRAM button a third time for 3 seconds (Fig L). The status LED (Fig M) will flash GREEN and LifePod® will beep to confirm the code change is successful.

Tip I Water will affect the keypad performance. Wipe away excess water and dry off the keypad when opening for best results and to prevent unwanted water from entering the storage compartment.

Key Lock

Your LifePod® is equipped with an anti-hacking feature for enhanced security. Using the Key Lock feature, you can disable the manual keyway from opening LifePod®.

TIP! The manual keyway can not lock the unit, only unlock.

OFF (Fig N) Default setting. The exterior manual keyway is engaged and fully functional. The manual key can not lock the unit, only unlock.

ON (Fig O) The exterior manual keyway is disengaged. Meaning LifePod’s manual key lock can not be picked open by any hacking and renders the manual key entry disabled.

WARNING When Key Lock is ON, the backup keys will not be able to open the unit. Use with caution.
WARNING When the key lock is ON, the backup keys will not be able to open the unit. If you forget your master code you will be unable to open LifePod®. Use with caution.

Product Registration

Vaultek® strongly encourages you to register your safe as soon as you receive it. Registration provides many benefits including technical support and ordering replacement keys should you misplace them. Your Vaultek” LifePod has a unique product number on the inside of the battery door and a 4-digit ID number engraved on the keys. You will need these numbers to register your new unit.

Locate your product number. It is printed on the first page of this user manual and on the back of the battery door (Fig P).
Find your 4-digit ID number engraved on the keys (Fig Q).
Please visit the Vaultek” website at vaulteksafe.com and click Support then click Registration from the available options.
Enter the required information in the form and click submit.

Hot Keys to Control Sound and Light

Toggle Interior LED Light ON/OFF: The Interior LED light will come on when the lid is open and stays on for about 20 seconds by default. You have the option to disable the light or extend the light to stay on longer.

To toggle the interior LED light options you need to wake up LifePod° by tapping the center Lock Pad (Fig S) then press and hold keys ‘1’and ‘4’ together. The status LED (fig R) will indicate the selected light setting per below:

VAULTEK LifePod 2 0 Full Size Rugged Airtight Water Resistant Safe - Hot
Keys to Control Sound and Light

TIP! If toggled ON the LED may significantly reduce the battery life.

Status LED Solid RED: Interior Light is Off
Status LED Solid GREEN: Interior Light stays on for 20 seconds.
Status LED Flashing Green: Interior Light stays on for 60 seconds.

Toggle Sound ON/OFF: By default, the sound is ON. To toggle the sound ON/OFF you need to wake up LifePod° by tapping the center Lock Pad (Fig S) then press and hold keys ‘2’ and ‘3’ together. The status LED (Fig R) wilt flash RED indicating OFF or GREEN indicating ON.

LED Indicators

LifePod’s capacitive keypad has multiple LEDs built in to provide various feedback. The LEDs will illuminate as needed when the unit is awake. To wake the unit, tap the lock pad.

Status LED (Fig R) The status LED will provide feedback on various commands. It will light GREEN when correct codes are entered and RED when an incorrect code is entered.
Tamper Indication (Fig R)If the status LED is solid RED when awake, this means the unit has detected that an incorrect code has been entered. You can clear the tamper indicator by entering the correct master code.
Battery Indicator (Fig T) When the unit is awake, the battery indicator will light either GREEN or RED Green indicates the battery has sufficient power, and Red indicates the battery is in need of replacement.
Low Battery Warning (Fig Tl The battery indicator will flash RED and sound several rapid beeps.
This continues every 5 minutes until the battery dies to indicate the battery is in need of a replacement.
Lock Pad (Fig S) The lock pad illuminates RED only when the unit has been locked using the keypad, and requires the use of the master code to unlock it. When locked, and the unit is awake, the lock icon will be solid RED.
TIP! If the lock icon is solid RED, do not undo the side compression latches to open the unit. This means the internal lock is engaged and should not be opened. Enter the master code to unlock the unit, as indicated by the lock icon light going OFF. It is now safe to undo the side latches and open the unit.

Securing your LifePod®

Included is a steel security cable to secure the LifePod° to a fixed object.

| |
---|---|---
1 First wrap the looped end of the security cable with an object of your choice, such as a seat bracket under your car seat.| 2 Pull the adapter piece through the loop and cinch tight.| 3 Place the adapter piece in its slot in the LifePod® and close the lid.

Removable Interior Tray

Life Pod® 2.0 is equipped with a removable interior tray. This can be used to divide the storage space and organize as needed or can be removed if preferred when deeper storage space is needed.
The tray features a series of slots that can be used to secure and organize smaller items, such as EDC gear. (Fig U)
Velcro straps (2x Velcro straps included} are attachment methods that you can use to secure belongings to the tray.

FAQ / Troubleshooting More online at vaulteksafe.com under Support

Q: What do I do if the keypad is flashing RED after installing the battery?
A: Your battery is likely low. Replace the battery with a new 9v Alkaline battery. We recommend a brand-name battery like Duracell or Energizer.
Q: Installed a new battery and it is not working.
A: Test normal function by removing the battery and plugging in a micro-USB cable to the micro-USB port. If the unit resumes normal function then the installed battery is bad.
Q: How do I unlock the case if the battery is dead but the case is locked?
A: Plug a micro-USB cable into the front micro-USB port to power the unit so you can unlock and replace the battery.
Q: Is my LifePod® fireproof or waterproof?
A: LifePod® is not fireproof, but is waterproof up to 1 foot deep. It is designed to stay afloat in the water with a weight of up to 2lb.
Q: Can I use the compression latches by themselves and not lock the unit?
A: Yes, the compression latches are designed to seal the interior chamber from the elements and are great for recreational use. The lock can be used when a higher level of security is needed.
Q: What do I do when my keypad is unresponsive?
A: Your battery is likely dead. Replace the battery with a new 9v Alkaline battery. We recommend a brand-name battery like Duracell or Energizer.
Q: What happens if I lose the keys?
A: First, make sure you registered your LifePod® in the event you do lose your keys. Contact us via email at support@vaulteksafe.com. Be prepared to provide your order details and product number to us so we can verify ownership.
Q: Can I travel with my LifePod® through US Customs or TSA security at the airport?
A: Yes, LifePod® qualifies as a secured lockbox for traveling. If transporting firearms, be sure to inform your airline agent when checking in due to Federal law. Be aware, that you may be asked to open your LifePod®, and a person having the master code should be present in case such a request is made by a government authority.
Q: What happens if the lid is not opening?
A: If you have been traveling the atmospheric pressure difference could create a vacuum holding the lid down. Release the pressure by opening the keyhole cover.

Customer Support I Warranty

If you have a problem with your Vaultek® UfePod® that is not answered in the FAQ section of this manual. we encourage you to visit www.vaulteksafe.com/support/.
Limited Warranty (Terms and Conditions)
VAULT EX’ IS COMMITTED TO PROVIDING PRODUCTS OF HIGH QUALITY AND VALUE AND MAKES EVERY EFFORT TO ENSURE ITS PRODUCTS ARE FREE OF DEFECTS.
Vaulick’ guarantees your I. ifePodo will be free of defects in eriatenals or worionansh,p for a period of one year from the date of original purchase from an authorized dealer.
The warranty is only valid for the original purchaser and not transferable.
This warranty is only valid for products purchased and operated in the U.S.
This warranty does not cover abuse. misuse. use in any manner for which is not designed. neglected modify (ahem. damage inadvertently caused by the user. accidents and/or tampering If service is needed Vaultek® will at its option. exchange or repair without charge for pans Or Labor.
Upon authorization of warranty service. customers are responsible for securely packaging products Additionally. customers are responsible for the costs of shipping to and from the Vaulter service center.
If the claimed defect cannot be identified or reproduced, customers will be held responsible for the costs incurred.
Please have the following information available before you beetle claim with Vaultek®

Purchaser’s name mailing address, email address. and a phone number
Copy of receipt or online order number (if purchased directly from us or Amazon)
Authorized Dealer Name (if applicable)
Detailed description of the problem

NEITHER SELLER NOR MANUFACTURER SHALL BE LIABLE FOR ANY INJURY. LOSS OR DAMAGE. DIRECT OR CONSEQUENTIAL. ARISING OUT OF THE USE OF, OR THE INABILITY TO USE THE VAULTEK• LIFEPOO*.

FCC This device complies with part 15 of the FCC rules Operation is subject to the following two conditions: (1)this device may not cause harmful interference. and (2)this device must accept any interference received. including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment Such modifications or changes cou4 void the user’s authority to operate the equipment

VAULTEKSAFE.COM