JETBeam RRT-M1X White Laser Flashlight User Manual

: June 6, 2024
: JETBeam

Table of Contents

Features
Specifications
Battery for Use
Output & Runtime
Operation of flashlight
Protection function
Light Maintenance
Warranty
Service
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RRT – M1X
White laser flashlight

Manual
Thank you for choosing our products
www.jetbeamlight.con

Features

Tactical tail cap switch and rotary head switch for light change, high light transmission lens. suitable for searching, camping, and outdoor activities
Uses 1•WP-72 laser LED
Max 4801M output. max 2300m beam throw
Constant digital printed circuit board design. max runtime 11.5 hours
Battery anti-reverse protection circuits
Filmed mineral scratch-resistant glass
High-strength aerospace aluminum alloy
HAIII hard anodizing finish
IPX-8 water resistance (2-meter submersible)
Impact resistance of 1.5m

Specifications

LED: WP-T2 laser LED
Input: 2.7V.4.2V
Reflector: Lens
Glass: Filmed mineral scratch-resistant glass
Material: HA-Ill military hardiElbOd1200 finish aluminum alloy
Housing: Premium Type III hard-anodized anti. abrasive finish
Battery: 1’21700/1’18650
Switch: Tactical tail cap switch and rotary head switch
Length: 185mm
Head size: 61mm
Body size: 28.3mm
Weight: 360g (exclude battery)

Battery for Use

|

Type

| Nominal voltage|

Compatibility

---|---|---|---
Retharteitge Lithium Battery| 01700| 3.7Y| Yes (recommended)
Retharteitge Lithium Battery| 18650| 3.7| Yes (recommended)

Output & Runtime

FL 1 STANDARD

SOS

---|---|---|---|---|---
| 480LM250LM| 75LM| 1SLM| 300LM| 300LM
| 3min+ 4.4h| 7h| 11. Sh| 9.7h| 8. Sh
| 2300m
| 1322500cd
| 1.5m (Impact Resistance)
| IPX-8 (Underwater 2 meter)

Note
The above data is based on the international flashlight measurement standard ANSI! NEMA, The measurement method described in FL1 is measured in a laboratory using a JETBeam 21700 5100mAh (3.7V) rechargeable lithium battery. Different batteries or use environments may affect the above data.

Operation of flashlight

Insert the battery

Open the tail cover and remove the flashlight and battery from the package.
Insert the battery’s positive pole towards the head of the flashlight (the end where the LED is located).
Tighten the end cap and insert the battery.

Warning

Please put the battery In the direction of the positive pole toward the lamp head, and the battery flashlight will not work if it is reversed
Do not shine light directly on the eyes to avoid damage to the eyes.

ON/OFF

Click the tail switch for ON/OFF.

Brightness and mode adjustment

When the light is turned on, rotate the magnetic ring to change the various brightness modes from Low-Middle-High-Strobe-SOS.

Protection function

The circuit board has temperature protection when over 60°C at the high mode. the brightness output will slow down to 250LM
The circuit board has a time control ability. when over 3 minutes at the high mode, the brightness output will slow down to 2501M.
The circuit board can slow down the brightness output step by step when using a Li-on battery.
The circuit board has a low battery protection function, the power will shut down when the voltage is less than 2.8V

Light Maintenance

Take the battery out for storage if the light will not be used for a long time
Keep the light away from heat, static electricity, and high humidity
Clean the thread and conductive contact of light with a soft cloth. Lubricate the threads every 6 months

Warranty

We provide 60 months(5 years)of the warranty period for this product from the date of purchase in case defects are caused by material or workmanship with normal use. Necessary material and labor costs will be charged after this period

The free warranty does not cover any damages or failure If:

This product is disassembled or modified by anyone other than an authorized JETBeam warranty
This product is damaged by using the wrong battery or incorrect usage.
This product is damaged by defective batteries (such as battery leaks).
Saltwater and corrosive damage to the unit.