WILIT F3Q LED Table Lamp User Manual
- June 6, 2024
- WILIT
Table of Contents
F3Q
LED TABLE LAMP
User Manual
Product Introduction
Product Features
- QI Wireless charger: charge for electronic products that comply with QI protocol.
- Adjust the brightness by rotary encoder, three color temperature can be changed freely.
Instruction
Press/rotary switch
Short press: cold , warm and Cold&warm light, turn-off switched cyclically.
Rotary switch: adjust the brightess in clockwise direction to increase and
in anticlockwise to decrease.
Please read the instruction manual carefully before using the product.
Specifications
| Rated Voltage | 12V/1A | Ra | >80 |
|---|---|---|---|
| Rated Power | 12W | Luminous flux | 150-270Lm |
| CCT | 5500±500K ; 3000±280K ; 4 200±400K |
Warranty Card
Applicable for
Since the date of purchase, free service is guaranteed for one year under
normal use. If beyond the warranty period , the cost of components will be
charged.
If the replaced components service are required, the cost will be charged
according to our price list of spare parts maintenance.
Under the following cases, the one-year free warranty service is not
available.
- Damage caused by non-normal use and natural disasters, such as earthquake and rat disaster.
- Unauthorized maintenance, misuse, collision, negligence, abuse, accident, alteration, incorrect use of accessories that do not belong to the product.
- Information in warranty card is not complete, such as purchase date and seller’s seal and chop are not included.
- Special environment is not included in warranty scope, such as wet, sulphur areas, high salinity areas beside the sea, and corrosive areas.
- Not following the instructions.
- Special offer.
In order to avoid damage during transportation, please pack the products
carefully when retuming for maintenance.
The manufacturer shall not be responsible for the breakdown of the product
caused by customers’ dismounting.
Important!
Thank you for purchasing our products.
To ensure your rights, please fill in this form carefully, thank you.
Name……………………………………………………………………………..
Address………………………………………………………………………….
Telephone No………………………………………………………………..
Invoice No…………………………………………………………………….
Purchase Date……………………………………………………………….
Item No………………………………………………………………………..
Distributor……………………………………………………………………
Note: this column requires the distributor’s seal!
Warning: The light source of this lamp is not replaceable, the whole lamp should be replaced when the light source reaches the end of its life time.
Warning: Please keep the warranty card for repair presentation
FCC Statement
This device complies with part 15 and part 18 of the FCC Rules. Operation is
Subject To the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not explicitly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 and part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and candidate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Increase the separation between the equipment and any other radio device.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ISED Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 10 cm surrounding the device and 10 cm above the top surface of the device must be respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>