YOKOMO YD-2ZX 1/10 2WD RWD Drift Car Kit Red User Manual

YOKOMO YD-2ZX 1/10 2WD RWD Drift Car Kit Red

Thank you for purchasing this Yokomo product.
This high performance competition kit has been proudly manufactured by Yokomo – World Champion R/C car manufacturer.
Proper assembly of this product will provide fun, safe enjoyment.

PRECAUTIONS FOR SAFE ENJOYMENT OF YOUR R/C CAR
For children under the age of 13, parental guidance is recommended when running.

ASSEMBLY PRECAUTIONS

• Do not assemble around small children. The parts can be dangerous if accidentally swallowed.

• Check the contents carefully before assembly. Please contact Customer Support if you happen to notice any defective or missing items.

• You will find the assembly process much easier by carefully reading through the manual, and familiarizing yourself with the instructions.

• Many different tools are required during assembly. For safety purposes, please use suitable tools.
  Exercise extra caution when using a sharp tool such as a hobby knife.

• Many different materials are used for the parts. Use extra care when handling parts with sharp edges, such as machined metal parts.

• When cutting plastic parts, watch for any flying parts.

• Try to assemble any rotating parts or drivetrain parts as smooth as possible.

• Bundle wires neatly away from the ground or any moving drivetrain components.
  Make sure that all wires are properly connected to prevent shorting.

• Unnecessary modifications may be unsafe and hinder performance.

• Always paint in a well ventilated area away from flames.

PRECAUTIONS BEFORE RUNNING

• Yokomo R/C cars are built for competition use, and some models may exceed speeds of 40km per hour. Practice common sense and run the car in open safe places, or R/C car tracks.
• Do not run the car on public roads with high amounts of traffic, or in areas that may cause an inconvenience to people in that area.
• R/C cars are controlled using a radio frequency. In a worst-case scenario, radio interferences may cause loss of control.
• If others near you are running R/C cars, confirm that they are not running on the same frequency.
• R/C cars do not like water. Avoid running on rainy days, or areas with water puddles. Exposure of the electronics to water may cause loss of control or damage to the electronics.
• The drivetrain of an R/C car consists of many moving parts like gears, belts, shafts, and tires. Avoid touching these areas when the battery is connected.
• Many parts of an R/C car will become hot after running. Allow the parts to sufficiently cool before conducting any maintenance.

BEGINNING A RUN

1. Place the R/C car on a stand so the wheels are off the ground.
2. Confirm that the speed controller switch is OFF, and connect the motor and battery.
3. Extend the transmitter antenna and turn the switch ON. (It is unsafe to use a transmitter with low voltage. Make sure that the transmitter batteries are good before running.
4. Turn the speed controller switch ON.

FINISHING A RUN

1. Turn the speed controller switch OFF.
2. Disconnect the battery.
3. Turn the transmitter switch OFF, and retract the antenna.

BATTERY USAGE

（Carefully read the instruction included with the batteries）

• When charging batteries, make sure that the surrounding area is void of anything highly flammable. Also avoid charging in high-temperature locations.

• When charging batteries, frequently monitor the charging status. In a worst case scenario, overcharging a battery may cause it catch on fire. If the battery reaches 50 degrees Celsius or more, stop charging.

• Batteries will become hot after running. Continuous use of the battery pack may result in damage to the cells. Allow the battery too cool down before
  re-charging.

• Please do not discard old battery packs in the trash. Although inconvenient, please locate a battery disposal center.

MOTOR USAGE

（Carefully read the instructions included with the motor.）

• Connecting a 7.2V battery directly to the motor can be very dangerous. This may cause the internal parts of the motor to break apart, causing some parts to fly out of the motor. To break-in the motor, safely secure the motor and run the motor at about 3-5V.
• Motors require periodic maintenance. Slower speeds and decreased run times may indicate a worn-out motor. Periodically clean the motor and change the brushes when needed.
• Choose a gear ratio that matches the power characteristics of the motor. Using a gear ratio unsuited to the characteristics of the motor will not only prevent the motor from performing at its optimum, but may even cause damage to the other electronics.
• Motors will generally become very hot after running.
  Continuous running will reduce the life of the motor. Allow the motor to sufficiently cool between each run.

ACCESSORIES AND TOOLS NEEDED FOR KIT ASSEMBLY

ADDITIONAL ITEMS REQUIRED FOR USE (NOT INCLUDED IN KIT)
TOW CHANNEL R/C SURFACE RADIO SYSTEM AND LOWPROFILE SERVO, ELECTRONIC SPEED CONTROL
7.2V BATTERY PACK (Li-Po Shorty Battery ・ 1S-Size)
BATTERY CHARGER
MOTOR
BODY SPRAY PAINT

ASSEMBLING TOOLS REQUIRED. (NOT INCLUDED IN KIT)

• HEX WRENCH
• NUT DRIVER
• SCREW DRIVER(SMALL)
• NEEDLE NOSE PLIERS
• SIDE CUTTER
• SCISSORS
• BODY REAMER
• QUICK DRYING GLUE
• HOBBY KNIFE

TOOLS (INCLUDED)

For assembly, follow the figures and the instructions closely so that your machine will perform at its best!!

INSTRUCTIONS

1. Main Chassis Assembly
   For shorty Li-Po ( 1S-size ) battery, low profile servo use only.

2. Slide Rack, Steering Rod Assembly
   

3. Gear Diff Assembly
   

4. Gear Box Assembly
   

5. Servo Installation If you are using a servo other than the low profile servo, please prepare the following parts separately.
   Y2-003ADF
   Y2-118S
   Y2-202SM
   

6. Servo Horn Installation

7. Slide Rack Installation

8. Front Shock Tower Assembly

9. Rear Shock Tower Installation

10. Front Arm Installation
    
    

11. Steering Block Installation
    

12. Rear Hub Carrier Assembly
    

13. Rear Hub Carrier Installation
    

14. Rear Suspension Arm Installation
    

15. Front & Rear Shock Assembly
    

16. Bumper, Body Post Installation
    
    ※Please Note※
    When making a rear mounting hole in the body, make it 4.5 mm behind the marking position.

17. Diffuser Installation
    

18. Receiver, ESC Installation
    

19. Upper Deck, Motor Installation
    

 | 19T| 20T| 21T| 22T| 23T| 24T| 25T| 26T| 27T| 28T| 28T| 30T| 31T| 32T| 33T| 34T| 35T| 36T| 37T
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
84T| 11.50| 10.92| 10.40| 9.93| 9.50| 9.10| 8.74| 8.40| 8.09| 7.80| 7.53| 6.28| 7.05| 6.83| 6.62| 6.43| 6.24| 6.07| 5.90
20. Battery Holder Installation

21. Tires Assembly, Wheel Installation
    Tire and wheel, mounting tapes.( Sold separately )
    

22. Battery Installation (Vertical Type)
    The battery can be mounted to the vertical type.
    When mounting to the vertical type, refer to the diagram shown below.
    

YD-2ZX Exploded View

SETTING

MY Yokomo User Registration
(Request for Web Entry)
https://teamyokomo.com/mypage/

thank you very much for purchasing Yokomo products this time. Yokomo hopes to develop and manufacture better products and provide fulfilling services based on valuable comments from customers. Please continue your favors towards user registration to MY Yokomo.
For the user registration, please go to MY Yokomo registration page from QR code or PC URL described on this form and enter necessary information by “click here”, name here etc.” By registering, you will be able to use services such as periodic e-mail newsletters and various benefits / information.
We will strictly control personal information that we have kept in compliance with the laws and other guidelines established by administrative agencies.

TEL 029-896-3888
FAX 029-896-3889
YOKOMO LTD.
4385-2 Yatabe, Tsukuba City, Ibaraki Prefecture,
305-0861.JAPAN
TEL +8129-896-3888
FAX +8129-896-3889

YOKOMO LTD.
4385-2 Yatabe, Tsukuba City, Ibaraki Prefecture,
305-0861.JAPAN
TEL +8129-896-3888
FAX +8129-896-3889

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>