ZCGIOBN B0CMLQJZZP 1000 ANSI Movie Projector User Guide
- June 14, 2024
- ZCGIOBN
Table of Contents
ZCGIOBN B0CMLQJZZP 1000 ANSI Movie Projector
Thank you for purchasing the product
Important Safeguards
Installation
To get a better watching, please use this projector while drawing the curtain
or in a dark room. Please use the projector carefully, dropping or crashing
may damage parts or result in blurred images and abnormal displaying.
Power
Be careful while using the power cord, and avoid excessive bending; the damage
of the power cable may cause electric shock and fire. It is better to unplug
the power cord after power off.
Cleaning
Unplug the power cable first. Clean the shell regularly with a damp cloth,
neutral detergent can be used. Please use a glasses cloth or lens paper, avoid
scratching the lens. Please clean the projector’s vents and speakers regularly
with a banister brush, or the Ventilation will be blocked.
High-Temperature Attention
While projection or just finishing, the exhaust port nearby will be very hot
and, if touched it, would get scalded. While projection, please do not look at
the lens directly, or may hurt your eyes.
Warm Tips
Do not disassemble the projector for there will be a risk of electric shock,
and the unauthorized disassembling will void the warranty. Please do not put
any liquid or heavy stuff on the projector. To ensure the stability of heat
dissipation, please open the height bracket in the bottom of the projector
before starting.
Projector Knowledge
The projector can input high-definition video signal and composite video signal, and support stereo audio signal input and output. Please refer to the following figure to connect the projector and other equipment according to your own needs.
- Lens
- Control panel
- Vents
- AC-in
- Manual focus
- RJ45 network cable interface
- 3.5mm audio out
- AV port
- VGA port
- HDMI port
- USB port
How to maintain the Air Purifying Filter
For better long-term use experience, the projector adopts a new design of Air
Purifying Dustproof Optic Engine. To ensure the performance of air purifying
of the filter, please clean or replace the filter if necessary. Lightly press
the bottom of the air inlet, the filter will pop out. You can use a wool brush
to gently sweep away the dust on the surface of the filter element. Depending
on the frequency of use, it is recommended to replace the filter element every
3 to 6 months. The system will also pop up a tip to remind you to replace the
filter element after the accumulative use time reaches 500 hours. Please
replace the filter element according to the tips. Note: The filter element is
designed with special material and cannot be washed with water, otherwise the
adsorption performance of the filter element will be damaged and the service
life of the machine will be affected.
Remote Control
- Power key
- Settings
- Arrow keys
- Return key
- AF micro adjustment
- Source
- Menu
- Main interface
- Volume+/-
- Mute
Projector Installation
Standard Setting
Please refer to the following table to adjust your picture size and distance.
(from the lens to the screen).
Picture size (inch)
| Projection distance (16:9)
---|---
(cm)| (feet)
36| 95| 3.12
60| 196| 6.43
72| 236| 7.74
84| 275| 9.02
100| 328| 10.76
120| 386| 12.66
150| 480| 15.75
Please allow 5%-10% to the image sizes and projection distance in the table above {due to measured manually). If the distance is less then Min. data or more than Max. data, the image maybe blurry.
Installation Method
Contact a professional installer to mount this projector to a ceiling. Follow
the instructions below for the correct projector positions.
Warning
- The projector may be damaged beyond repair if it is incorrectly mounted on a ceiling or on a surface.
- The projector should only be used in an environment where the temperature does not exceed the range of 5°C -35°C . Projector malfunction may occur if this is not adhered to.
- Malfunctions may occur if the projector is subjected to dusty, wet, moist or smoky conditions.
- Poor ventilation could cause overheating which could lead to damage to the projector as well as a life-threatening situation.
Turn the Projector On/Off
When the projector is connected to a power source, the projector enters into
standby and the power indicator is red.
- Switch on: Press the power key on the body or the power key on the remote control, the indicator will turn green and enter into the working state.
- Switch off: In the working state, press the power key on the body or the power key on the remote control, the indicator changes from green to red, and the projector is turned off.
Use of the Projector
How to Switch Source
Select and enter “SOURCE” on the SETTING interface, then select the source you
want at the bottom of the page: AV/ VGA/ HDMI 1 / HDMl2 / USB.
How to Use Image and Audio Settings
Select and enter “SETTINGS” on the SETTING interface, then select “Image” for
image settings and “Audio” for audio setitngs.
Image: Image mode I User settings/ Advance setting / Zoom mode/ Reset.
Audio: Audio Mode/ Volume/ Equalizer Detail / Advance setting / ARC.
How to Play Files in USB Drive
Insert the USB device, and select “YES” in the pop-up interface. Or select and
enter “USB” on the SETTING interface, and browse the files in your USB device.
Multimedia Format Supported in USB Drive
- Video Format: 3GP/AVI/FLV/MP4/MPG/VOB/TS/M2TS/DAT/MKV
- Audio Format: MP3/APE/AAC/FLAC/OGG[l/vAV[l/vMA/MID/DTS/M4A
- Image Format: BMP/JPG/PNG/JPEG
- Text Format: TXT/PDF/DOC/X LS/PPT
How to Use Projection Settings
Select and enter “SETTINGS” on the SETTING interface, then select “Projection
setting”. 4D keystone: Manually adjust the four corners through the arrow keys
until the projection image becomes rectangular.
- Zoom In/Out: Zoom out the image or enlarge the image to its original size.
- Quick keystone: Adjust vertically/ horizontally until the projection image becomes rectangular.
- Projection Mode: Front-Projection/ Rear-Desktop/ Front-Ceiling/ Rear-Ceiling.
Wired Connect to the Internet
Connect the network cable to the RJ45 port, the projector will automatically
connect to the network.
Wireless Connect to the Internet
Select and enter “SETTINGS” on the SETTING interface, then select “Network”–>
“Wireless network”, switch on and select the network on the list, fill in the
password, and complete the connection.
How to Connect Bluetooth
Select and enter “SETTINGS” on SETTING interface, then select and enter
“Bluetooth”. Turn on the “BT Switch”, then select and enter “Management”,
search and pair with Bluetooth device.
How to Use Screen Mirroring
Go to the APPS interface, select and open the corresponding screen mirroring
App for your device, and then set up the connection in the order in the
interface. Wi-Fi Display Sink for Android devices; AirScreen for iOS devices.
Connection Steps
- The projector and the Android or iOS device should be connected to the same WiFi or Network.
- Turn on “Wireless Display”/ “Wireless Projection” on the Android device, or “Screen Mirroring” on the iOS device.
- Select the corresponding projector device name to connect.
Boot Upon Power Restore
Select and enter “SETTINGS” on the SETTING interface, then select and enter
“General”, and turn on the “Boot Upon Power” switch. Once the power cable is
connected, the projector will turn on and enter into the main interface
directly.
- You can also use a timing switch or other smart device to achieve a timed start of the projector. The timing switch device needs to be prepared by yourself.
Language and Time Zone Setting
Select and enter “SETTINGS” on the SETTING interface, and select and enter
“General”.
- Language Setting: Select and enter “Language”, and choose the language you want.
- Time Zone Setting: Select and enter ”Time”, and choose the time zone you want.
Troubleshooting
- The indicator light does not work when the power switch is turned on.
- The power cable is not connected properly. Reconnect the power cable or change the power cable.
- The power switch is faulty. Contact your seller for help.
- The power board is faulty. Contact your seller for solutions.
- The projector does not work when using the remote control.
- The power switch is turned off.
- The remote control has no batteries or the batteries are low.
- The remote control is not being aimed at the IR receiver.
- The IR receiver is under strong light.
- The remote control is defective, contact your seller to get a new one.
- No image.
- The input source may be incorrectly selected.
- No input signal.
- The input cable is not connected.
- Under PC mode make sure the video output frequency is between 50-60Hz.
- The lens may be blocked, check if there is something in front of the lens or lens cover isn’t taken off.
- Auto-off.
- The projector’s ventilation is blocked.
- The voltage is not stable.
- The projector is overheated. Check if the cooling fan is working.
- System freeze up.
- Android OS may have a bug, contact your seller for technical support.
- App contents cannot be mirrored.
- Copyright-protected App content on Netflix, Prime Video, Hulu, or any similar video
Warranty Card
- Buyer Information
- Name/Company:
- Telephone:
- Address:
- Fax No.:
- Product Purchased:
- Model No.:
- Series No.:
- Seller Store Name:
- Date of Purchase:
- Manufacturer Information:
Guangzhou Caiwei Optoelectronics Co., Ltd Address: Room 201-401 Building 3, No. 89, Majun Street, Dongchong Town, Nansha District, Guangzhou, China 511453
- Official Website: www.caiweiinc.com
- Service Email: caiwei@eug.net.en
Thank you for purchasing the projector. From the date of purchase, we offer a year warranty on the projector and a 6-month warranty on the bulb. When you encounter a problem with the projector, contact your seller or send an email to the above email address with your ORDER NUMBER and the purchase platform or website.
IMPORTANT NOTE
All warranty policies and warranty terms are limited to brand-new products
that are bought from official channels, second-hand products, or purchased
from other unofficial channels are not covered by the warranty, and no
warranty service will be provided.