KREAFUNK aWEAR Bluetooth Headphone User Manual
- June 6, 2024
- KREAFUNK
Table of Contents
KREAFUNK aWEAR Bluetooth Headphone User Manual
SAFETY AND MAINTENANCE INSTRUCTIONS
-
Please read this operation manual carefully before use.
-
The safety and maintenance instructions in this operation manual
should be retained for future reference and must be followed at all times. -
Keep the product away from heat sources such as radiators, heaters or other appliances that produce heat.
-
Do not expose the product to direct sunlight for longer periods. Hig temperatures will shorten the life of the product, destroy the battery and distort certain plastic parts.
-
Do not expose the product to extreme cold as it may damage the internal circuit board.
-
Avoid liquids getting into the product.
-
Do not throw with or stamp on the product. This may damage the internal circuit board.
-
Do not try to disassemble the product. This must only be done by a professional.
-
Do not use concentrated chemical products or detergent to clean the product.
-
Keep the surface away from sharp things, as these may cause damage to the plastic parts.
-
Use 5V / 1A power supplies only. The connection of power supplies with higher voltage may lead to severe damage.
-
Do not arbitrarily discard or place the lithium battery near fire or intense heat in order to avoid a risk of explosion.
If you do experience any problems with your product please contact the retailer you purchased the product from. The retailer will provide you with guidance and if that does not solve the problem the retailer will handle the claim directly with KREAFUNK.
BLUETOOTH® PAIRING
Press and hold the multi-function button for 2 seconds to turn aWEAR on. The LED indicator will light up white and a sound prompt is heard.
When the LED indicator on aWEAR starts flashing white, make sure Bluetooth on your device is turned on. Find the list of visible / connected units on your device and select “aWEAR”. The LED indicator will turn solid white, a sound prompt is heard and aWEAR is ready to play.
MANUAL BLUETOOTH® PAIRING MODE
aWEAR will always re-connect to last connected device, when turned on. If you wish to connect a new device, you can manually activate Bluetooth® pairing mode:
Turn off aWEAR. When aWEAR is off, press and hold the multi-function button for 5 seconds (until a second sound prompt is heard) to activate Bluetooth® pairing mode. The LED indicator will flash white and you can now pair aWEAR with a new device.
MULTI-FUNCTIONS
BATTERY AND CHARGING
CHARGING
Charging time is approximately 2 hours using the included USB cable. The LED indicator turns solid orange when charging. The LED indicator turns solid green when the battery is fully charged.
BATTERY STATUS
When the battery level is below 15%, the LED indicator turns solid red. When the battery level is below 10%, the LED indicator flashes red. aWEAR will automatically switch off when not in use for 60 minutes.
FCC STATEMENT
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference and
- This device must accept any interference received, including interference that may cause undesired operation.
Important
Change or modifications to this product not authorized could void the FCC
compliance and negate your authority to operate the product.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
This product is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU.
The declaration of conformity may be consulted at:
www.kreafunk.com/declaration-of-conformity/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>