ROROSHETTA CILINDRO WH Wall Mounted Cooker Hood Instruction Manual

Instruction Manual

SAFETY INFORMATION

For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance.

**** The wire connection has to be done by a specialized technician.

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.

• The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).

• If the instructions for installation for the gas hob specify a greater distance, this must be respected.

• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.

• Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

• For Class I appliances, check that the domestic power supply guarantees adequate earthing.

• Connect the extractor to the exhaust flue through a pipe of a minimum diameter of 120 mm. The route of the flue must be as short as possible.

• Regulations concerning the discharge of air have to be fulfilled.

• Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with energy other than electricity, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes from being drawn back into the room by the cooker hood.

• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent.

• Connect the plug to a socket complying with current regulations, located in an accessible place.

• With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities.
  WARNING: Before installing the Hood, remove the protective films. Use only screws and small parts in support of the hood.
  **WARNING:** Failure to install the screws or fix the device in accordance with these instructions may result in electrical hazards.

• Do not look directly at the light through optical devices (binoculars, magnifying glasses…).

• Do not flambè under the range hood; risk of fire.

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Children should be supervised to ensure that they do not play with the appliance.

• The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction.
  **** Accessible parts may become hot when used with cooking appliances.

• Clean and/or replace the Filters after the specified time period (Fire hazard). See paragraph Care and Cleaning.

• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).

• The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about the recycling of this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.

CHARACTERISTICS

Dimensions

Components

INSTALLATION

Wall drilling and bracket fixing

When installing the hood in the recycling version it has to be taken into consideration that the space remaining between the hood and the upper limit (ceiling or self) is at least 8-10 cm.

On the wall, draw:

• a Vertical line up to the ceiling or upper limit, at the center of the area in which the hood is to be fitted;
• a Horizontal line at a minimum of 1150 mm above the Cooker Top; .
• As indicated, mark a reference point at 100 mm to the right of the vertical reference line.
• Repeat this operation on the other side, checking that the two marks are level.
• As indicated, mark a reference point at 390 mm above the horizontal reference line, and at 100 mm to the right of the vertical reference line.
• Repeat this operation on the other side, checking that the two marks are level.
• Drill at the points marked, using a ø 10 mm drill bit.
• Insert the plugs 11 into the holes.

Hood support mounting

• Lean the hood support 3 against the wall making sure that holes in the hood support correspond to those in the wall.
• Block the hood support to the wall using 4 12a (5 x 70) screws supplied with the hood.
• Before fastening the screws definitively make sure that the support is well-leveled. Only after this operation proceeds with the definitive tightening of the screws.

Air outlet connection in the ducting version
When installing the hood in ducting version, based on the installer’s choice, a rigid or a flexible pipe with a ø 150 o 120 mm is used in order to connect the hood to the air outlet piping. The pipe connection can be made on the upper part or on the backside of the hood.

• Insert flaps 11b on the Hood Canopy Outlet.

AIR OUTLET ON THE BACKSIDE OF THE HOOD

• When drilling the air outlet hole in the wall proceed in accordance with the scheme in the paragraph concerning the wall drilling.
• In case the connection is made with a ø 120 mm pipe insert the reduction flange 9 on the hood body outlet.
• Fix the pipe with an adequate quantity of pipe clamps. This material is not supplied together with the hood.
• Remove the charcoal filter if present.

AIR OUTLET ON THE UPPER PART OF THE HOOD

• In case the connection of the hood to the air outlet piping is made with a ø 150 mm pipe then use a rigid or a flexible pipe.
• In case the connection is made with a ø 120 mm pipe insert the reduction flange 9 on the hood body outlet.
• Fix the air outlet reduction 8c to the air outlet hole of the hood support with the screws supplied together with the hood.
• Connect the hood to the piping with a rigid or a flexible pipe.
• Fix the pipe with an adequate quantity of pipe clamps. This material is not supplied together with the hood.
• Remove the charcoal filter if present.

RECIRCULATION VERSION AIR OUTLET

• Insert PVC pipe 7 provided onto the Hood Canopy Outlet.

Hood body mounting
Ducting version

• In case the air outlet connection on the upper part of the hood has been chosen it will be necessary to remove the pre-cut piece.
• Lean the hood body on the support and fix it laterally with the 4 12b screws.
• Cover the screw seats with the plugs 13 supplied with the hood.

Recycling version

• Remove the pre-cut piece.
• Lean the hood body on the support and fix it laterally with the 4 12b screws.
• Cover the screw seats with the plugs 13 supplied with the hood.
• Place the direction grid 8 on the pipe and make sure that it is correctly installed.
• Fix the direction grid 8 with the screws 12e supplied together with the hood.
• Make sure that the charcoal filters are present.

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.
• Open the lighting unit by pulling on the notch.
• Remove the filters one at a time by pushing them towards the back of the group and pulling them down at the same time.
• Be sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan.
• Connect the control connector Cmd.
• Connect the Spotlights connector Lux to the socket provided behind the lighting unit cover.
• Replace the filters, make sure that the handle is visible on the outside, and reposition the lighting unit. Make sure that the catch is locked into position correctly.

USE

Control panel

turned off (Motor and Lights), to turn the Activated Charcoal Filter alarm on. The relevant LED flashes twice to confirm.
To turn the alarm off, press the button again and hold for at least 3 seconds. The relevant LED flashes once.
T3| Fixed| Turns the Motor on at speed three.
–| Press and hold the button for approximately 3 seconds, with all the loads turned off (Motor and Lights), to perform a reset of the Filter saturation alarm. The LED SI flashes three times.
T4| Fixed| Turns the Motor on at INTENSIVE Speed.
This speed is timed to run for 6 minutes. At the end of this time, the system returns automatically to the speed that was set before. If it is activated with the motor turned off, the hood will switch to OFF at the end of the time.
–| Press and hold for 3 seconds to enable the remote control, indicated by the LED flashing twice.
Press and hold for 3 seconds to disable the remote control, indicated by the LED flashing just once.
Si| Fixed| Signals the Metal Grease Filter saturation alarm, indicating that it is necessary to wash the filters. The alarm is triggered after the Hood has been in operation for 100 working hours.
Flashing| When this is activated, it signals the Activated Charcoal Filter saturation alarm, indicating that the filter must be changed; the Metal Grease Filters must also be washed. The Activated Charcoal Filter saturation alarm comes into operation after the Hood has been working for 200 hours.

CARE AND CLEANING

REMOTE CONTROL (OPTIONAL)
This appliance can be commanded using a remote control, powered by a CR2032 type 3 V battery (not supplied).

• Do not place the remote control near heat sources.
• Do not discard the batteries with normal waste, they must be put into specific containers.

Metal grease filters
These can be washed in the dishwasher, and need to be cleaned whenever the S1 Led comes on or at least once every 2 months use, or more frequently if use is particularly intensive.

CLEANING THE FILTERS

Resetting the alarm signal

• Turn the Lights and the Suction Motor off.
• Press T3 and hold for at least 3 seconds, until the LED flashes three times in confirmation.

Cleaning the Filters

• Open the lighting unit by pulling on the notch.
• Remove the Filter, pushing it towards the back of the unit and at the same time pulling downward.
• Wash the filter without bending it, and leave it to dry thoroughly before replacing it (if the surface of the filter changes color over time, this will have absolutely no effect on its efficiency).
• Replace, taking care to ensure that the handle faces forwards.
• Replace the filters and reposition the lighting unit.
  Make sure that the catch is locked into position correctly.

Activated Charcoal Filter (Recirculation Version)
This cannot be washed or regenerated and must be changed when led S1 starts to flash, or at least once every 4 months. The Alarm signal, if it has been activated, only appears when the Suction motor is turned on.

Activating the alarm signal

• In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date.
• Turn the Lights and the Suction Motor off.
• Press button T2 and hold it for 5 seconds until the LED flashes twice in confirmation:

CHANGING
Resetting the alarm signal

• Turn the Lights and the Suction Motor off.
• Press T3 and hold for at least 3 seconds, until the LED flashes three times in confirmation. Changing the Filter
• Open the lighting unit by pulling on the notch provided.
• Remove the Metal Grease Filter
• Remove the saturated Activated charcoal filter, using the hooks provided.
• Fit the new Filter, hooking it into place.
• Fit the Grease filter and the Light Unit back into place.

Lighting unit

• For replacement contact technical support (“To purchase contact technical support”).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>