SALUS SD600 Smart Photoelectric Smoke Sensor User Guide

: June 6, 2024
: SALUS

Table of Contents

Introduction
Product Compliance
Safety Information
Product Overview
Proper Placement
Button Operation
LED Indication
Installation
App Pairing
Dashboard display
Battery replacement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SALUS SD600 Smart Photoelectric Smoke Sensor User Guide

Introduction

SD600 is a smart photoelectric smoke sensor, with ultra-low-power ZigBee wireless network technology design. It is capable of real-time detecting the presence of smoke. Once it detects danger of fire smoke, the red LED flashes rapidly and the sound alarm will alert you timely. For an internet connection (Online Mode), SD600 must be used with the Universal Gateway UG600/UGE600 and the SALUS Smart Home App. You can also use SD600 without an internet connection (Offline Mode).

Product Compliance

This product complies with the essential requirements and other relevant provisions of the following EU Directives: RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity is available on www.saluslegal.com

2405-2480MHz; <14dBm

Safety Information

Use in accordance to national and EU regulations. Use the device as intended, keeping it in dry condition. Product for indoor use only. Installation must be carried out by a qualified person in accordance to national and EU regulations.

Warning

Do not install the smoke detector in places with high temperature, high humidity, high noise area or high frequency interference.

This product is a household smart smoke detector and it can trigger the flash and sound alarm when it detects smoke, but it cannot put out a fire.

Product Overview

A: Network Button
B: Test / Mute Button
C: Battery
D: Bracket

Proper Placement

Flat Ceiling

The preferred location to install the smoke detector is in the centre of the ceiling because smoke, heat and combustible products rise to the ceiling and will laterally spread. Keep at least 30 cm distance from lights and decorations and at least 15 cm distance from walls and corners

Sloping Ceiling

Sloping Ceiling

Please install the smoke detector at 90 cm horizontal distance from the ceiling top

Button Operation

To set the device into pairing mode, press and hold the network button for 3 seconds.

To disconnect the device from the network, press and hold the network button for 5 seconds.

To test or to mute the alarm, press and hold the Test / Mute Button for 3 seconds.

LED Indication

State	LED	Alarm Sound
Standby	Red LED flashes every 53 sec	N/A
Test	Red LED flashes quickly	rapid Di-Di-Di”
Alarm	Red LED flashes quickly	rapid “Di-Di-Dim
Mute	Red LED flashes every 10 sec	N/A
Low Power	Red ti.me LED flashed one	‘Di” every 53 sec
Fault	Red LED flashed twice every 53 sec	“Di-Di” twice for every 53 sec
Pairing mode	Green LED flashes 5 times per sec	N/A
Pairing successful	Green LED solid for 3 sec	N/A
Pairing unsuccessful	Green LED flashes slowly (twice per sec) six times	N/A
Disconnect	Red LED turns on, then Green LED flashed slowly six times	N/A

Installation

Rotate the sensor anticlockwise to separate it from the bracket
Install the bracket using the screws or the provided double-sided tape.

Remove the double-sided tape and stick the alarm into the ceiling.

Remove the battery insulating strip to turn on the detector and rotate the sensor clockwise into the bracket.

App Pairing

Go to the App
1. 1. 1. 1. Press and hold the network button for 3 seconds

Dashboard display

No Smoke

Smoke

Battery replacement

Replace the battery following the correct polarity

SALUS CONTROLS DISTRIBUTOR:
QL CONTROLS Sp. z o.o.,
Sp. k.
ul. Rolna 4,
43-262 Kobielice,
Poland

Head Office:
SALUS Controls Plc
Units 8-10 Northfield
Business Park
Forge Way, Parkgate, Rotherham
S60 1SD, United Kingdom
T: +44 (0) 1226 323961
E: sales@salus-tech.com

http://www.salus-controls.eu/

Computime: SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change specification, design and materials of products listed in this brochure without prior notice.