YITAHOME BFBPBA-1001 Bidet Attachment for Toilet Seat Instruction Manual

Pure & Easy

ASSEMBLY INSTRUCTIONS
BFBPBA-1001

CONTACT US:

If you have any questions about the installation of YITAHOME® products，just contact us at +1(888)-717-8084 from Mon-Fri 8:00 AM-16:30 PM PST / Saturday 8:00 AM-12:00 PM PST (except holidays) or E-mail us at: after- sale.cs@hotmail.com

Alternative method to contact us(amazon.com orders only)

1. Log into your amazon account
2. Go to “Your Orders” and find the purchase
3. Click on “Contact Seller”

BIDET ATTACHMENT

ASSEMBLY INSTRUCTIONS

Note ：

1. Follow the instructions during installation.
2. Check that you have access to the fill valve under the toilet tank, if not, contact Our Customer Support ASAP.
3. Check that your toilet tank water supply line is flexible, if not, you will need to replace this pipe with a flexible water supply hose.

Function Parts:

*Please Note: illustration will vary depending on the product model.

The extra installation tools you may need:

1. Turn off the toilet water supply valve. Flush to empty the toilet

2. Unscrew the toilet seat to make 2cm gap between the toilet seat and the toilet. Be sure not to completely unscrew the toilet seat.

3. Aim the U-type groove located on the two rotatable mounting discs at two bolts, then push the bidet toward the 2 cm gap.

4. Adjust the bidet nozzle so that it’s placed in the center of the toilet.

5. Screw the toilet again

6. There should be a black rubber washer inserted inside the top of Metal T-adapter. If not, please insert a rubber washer as shown in fig.6.2

7. 1. Firstly turn off the toilet water supply valve Secondly flush the toilet and make sure there is no water in the toilet cistern.
   7.2. Connect the metal T-adapter to the toilet water supply as shown in the fig.7.2

8. Connect the braided stainless steel hose to the Metal T-adapter

9. Connect the braided stainless steel hose to the bidet’s cold water inlet.

10. There should be a black rubber washer inserted inside the top of the plastic T-adapter. If not, please insert a rubber washer as shown in fig.10.2

11. 11.1: Pls. shut down the water supply valve first and then unscrew the basin’s hot water adapter with your hands.
    11.2. Connect the hot water ada. ter (the metal T-ada. ter) to the hot water valve

12. 11.3: Unscrew the thumb nut from the hot water adapter
    11.4: Place the thumb nut on the end of the hot water tube
    11.5: Screw in the thumb nut so that the hot water adapter protects the connecting part.
    11.6: Connect the metal end of the hot water tube to the hot water inlet

Try Your Bidet For The First Time Congratulations, You are ready to use the toilet Bidet for the first time. Be sure to turn the water pressure control knob gently until reaching your desired pressure. The water pressure control device is only to control water pressure, not for setting up the duration of water spray.

The working pressure of this product is 3.5 ± 1.5 Bar

Using Instruction

1. Knob switch to adjust washing mode
   • Switch the knob to “Women” for feminine washing
   • Switch the knob to “Wash” for rear washing
   • Switch the knob to “Nozzle Cleaning” for cleaning the 2 nozzles

2. The chrome-plated lever to adjust water pressure and temperature
   • Lift up or turn down the lever to get gentle pressure or strong pressure
   • Turn the lever to “COLD” for low temperature, “HOT” for higher temperature

Pay Attention
Do not use hot water at when you start to use it. Do not flush the toilet when you use the bidet.

Troubleshooting Tips

Question: There are leaks in the bidet body and hose connections. Answer:

1. Make sure that all threads are properly installed and tightened;
2. Contact us via after-sale.cs@hotmail.com if the problem persists.

Question: The nozzle sprays too far forward.
Answer: Adjust the bidet by pushing it back towards the toilet tank.

Question: After installing the bidet, the toilet seat isn’t flat on the toilet bowl.
Answer:

1. If the extra gap is 1/2″ or less, please install toilet seat bumpers
2. Find a toilet seat that is flat at the bottom without any outer hinge tabs.

Question: The toilet seat bolts do not properly affix to the toilet after bidet installation.
Answer: Install longer toilet seat bolts that accommodate the extra space of the bidet.

Question: How to maintain the nozzle?
Answer: You can clean it once a week with paper towels soaked in vinegar to safely dissolve any hard water.

For additional troubleshooting tips, please contact our customer service or email our after-sale.cs@hotmail.com

Documents / Resources

| YITAHOME BFBPBA-1001 Bidet Attachment for Toilet Seat [pdf] Instruction Manual
BFBPBA-1001, Bidet Attachment for Toilet Seat, BFBPBA-1001 Bidet Attachment for Toilet Seat, Toilet Seat, Seat
---|---

References

• amazon.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>