techtron Lite 2000 Electric Scooter Instruction Manual

techtron Lite 2000 Electric Scooter

Welcome to techtron® by combining passion, drive and intellect with market- leading research and cutting-edge technology, we innovate and deliver premium quality products that excite, inspire and challenge the sector. Striving for perfection, embracing new ideas and investing in the future is our ethos.

Product and Accessories

• A Brake lever
• B Accelerator
• C Folding hook
• D Collar clamp
• E Folding pedal
• F Atmosphere lights
• G Kickstand
• H Power button
• I Charge port
• J Motor wheel
• K Rear brake
• L Reflector

Assembly

1. Slightly loosen the hex bolts on the collar clamp with the M6 hex key.
2. Insert the standpipe into the collar clamp.
3. Park with the kickstand. Step on the footboard, hold the handlebar and push forward to unfold the scooter.
4. Tighten the bolts on the collar clamp with the M6 hex key.
5. If the brake is too tight or loose,you can thread in/out the brake cable adjuster.

Charging

To charge the techtron® eScooter, simply open the rubber stopper on the side of the footboard and connect the power supply. Then plug in the power supply and switch on the power. Please allow three hours for the eScooter’s battery to fully charge.

When the eScooter’s battery is fully charged, the charge indicator on the plug will change from red to green. After charging, please ensure you replace the stopper to prevent water damage.
Children should be supervised at all times and should not touch the device whilst charging.

Functions

Power button
To power the eScooter ON/OFF, press and hold the main power button located on the side of the footboard for two seconds.
The atmosphere lights along the side of the scooter can also be controlled with a single press of the power button.

Riding modes
The techtron® Lite 2000 comes with two factory default riding modes: Turbo and Cruise. These can be determined by the power light status, detailed in the table below. In Cruise mode the scooter will hold it’s speed without the need for the accelerator to be pressed. With Turbo mode activated the scooter will gradually slow and stop if the accelerator is released.

For added safety, the techtron® smart app can be used to limit each speed mode, in order to best suit your child’s age or ability. As they further advance their riding skills the scooter’s speed can then be increased to the Lite 2000 model’s actual maximum: 18km/h.

Factory default settings

Riding mode| Maximum speed| Power light
Turbo| 14km/h| Fast blinking
Cruise| 7km/h| Slow blinking

Accelerating and decelerating

Action| Cruise mode| Turbo mode
Accelerate| Kick off to go, then press the accelerator
Decelerate| Use front/rear brakes| Release accelerator or use front/rear brake

Battery indicator
The power button displays current charge status (see table below). When an error occurs, the battery/mode indicator will flash and an alarm will sound.

Charge status

Green| 100% – 51%
Yellow| 50% – 21%
Red| 20% – 1%

Power saving
The eScooter will power down automatically after three minutes when not in use.

Product registration
For exclusive offers, product support and information on thelatest techtron® innovations, register your product by completing the form on the website with your serial number and details – www.techtron.co

techtron® Smart App

Your eScooter can be configured using the techtron® smart app.
Use it to set up your desired settings such as riding mode and speed limiter.
You can even lock the scooter to prevent unauthorised access.
Please note – the eScooter will remember all settings applied in the techtron® smart app even when Bluetooth® is disconnected.

Download to your smart device via the Apple App Store or Google Play.

1. Home screen
   View the remaining range of your eScooter, so you can plan your journey.
   Lights – Turn the atmosphere lights On/Off.
   Settings – Access further controls.
   Connection – Discover and pair your eScooter to your smart device.
   Riding mode – Toggle between riding modes.
   Trip info – View the latest trip information.

2. Settings
   Unit – Change the unit of measurement used to display your speed from km/h to mph.
   Riding mode – Choose your preferred riding mode.
   Cruise/Turbo mode speed limit – Control how fast the scooter can go if being used by children.

3. Trip info
   View your eScooter’s latest trip information, anything from total driving time to voltage and power statistics.
   The device firmware can also be upgraded by the user from this menu (internet connection required).

Maintenance and Warranty

Cleaning and storage
Use a soft cloth dipped in a small amount of water to wipe the eScooter; for any difficult to clean areas, you can use toothpaste and gently brush with a toothbrush, then use a damp cloth to clean.
Do not use alcohol, petrol, kerosene, or other corrosive, volatile chemical cleaning solvents, as this will seriously damage the appearance and internal structure of the body. Do not use pressure washers to clean. Ensure that the charging cable has been unplugged and the rubber stopper on the charging port is closed. Otherwise, there may be a chance of electric shock or serious failure due to internal water intake.

Warranty policy
techtron® offers a one-year guarantee on rechargeable batteries. Two-year guarantee
against parts and/or manufacturing defects, Terms & Conditions/Exclusions apply,
please see website for further details.

Product registration
For exclusive offers, product support and information on the latest techtron® innovations, register your product by completing the form on the website with your serial number and details – www.techtron.co

Battery maintenance and disposal
Do not touch the battery contacts, and do not open or expose the shell. Avoid metal objects touching the battery contacts, as this will cause a short circuit, damage to the battery, or even personal injury.

Please refer to the model specifications in this manual for your eScooter’s charging requirements. Only use a charger with the correct voltage otherwise there will be a risk of damage to components or fire.

Ensure batteries are disposed of responsibly. Recharge the battery and store it after use, to preserve battery life. Do not place the battery in high temperatures higher than 50°C or below -20°C, or it may lead to battery failure, overheating, or even risk of fire.
Always store in a cool dry place fully charged. A battery will be at optimum performance at a standard room temperature.
Warranty may be invalid if the battery is removed.

Children should be supervised at all times.

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environment safe recycling.

Rider Guidance, Safety and Specifications

Helmets and clothing
Wearing cycle helmets are recommended when riding an eScooter, but they are not a legal requirement. Always make sure that your cycle helmet conforms to current regulations, is the correct size, and is securely fastened. Wear lightcoloured or fluorescent clothing so that other road users can see you at night or whenever visibility is poor.

As with any vehicle, the faster the user is travelling,the more braking distance is required. Please respect pedestrians’ right of way when riding the techtron® eScooter.

Riding safely
Please check the eScooter before riding.
Check for loose parts and general tyre wear and tear.
Always start the eScooter by pushing off with your foot first, this reduces the start load on the motor, ensuring a longer battery life.
The techtron® eScooter is designed to perform best on smooth dry surfaces, therefore avoid riding on uneven gravel, sand, grass, slick or wet surfaces.
Never ride over curbs or jump. The eScooter is not designed for this type of riding and any damage caused to the eScooter while riding in this manner will void the warranty.

techtron® accepts no liability for any injuries caused to rider or damage to property which may arise while riding the eScooter. Never ride the scooter with more than one person, as this may lead to loss of control. It is the rider’s responsibility to ensure they comply with all local laws and regulations that may apply while riding the eScooter.

Model specifications

Any enquiries regarding maintenance, accessories, security or warranty, please visit the techtron website: www.techtron.co or email us: info@techtron.co

Rules of the road and licensing guidance
For the latest up-to-date safety, licensing guidance and rules of the road for UK eScooter
users, please consult the UK Government website: www.gov.uk/guidance/e -scooter-trials-guidance-for-users

For further information and advice you can find us at: techtron® Unit 2, Jowett St,
Bradford, BD1 2JX. UK.
e: info@techtron.co
t: 0203 307 6776
w: techtron.co
Research & Development 2100 Geng Road, Suite 210,
Palo Alto, California, 94303 USA.
e: info@techtroncalifornia.com w: techtroncalifornia.com
techtron® is a division of Multibrands International Ltd.

References

• techtron® electric scooters
• techtroncalifornia.com
• E-scooter trials: guidance for users - GOV.UK
• techtron® electric scooters

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>