SALUS EP110 Electronic Programmable Timer Instruction Manual

SALUS EP110 Electronic Programmable Timer Instruction Manual

Introduction

A programmable timers EP110, EP210, EP310 are used to switch ON/OFF the heating system, the hot water or any electronical device like pumps or lights as needed. It works by controlling with programmed schedules (24H or 5-2 schedule types) which contain 3 time programs each.

Product Compliance

EU Directives: 2014/30/EU, 2014/35/EU and 2011/65/EU. Please check www.saluslegal.com for the full information.

Safety Information
Use in accordance with the EU and national regulations. For indoor use only. Keep your device completely dry. This product must be installed by a competent person and in accordance with all the EU and national regulations.

Technical data

Buttons functions

LCD display icon description

1. Device operation (animated icon)

2. Number of hours for the BOOST function

3. ON/OFF indicator

4. Work mode

5. AM/PM

6. Holiday mode

7. Clock

8. The day of the week

9. Program number

10. Zone I operation mode

11. Day of the week

12. Program number

13. ON/OFF indicator

14. Zone II operation mode

15. Zone II work status

16. AM/PM

17. Number of hours for the BOOST function for Zone II

18. Number of hours for the BOOST function for Zone I

19. Zone I work status

20. Clock

21. Holiday mode

22. Zone I operation mode

23. Zone II operation mode

24. Zone III operation mode

25. Program number

26. ON/OFF indicator

27. Holiday mode

28. AM/PM

29. Number of hours for the BOOST function for Zone III

30. Zone III work status

31. Zone I work status

32. Number of hours for the BOOST function for Zone II

33. Zone II work status

34. Number of hours for the BOOST function for Zone I

35. Clock

36. Day of the week

Jumpers settings

Wiring diagram

All wire connectors are located on the back of the device. To remove the cover, loose two screws located at the bottom of the device and then remove the back of the housing.

Note: Disconnect power supply before working with the device.

Setting time and date

Operation modes

There are 5 different work modes available. Using MODE button, you can change modes directly according to the following sequence:

Programming EP110 controller

You can create 3 independent time schedules. There are 2 work models to choose from:

• business days + weekend (5-2)
• each day separately (24 hours) Controller works by default in working days + weekend mode (5-2).

To set each day separately (24 hours), change the jumper position according to the diagram on previous page.

Programming EP210/EP310 controller

You can create 3 independent time schedules for each zone. There are 2 work models to choose from:

• business days + weekend (5-2)
• each day separately (24 hours) Controller works by default in working days + weekend mode (5-2).

To set each day separately (24 hours), change the jumper position according to the diagram on previous page.

HOLIDAY mode

Holiday mode is used to disable all controller outputs for a specified number of days (up to 31 days). When HOLIDAYS mode is active, aircraft icon will appear on the display.

Disabling the Holiday mode

BOOST Function

BOOST function extends the active program time to 1-9 hours. Press +Hr button to activate BOOST mode (each press of the button extends the active program by 1 hour).

Factory Settings

DISTRIBUTOR OF SALUS CONTROLS:
QL CONTROLS Sp. z o.o., Sp. k. Rolna 4, 43-262 Kobielice, Poland

Importer:
SALUS Controls Plc Units 8-10 Northfield Business Park Forge Way, Parkgate, Rotherham S60 1SD, United Kingdom

www.salus-controls.eu
SALUS Controls is a member of the Computime Group. Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change specification, design and materials of products listed in this brochure without prior notice.

References

• SALUS Controls - intelligent temperature control

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>