ASPEN HS605J1-L11-BG-1 Dimmable LED Indoor-Outdoor Black Smart Ceiling Fan Instruction Manual

ASPEN HS605J1-L11-BG-1 Dimmable LED Indoor-Outdoor Black Smart Ceiling

Fan

SAFETY PRECAUTION

IMPORTANT: PLEASE READ BEFORE INSTALLATION:

1. Before you begin installing the fen, shul power off at lye circuit breaker of the fuse box.

2. CAUTION: Read all instructions and safely information before installing your new fan. Review  assembly diagrams.

3. Make sure that all electrical connections are in accordance with National Electrical Code, ANSIINFPA 70 and local codes. Hire a licensed electrician if you ere unfamiliar with enshelling electrical wiring.

4. Make sure the installation site you choose allows 1he fan blades to rotate without any obstruc11ons. Allow a minimum clearance of 2.1m (7 feet) from 1h& floor end is inches from the tip of the blades to the well.

5. WARNING: To reduce the risk of fire, electric shock. or personal injury, mount to outlet box marked “”Acceptable for Fan Support of 15.9 K(j (35 lbs}or less· and use mounting screws provided with the outlet box.

6. CAUTION; To reduce the risk of injury, use only the screws provided with the outlet box in conjunction with the tock washers provided with the fan.

7. The outlet box and support structure must be securely mounted end capable of reliably supporting a minimum of 35 pounds. Use only U.L. listed outlet boxes marked •Acceptable for Fan Support of 15.9 kg (35 lbs) or less··.

8. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.

9. Do not insert anything into the fan blades while the fan is operating.

10. To change the direction of 1he rotation of the blades 1he fan must be in operation mode.

11. All set screws must be checked and retightened where necessary before Installat1on.

12. WARNING; To reduce the risk of personal injury. do not bend the blade bracket when installin9 the brackets. balancing the blades. or cleaning the fen. Do not insert foreign objects in between rotating fan blades.

13. CAUTION: To reduce 1he risk of electric shock, disconnect the electrIceI supply circuit to 1he fan before installing light kit.

14. After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment. Grounding conductor on one side of 1he outlet box end 1he ungrounded conductor on the other side of the outlet box.

15. The splices after being made should be turned upward end pushed carefully up into the outlet box. Conductor wiring identified as grounded is to be connected to a grounded conductor of power supply. Conductor wiring identified as ungrounded conductor is to be connected to an ungrounded conductor. Conductor wiring Identified for equipment grounding Is to be connected to sn equipment• grounding conductor.

16. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

17. This device may not cause harmful interference, and

18. This device must accept any Interference received. Including Interference that may cause undesired operation.
    WARNIMG: To reduce the risk of fire or electric shock, this fan must be installed with a general use, isolating well control/switch.

19. WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
    NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and sI1uatlons that may occur. It must l>e unders1ood 1hat common sense, caution and care are factors which cannot be built lento 1hls product. These factors must be supplely by the person (s) installing. caring for and operating the unit.

20. This product is suitable for use in damp locations.
    CAUTION: The light source is designed for this specific application and can overheat if serviced by un1ralned personnel. Ir any servicing ts required. the product should be returned to an authorized service facility for examination or repair.

BEFORE YOU START

Contact a licensed electrician if you are uncomfortable performing electrical work. A licensed electrician must install the fan if required by local code. Do not use the fan with a dimmer switch. Turn off power at breaker.

Tools and Materials Required

Product Instruction

Installation

installing Fan Blades:

• Locate 15 bled attachment screws with integrated washers in hardware peck. Secure each blade to the blade arm using the blade screws es shown in Fig 1.1.
• Fig 1.2 is 1he schematic calligram of the installed Ian blade arms. Repeal these steps for the remaining blades. Make sun all the screws are firmly tightened.

Installing the Prepared Fan Blade Arms:

• Fix the prepared blade arm to the motor assembly with tha blade arm screws as shown in Fig 2.1.
• Five blade arms installed.

• Remove 1he Light Assembly:
  Take out the light set from the package box end remove the lampshade by rotating it counterclockwise. and then remove the LED light kit out of the light kit pan as shown in Fig 3.2.

Installing the Light Kit Pan:

• Remove on& screw from the the center fixing plate of the motor assembly and loosen but DO NOT remove ThE other two screws. Push the light kit pan lo the fixing plate so thali the 1wo loosened screw heads fit into the keyhole slots.
• Feed the light wire connector plug from the fixing plate through center hole of the light kit pan. Turn the light kit pan clockwise. Re-install the screw that was removed. Make sure all the screws are firmly tightened.

installing the Light Kit:
Allow the llgh1 wire connector plug to come through the light kit. Install back the light Kit and the llgh1 kit Is magnetically attracted 10 the pan with the help of magnet.
Insert the light wire connector plug to the light terminal  block.

installing the Downrod
Assemble downrod as pictured in Fig 6.1 and Fig 8.2.
lnserl the downrod through the canopy ani:t wiring cover. (Please seleci the sullal)le length of roi:t for your ceiling.)
Note: If you choose to install a safety cable/chain onto your ceiling fan, you will also need to run it through the down rod prior to Installation.

Installing the Downrod
Press the motor power cord and safety cable through the down rod. (See Fig 7.1)

Note: Take out the end of lhe safety cable from the downrod before sliding the downtod inlo the plastic head of the motor assembly. Align the holes, secure with rod screws and washers in opposite directions from each o1her(2 sets on each side )end make sure the screws end washers are tightened firmly with a screwdriver. Remove the screw already set inside of the motor shaft, then secure the safety cable into the motor shan firmly by this scniw. (See Fig 7 .2 & 7 .3)
Slide the wiring cover down until it rests on top of the motor assembly. {See Fig 7.4)

Fig 7 .5 shows the assembly of down rod part is finished.

Installing the Mounting Bracket:
Install the mounting brackst to the ceiling box, as shown in Fig 8.1 below. Rotate the mounting bracket in different directions so that the bracket mounting holes match the screw holes of the ceiling box.

Note: This mounting bracket is a standard cable box.
If the mounting bracket is installed at the outlet box, it should be installed on the outlet box with two screws matching the outlet box itself. as shown in Fig 8.1.
Note: DO NOT use the plastic outlet l)ox. Use only U.L. llsteel outlet l)oxes merked•Acceptable tor Fan Support of 15.9 kg (35 lbs)or less··.
This bracket can also be mounted to the wooden ceiling beam, and then the four ST5x24 screws can be used to lock the corresponding holes on the left snd right sides of the bracket.
Note: The wooden ceiling beam musl meet the tensile test 0130KG for installation, es shown in Fig 8.2. II ls also possible to Install the mounting bracket dlrec11y to the concrete celling and Install four screws (not included) to the left alld right correspollding holes of the bracket to lock the ceiling.
If you have an angled or vaulted ceiling: (Fig 8.3)

• When installing the mounting bracket. the bracket groove is upward.
• You will need a longer down rod.
• lf your ceiling angle is greater than 27° . you will also need an Angled Mounting KiT.

Hanging Ceiling Fan & Installing Power Adapter & Wiring the fan: 
WARNING: To reduce the risk of fire, electric shock or other personal injury, mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box.
WARNING: Check to see that all connections are tight, including ground, and there are no visible bare wires at the wire nuts (except for the ground wire).
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
WARNING: To avoid any electrical shock, be sure electricity is turned off at the main fuse box before wiring. Install the ball end of the downrod into the opening of mounting bracket. Rotate the downrod until the tab in the mounting bracket is seated in the slot in the downrod ball as shown in the enlarged image of Fig 9.1. Attach the safety cable/chain to a ceiling joist or to a metal brace mounted to two ceiling joists, or a safe place.
WARNING: The fan and/or downrod should not rotate in the mounting bracket, if installed correctly. Failure to align the slot in the downrod ball with the tab on the mounting bracket may result in fan falling causing serious injury or death.

Slide the Adapter inside the bracket and connect the DC output wire connector mole from the adapter with the wire connector molex from motor through the downrod as shown in Fig Make sure all wires are tucked in the canopy. Connect the input wires of the adapter to the supply wires.

Important: After the connections have been made, the connected wires should be turned upward and pushed carefully up into the outlet box.

Warning: Slide the adapter horizontally into the bracket in the direction of the arrow shown in Fig 9.2 below, and the flat side facing the ceiling.
Note that the upper patterns of the mounting bracket correspond to the two sides of the adapter’s push-in.

Note: DO NOT stand upright (as shown in Fig 9.4) or place the adapter incorrectly ( as shown in Fig 9.5), otherwise the adapter cannot be inserted into the bracket, which will affect the wiring.

Note: The Green/Yellow wire from bracket connects with the supply Ground wire using the wire nut. Connect the White wire of the Adapter to the supply White (Neutral) wire using a wire nut, connect the Black wire of the Adapter to the supply Black (Hot/Live) wire using a wire nut. Then hide them inside the ceiling. (Make sure all the wires are connected to the correct colors as shown in Fig 9.3 )

Raising Canopy:
There are two kinds of canopies and two ways to install. You may receive one of them. Please follow below instructions before installation.

• A: The screws of mounting bracket are exposed. Make sure all wires are tucked in the canopy. Raise the canopy to the mounting bracket, align the hole slots in the canopy with the two mooting bracket screws, then turn the canopy in the direction of the arrow in Fig A until the mounting brackets screws engage from the bigger slots of the canopy to the smaller ones. Then secure the canopy to the mounting bracket with the screws.
• B: The screws of mounting bracket are not exposed. Make sure all wires are tucked in the canopy. Raise the canopy to the mounting bracket, align the two screws into the slot inside the canopy, rotate and twist the canopy to lock into place according to the direction symbol/arrow.

Installing Lampshade:
Align the lampshade slot with the slot of light kit pan, and turn it clockwise to lock it tightly. (See Fig 11.1) The lampshade installed. (See Fig 11.2)

Warning: To prevent SERIOUS INJURY or DEATH, make sure that lampshade is properly secured. Allow the lampshade to cool completely before removing.

Power on
The Fig 12.1 below is a schematic diagram of the whole machine after installation. At this time, the ceiling fan has been installed. Turn on the power supply of the main switch or the room where the ceiling fan is installed. After power on, observe whether the fan light is on.

Remote Control Operating Instructions:
Pairing the Remote Control to Your Fan Within 1 min. of plugging fan to power source, press and hold button for 3 sec. to pair remote control and fan. Successful pairing will trigger the fan lamp off. Remote Control button definitions

• Turns the fan off. OFF

• ( Switches between summer mode and winter mode.

  • Summer mode – (Counter-clockwise) A downward airflow creates a cooling effect.
  • Winter model – (Clockwise) An upward airflow moves warm air away from the ceiling area and redistributes it around the living space.

• Turns the fan on and decreases fan speed.

• Turns the fan on and Increases fan speed.

• Nature Switches the fan speed between nature mode and normal mode. Simulates a natural breeze, gentle enough not to disturb while you sleep.

• Turns the lights on or off and RF pairing.
  Note: Press/hold button for 3 sec. within 1 min. of plugging fan to power source to pair remote and fan. Successful pairing will trigger the fan lamp off.

• Switches between warm light and cool light. WIFI Troubleshooting.
  Note: Press/hold button for 5 sec. The fan will switch to AP Mode, then select AP Mode on APP, follow the APP control instructions and enable fan Wi- Fi.

• Press/Hold button to decrease the light intensity.

• Press/Hold to button to increase the light intensity.
  Warning: Do not expose the remote control to direct contact of water.

APP Control Connection:

1. First download the free Carro Home app from the App Store or Google Play or scan the QR Code as below.
   Note: This ceiling fan needs to use 2.4Ghz wifi to work when you connecting the device, and after connecting it can use the 5Ghz or 2.4Ghz.

2. Open the Carro Home app to create your account. The account with “Carro Home” can be registered through E-mail or Mobile phone.

3. Connect the device to the Carro Home app (Four ways connection):
   Bluetooth connect (WIFI & Bluetooth on) 

4. Press “+” button into the device list, then a window will pop up to show you some devices can be connected.

5. Click “Go to add” (If you click “Do not add” in mistake, please see “Do not add” steps).

6. Choose the device.

7. Connect to your home WIFI, then back to the app and wait for connecting.
   “Do not add” steps:

8. Select “Electrical” (smart switch) or “Air Circulation”(smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.

9. Connect to your home WIFI and tap “Next” to wait for connecting.
   ( Auto Scan (WIFI & Bluetooth on)

10. Press “+” button into the device list.

11. Tap “Auto Scan” on the top.

12. Wait for the device comes out and tap “Next”.

13. Press “+” button to add device.

14. Connect to your home WIFI.

15. Wait for connecting.

WIFI connect-EZ Mode (WIFI on & Bluetooth off) 

• Press “+” button to select “Electrical” (smart switch) or “Air Circulation” (smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.
• Connect to your home WIFI (Only for 2.4Ghz).
• EZ Mode is set as default, just tap “Next” button to wait for the connection to complete.

WIFI connect-AP Mode (WIFI on & Bluetooth off)

• Smart ceiling fan: Press and hold the WIFI button on the remote for 5 seconds into AP Mode. Smart switch: Press and hold the “OFF” button for 10 seconds till the indicator light blinking slowly to into AP Mode.
• Press “+” button to select “Electrical” (smart switch) or “Air Circulation” (smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.
• Connect to your home WIFI (Only for 2.4Ghz).
• Choose AP Mode.
• Press “Next” button to go to connect the fan’s WIFI signal.
• Choose the fan’s WIFI signal “CarroHome-XXXX” then back to the app.
• Wait for connecting.

Connect the device to the Alexa:

• Make sure you have connected the device to the app and working normally.
• Open Alexa app, go to the skill to search “Carro Home” skill.
• Link the skill, log in with your Carro Home app account and password, then authorize and connect with Carro Home app.
• Then the Alexa will find out the device automatically.

Connect the device to the Google Home

• Make sure you have connected the device to the app and working normally.
• Open Google Home app, Set up a device, choose “Works with Google”.
• Search “Carro Home”, log in with your Carro Home app account and password, then authorize and connect with Carro Home app.
• Then the Google Assistant will find out the device automatically.

Connect the device to the Siri shortcuts

• Make sure you have connected the device to the app and working in functional.
• Tap “Smart” on the main menu.
• Tap “+” button.
• Tap “launch Tap To Run”.
• Tap “Run the device”.
• Choose the device you want to control by Siri.
• Select the function you want to control by Siri.
• Then save it.
• Add to Siri, choose the scene you just made, Add to Siri .
• Enter the sentence you want to say to make the device works, Add to Siri.

Basic product parameters

Care and cleaning

1. Check the support connections, brackets, and airfoil attachments twice a year. Make sure they are secure. Because of the fan’s natural movement, some connections may become loose over time. It is not necessary to remove the fan from the ceiling.
2. Clean your fan periodically. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
3. (Optional) Apply a light coat of furniture polish to the wood blades.
4. (Optional) Cover small scratches with a light application of shoe polish.

Do not:

1. Use water when cleaning. Water could damage the motor, or the wood, or possibly cause an electrical shock.
2. Apply oil
   Note: Power

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no is guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Troubleshooting

Try these troubleshooting steps before contacting the Customer Service. For additional operation, maintenance, and troubleshooting information, please contact our customer service center.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>