JETBeam EC26 EDC 3600LM Tactical Flashlight User Manual

JETBeam EC26 EDC 3600LM Tactical Flashlight

OVERVIEWS

• Please use good quality 18650 batteries such as brands of Samsung, Panasonic, Sanyo, Sony or LG high current output bare battery (without protection PCB board on), It’s better use battery whose current over 12A.
• EC26 is a high-power flashlight, DON’T flash to people, moving cars, and inflammable stuff.
• When the flashlight is running in high output mode, the head will become hot but It’s normal, the temperature may be over 50℃ during lasting use in warm environments, take good necessary protective measures.

Features

• Compact and easy carrying
• Uses 4*XP-L HI LED, lifetime over 50,000h
• Max 3600LM output, Max 268m beam throw
• When the flashlight is at the low brightness output, max runtime 50 days
• Rich light output modes for different applications or custom spots
• Battery anti-reverse protection circuits
• Magnet tail cap for hand free
• Battery power detection and temperature check

Specifications

• LED:4*CREE XP-L HI LED
• Max output: 3600LM
• Reflector: Lens
• Glass: Filmed mineral scratch-resistant glass
• Material: High-strength aerospace aluminum alloy
• Finish: HAIII hard anodizing finish
• Battery:1*18650
• Switch: side switch Size: 98mm (length), head: ¢30.8mm, tail: ¢25mm
• Weight: 75g(exclude battery )

UI interface

• A.In default EC26 sets in stepless dimming mode and can start the ultra-bright mode instantly.
• B.If you like step dimming, you can select the conventional mode change style and choose the output mode quantity you prefer.
• C.Instant tactical mode is useful to emit signs, quick or short time to light up the target., power off to exit tactical mode.
• D.Muggle mode can lower the output to avoid hurting his eyes when the flashlight is lent to somebody.
• E.Owns lock function for safety, but can use the instant tactical low output as well.
• Others: battery detection, sunset, beacon, tactical strobe, party flashing, bike flicking, candlelight, lightning, and storm.

Output & Runtime

FL1 STANDARD

| High| Low|
---|---|---|---
| 3600LM| 0.1LM| The above data complies with American National Standard Institute ANSI/NEMA FL1 Standard. Data was obtained by using one SONY VCT6 3.6V 3000mAh rechargeable 18650 battery in lab. Different data may result when using different batteries.
| 2.9h| 50 days
| 17956cd
| 268m
| 1.5m
| IPX8

Special attention: the temperature protection limit should be adjusted to more than 70 degrees for testing, in order to get the maximum parameters. The default setting is 45-degree protection. When the maximum brightness is turned on, the power output will be reduced slowly, and the maximum parameter can not be measured.
Operation of fleshlight insert the battery

1. Remove the tail cap and put the battery inside
2. The positive electrode of the battery towards the flashlight head ( the end where the LED is located
3. Cover tail cap back and fasten tight

Operation

Note : The following operation define as: digit+C=click times, for instance, 3C= 3 single clicks; Digit+H=(digit-1) click times+1 press and hold, for instance, 5H=(5-1=4) clicks+1press and hold

1. Single click power on/power off

2. When powering on, 3C goes to mode convert: stepless dimming-step dimming

3. When powering on, 4C goes to the mode convert set, see the details.

4. Long press to increase the brightness or decrease brightness

5. Double clicks go to Ultra-bright mode.

6. When power off, 4C goes to lock or unlock status

7. When power off, 5C goes to tactical mode, unscrew the battery in 2 seconds to exit tactical mode.

8. When power off, 6C goes to Muggle mode/exit the Muggle mode(Muggle is a mode to limit brightness output for safety)

9. When power off, 3C goes to flick mode:  a: When flick mode is on, double clicks go to Battery detection- Sunset-Beacon-Temperature check b. On Beacon mode, 4C goes to beacon set(see the details) c. On Temperature check mode, 4C goes to temperature set(see the details)

10. When power off, 3H goes to flashing mode. a: When flashing mode is on, double clicks go to Candle light-Bike- Party-Strobe-Lightning b. On flashing mode, long press to increase brightness or decrease brightness c. On Candle light mode, 3C goes to increase the running time, every 3C can extend 30 minutes running time, Max 4.5 hours.

The voltage level of general lithium battery

Note: the load voltage is lower than the no-load voltage.

Ambient light brightness: when power off, 7C goes to light change: Off- Low-High-Flick

Ambient light color: when power off, 7H goes to light color change: Red- Yellow-Green-Cyan-Blue-Purple-White-Rainbow-Voltage

Default reset
Unscrew the tail cap, press and hold the switch, screw the tail cap tightly and press and hold the switch in 3 seconds

Set the light output
Whenever stepless dimming or step dimming, both can set the light output, people can set the lowest brightness (floor) and highest brightness(Ceiling), also the output mode quantity (only for step dimming). Whenever on any brightness output mode, 4 clicks goes to the present mode’s setup.

Regards the step-less dimming, there are 2 options:

1. Floor (default level=1/150)
2.  Ceiling(default level=130/150)

Regards the steple dimming, there are 2 options:

1. Floor (default level=20/150)
2.  Ceiling(default level=130/150)
3. mode quantity(default=7)

If want to set the floor output, please click the times you like the level on(total 150 level), for instance, 1 click for moonlight. If set the Ceiling output level, every click will decrease one level, for instance, 1 click goes for the highest level, 2 clicks go for 2nd highest level, 3 clicks go for 3rd highest level. The Ceiling level setup digit: 151*(target level)=click times, If want to set the ceiling output, please click the times you like the level at (default 130/150 level), Max 21 clicks goes for 130 level. If set the output mode quantity, the digit will be one of 2-150. If want to change the floor brightness in lowest output or ceiling in highest output, just click once is OK.

Temperature set

℃| ℉|
---|---|---
100| 212| Boiling water
60| 140|
55| 131|
50| 122| Touch limit
45| 111| [default]
40| 104|
37.4| 99| Barrel temperature
25| 77|
20| 68|
0| 32| Frozen water
Maximum temperature – 30°C = clicks

1. One-click says one Celsius degree when do temperature correction, for instance, 21℃=21 clicks.
2. Limit the Max protection temperature to avoid overheating,, if over 30 ℃, one click goes to increase one degree(default =45℃,15 clicks), for instance, want to set the Max temperature at 50℃, 20 clicks.

Beacon set
Click’s times say flick frequency, for instance, 4 clicks says flicks per 4 seconds in the cycle.

Protection function
The mainboard is designed by digital integrated circuit components own temperature and low voltage protection.

Light Maintenance

1. Take the battery out for storage if light will not be used for a long time
2. Keep the light away from heat, static electricity, and high humidity
3.  Clean the thread and conductive contact of light with a soft cloth. Lubricate the threads every 6 months

Warranty

We provide 60 months (5 years) of the warranty period for this product from the date of purchase in case defects are caused by material or workmanship with normal use. Necessary material and labor costs will be charged after this period

Free warranty does not cover any damages or failure if:

1. This product is disassembled or modified by anyone other than an authorized JE TBeam warranty technician.
2. This product is damaged by using the wrong battery or incorrect usage.
3. This product is damaged by defective batteries (such as battery leak).
4. Saltwater and corrosive damage to the unit.

Service

1. In need of warranty service, please contact your local official JETBeam dealer
2. To contact JE team, please refer to below information:Email:info@jetbeamlight.com Phone:+86-0755-27523445For the latest update, please visitwww.jetbeamlight.com

References

• JETBeam Electronic Technology Co.Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>