Rugged Radios M2RB Mobile Radio User Manual

: June 6, 2024
: rugged radios

Table of Contents

FUNCTION
Getting Familiar
Safety and Overview
overview
Launch and Receive Calls
Emergency Function
Menu Operation
Note: when inputting the radio ID, only numeral mode is available.
Menu Application
Message Function
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

To customers
Thank you very much for using two-way radios.
This product has a newly developed function menu and
humanism operation design, making it easy to use.
It will meet your requirement by the compact size and reasonable price.

FUNCTION

Output power: 55W
dual-band
dual display
dual time slot
1000 channel
1000 contacts
250 Zone
Private call
group call call call in digital mode
Record
1750 Hz| Walkaround
Scan
Encryption
Side-key programmable
Lone worker
Emergency
Monitor
Squelch
VOX
Remote Kill/ Stun/ Activate
Group match/ single Match
---|---

Getting Familiar

Note: Either Long press or short press of side-key1 (P1)/ side-key 2 (P2) /side key 3 (A/B)/ side-key 4 (TXT) can be programmed via software for the following function:

1. None- function
2. All warning tone on/OFF
3. Emergency ON
4. Emergency OFF
5. High/Low Power
6. Monitor
7. One-Touch Access
8. One-Touch Access
9. One-Touch Access
10. One-Touch Access
11. One-Touch Access
12. One-Touch Access| 13. Repeater/ Talk around
14. Scan ON/OFF
15. Tight/ Normal Squelch
16. Privacy ON/OFF
17. VOX ON/OFF
18. Zone Select
19. Lone Work ON/OFF
20. Record ON/OFF
21. Record Playback
22. Delete All record
23. Record replay
24.1750Hz
---|---

This radio has 1000 channels, 1000 contacts, 250 Zone, which can add 64 channels.
Note:The antenna gain is less than 2.15dBi if other antennas are used. The antenna installation height is recommended to be 0.5-5M.

NO	Icon	Function
1	Indicate light	Indicate light will red during transmission
2	PTT	Press the key to transmit

Safety and Overview

SAFETY & RFR
Before using this radio, please read the manual which contains important operating instructions for safe usage, RF Energy Awareness, Control information and operational instructions for compliance with RF Energy Exposure limits in Applicable national and international standards. Also, read the Operational instruction for safe use.

overview

Switch on Press the key for 1 s. the LED indicator lights up, the Screen will show the picture ( which can be designed). Note: If the Tone/Alerts is forbidden, there will not any sound when the power on. Here if need to power off the radio just press the key for 2 s.
Adjust Volume
Clockwise the volume knob to higher the volume or anticlockwise to lower.

Launch and Receive Calls

Zone Selection
The zone is a channel Group. Each radio can set 250 Zone with Max 64 channels.
Menu Function:

press the ENT key/ to enter the menu.
Press the key to choose, after that with ENT/ /to confirm.
The screen shows the chosen zone and name by it.
Move the to choose, after pressing ENT/MENU to confirm.
the screen shows the chosen zone and name by it. ID Selection of Channels, User’s ID, or Group ID

Select the needed Zone ( if there is more than one zone) , using the channel knob to select the channel, user’s name or ID, group name or ID.
Receive and Reply Group Call
The radio must be under a group and then can receive the group call.
When received the group call:

LED indicator on.
on the top of the middle screen will show RSSI mark: The first line will show the group name, income call ID will be in the middle, group call ICON will be the last( only under digital mode)
Hold the microphone and place it between your lip within 2.5-3cm.
Press the [PTT] key to answer the call.
release [PTT] key to receiving the call.
if there is no voice activity, the call end.

Receive and Reply to the single call
Single call means one on one call, only with two types: One is testing the presence of radio before call, and another one is to call immediately.
When receiving one single call:

LED indicator on.
on the top of the middle screen will show RSSI mark: The first line will show the group name, income call ID will be in the middle, group call ICON will be the last ( only under digital mode)
Hold the microphone and place it between your lip within 2.5-3cm.
Press the [PTT] key to answer the call.
release [PTT] key to receiving the call.

Receive all calls
All call means a radio call up all other user’s in a channel to public and important information.
When received one all call:

LED indicator on.
on the top of the middle screen will show RSSI mark: First line will show the group name, income call ID will be in the middle, group call ICON will be the last( only under digital mode)
End of one all call, radio back to receive all call screen, if under the FREE CHANNEL MESSAGE SOUND function, when release the [PTT] key, you will hear a message sound, means the channel is free to use, but can not reply it.

Note: when receiving one all call if you turn over to another channel, the radio stop to receive all calls. During one all-call, you can use any re- programmed key until the call is finished.
Launch a radio call
You can choose a channel, user’s ID or group call with the following method:

channel knob
Pre-programmed key
Contacts
Manual dialing( only for single call)
Using channel knob to make a call

Group call
The radio should be under the group then can have the group call.

Turn over the channel knob, use group name or ID to choose a channel.
Hold the microphone and place it between your lip within 2.5-3cm.
press the [PTT] key to call/. The screen shows group name or ID with Group mark.
release [PTT] key to receiving, when target radio is replying, Screen shows group mark or name or ID5. If there is no any transmitter within the time limit, the call failed.
When radio back to the home screen, you can make a group call with contacts.

Single call

Turn over the channel knob, use the name or user’s ID to choose a channel.
Hold the microphone and place it between your lip within 2.5-3cm.
on the top of the middle screen will show RSSI mark: The first line will show the group name, income call ID will be in the middle, group call ICON will be the last ( only under digital mode).
Release [PTT] key to receiving, when target radio is replying, Screen shows group mark or name or ID
if on the FREE CHANNEL MESSAGE SOUND function, let go [PTT] key, you can hear a message sound( means it channel is free for you to answer) If there is no any transmitter within the time-limited, the call failed.
you will receive a message sound and the screen shows the call finished.
You can make a single call with contacts or use a keypad to search the target radio to make a call.

ALL call
Radio must be programmed with this function so that you can send information to everyone who are under the channel.

Turn over channel knob, use group name or ID to choose a channel.
Hold the microphone and place it between your lip within 2.5-3cm.
press [PTT] key to call/. The screen shows group name or ID with Group mark. Users under the channel can not reply the call.

Use A key to make a group call or single call
Single key call function is convenient for you to set a name or ID for group call or single call with
long press or short press the program key.
Set a name or ID for a key there is more than one single call key

press pre-programmed call key.
Hold the microphone and place it between your lip within 2.5-3cm.
press the [PTT] key to call/. The screen shows group name or ID with Group mark, and the group call/single call ICON.
release [PTT] key to receiving, when target radio is replying, Screen shows group mark or name or ID.
if on the FREE CHANNEL MESSAGE SOUND function, let go [PTT] key, you can hear a message sound( means it channel is free for you to answer). If there is no transmitter within the time limit, the call failed.

Emergency Function

Emergency alarms are only used to transfer emergency situations, you can release an emergency call at any time and anywhere, Even the radio is busy in transmit or receive. MD-9600 support 3 types
Emergency call:

Emergency alarm
Emergency alarm and call
Emergency alarm and voice

Receive emergency call

When receiving an emergency call, a number of emergency calls and alarms are received, exchange the sender name or ID.
with an alarm sound and LED indicator on.
if the radio has activated, they will confirm the emergency alarm automatically. When the radio receives the emergency alarm, the screen shows the emergency alarm warning mark, until send with a confirm message then can log out. While you will not receive any calls and notices from other radio during this situation.

Note: short press cm KEY, then with the pre-programmed off-key, delete all received emergency calls and log out of the emergency mode.
Reply to the emergency call
When received the emergency call:

press any key to stop the emergency call alarm.
Hold the microphone and place it between your lip within 2.5-3cm. if on the FREE CHANNEL MESSAGE SOUND function, let go [PTT] key, you can hear a message sound( means itthe channel is free for you to answer).
press the [PTT] key to have a call, radio under the emergency call mode.
release [PTT] key, when replying the emergency call, the screen shows group mark or ID and call ID
After the call, short press I’m key, then press a pre-programmed emergency key to off, delete all the emergency calls, and log out.
Radio back to the home screen.

Emergency Alarm
This function is called not- speech signal and allows to send an emergency alarm and will trigger on another radio.

press pre-programmed power on key.
the screen shows sending emergency calls, exchanging ID with other radio. The emergency call mark will show on the home screen.
When receiving the emergency call, the radio issues the emergency call and the screen shows the emergency call send out successfully. If the radio does not receive any confirmation with the emergency call and out of the sending times, the radio will with a message sound and screen shows the emergency call failed.
radio logs out the emergency mode and back to the home screen, If the radio is under silence mode, there will not be any sounds or reminders during the emergency mode.

Emergency Alarm call
This function allows you to send an emergency call to other radio, after being confirmed by the radio, the two radios can contact by a pre-programmed channel.

press pre-programmed power on key.
the screen shows sending emergency calls, exchanging ID with other radio. The emergency call mark will show on the home screen.
When receiving the emergency call, the radio issues the emergency call, and the screen shows the emergency call has been received.
Hold the microphone and place it between your lip within 2.5-3cm.
Press the [PTT] key for a call, then the screen will show group ICON.
release [PTT] for receiving.
if on the FREE CHANNEL MESSAGE SOUND function, let go [PTT] key, you can hear a message sound( means it channel is free for you to answer), press the [PTT] to answer the call or press pre-programmed emergency call to off and logout the mode.
radio back to the home screen, If the radio is under the silence mode, there are not any sounds or notices during the emergency mode, not receive calls from target radio, until press the PTT key.
If the radio is under WITH VOICE MUTE mode, there are not any sounds or notices during the emergency mode, not receive calls from the target radio, Until press the PTT key to call or receive, then the screen will show up.

Voice emergency Alarm
This function allows you to send an emergency call to others, after confirmation, the microphone of the radio will activate, allowing you to call other radios without pressing the [PTT] Key. If press the [PTT] key during this mode, the radio will ignore [PTT] and stay on emergency mode.

Note: if you press the [PTT] key during this time, hold the key before duration within limits, release the [PTT] key to transmit.

press the pre-programmed emergency start key.
The screen shows sending an emergency alarm, LED will show the emergency call, Mark.
The screen will show an emergency call successfully; you can talk to the microphone clearly. When this function is on, the radio will transmit automatically without pressing the [PTT] Key before duration within limits.
During transmission, LED will show the Emergency alarm mark.
When the Emergency microphone ends, the radio will stop transmitting, press [PTT] key to transmit again, If the radio is under Silence mode, there is no any sound or notices.

Restart Emergency Mode
The radio will restart emergency model when meeting the following situation:

It will log out the emergency mode when the radio changes the channel under the emergency
mode. If activate the emergency alarm is in the new channel, the radio will start Emergency mode.
Under Emergency call/ transmit, press the pre-programmed emergency key. It will log out the emergency and restart the emergency alarm.

Logout Emergency mode
The radio will logout emergency mode when any of the following situations happens:

confirm with the received emergency call or
Meet with the max emergency call or
Press the pre-programmed emergency off-key or
press [PTT] key

Note: if turn off the radio, the emergency mode will be logout. Then the radio will not be under emergency mode when the radio on again.

Character Input
You can use the 3×4 alphanumeric keypad in the microphone to input the character/ The radio contains two modes:

English letter
Numeral input mode

Note: when inputting the radio ID, only numeral mode is available.

Numeral input:

Under Numeral input mode, press the keypad to get the desired number, press can show press # to switch the input mode.

press to enter Menu, then press to choose the desired menu.
press choose one function or enter a sub-menu.
press ESC to return the higher level menu.

Note: after a period of time not activity radio will automatically exit and return to the main menu screen ( hang time can be set by the programming software).
Radio check( ONL V digital mode)
If there is any activation, this feature allows you to determine whether there is other radioactive inside the system, and does not disturb the users, none- voice or visual notice appears on the target radio/ Send radio check
Using Menu:

press to enter Menu.
press to button to select contacts, then press to select.
Move to the required user alias or ID, then press to select.( only in single call mode)
Or press to manual dialing, and then press to select.( only in single call mode)
If there are before calling ID, show ID and along with flashing cursor, using the keypad editing ID, press .
Press to radio detection, then press to select.
When the screen displays radio detection: User Alias or ID, it is an indication of the ongoing radio detection.
waiting for confirmation.
If the target radio is active in the system, then it makes a prompt sound, the screen will show that the target radio has responded shortly7.
Or if the target radio in the system is not active, then it makes a prompt sound, the screen will show that target radio No available shortly.
Radio returns to user alias or ID screen, If you press when waiting for de confirmation, made a prompt sound, the radio will end all retry and exit detection mode.

Monitor
Using the Monitor function to open the microphone of the target radio (only the user’s alias or ID), You can use the function to monitor any sound around the target radio.
The radio should be set to allow the use of this function via the programming software.
Start Monitor
Using Menu:

press to enter Menu.
press to button to select contacts, then press to select.
Move to the required user alias or ID, then press I to select.
Or press to manual dialing, and then press to select.
If there are before calling ID, show ID and along with flashing cursor, using the keypad editing ID, press
press to choose Monitor, then press to select.
Radio will make a prompt sound
waiting for confirmation Screen show Monitor successes or failures.

Contact setting
Contacts is an Address book, in which, each entry corresponds to an alias or ID used to start the call.
In addition, each item, according to the different content setting, relates to three types of calls: group calls, single calls, all calls. Your radio supports a digital address book, The contacts entries display in the followings information:

Contacts
New contact
Manual dial

Group call with Contacts

press to enter Menu.
press3 to button to select contacts, then press to select, entries arrange in alphabetical order.
Move to the required user alias or ID, then press into select.
Hold the microphone and place it between your lip within 2.5-3cm.
press [PTT] to start calling, the screen displays the calling alias or ID, as well as the ICON of the group call.
release [PTT] to receive, when any user responds within the group, you will see the call icon of ID on the screen.
if you enable the CHANNEL FREE PROMPT function, when the target radio release the [PTT] button, you will hear a short beep, said this channel is idle, waiting for your answer, Press the [PTT] to answer. If in a pre-programmed group called hang time without voice activity, the call is ended.

A single call with Contacts

press enter Menu.
Press [( or (2] to button to select contacts, then press to select, entries arrange in alphabetical order.
Move to the required user alias or ID, then press to select.
Hold the microphone and place it between your lip within 2.5-3cm.
press [PTT] to start calling, The first line will show Alias or ID, the second line will show Single call ICON.
Release [PTT] to receive, when any user responds, the screen will show the ID.
if you enable the CHANNEL FREE PROMPT function, when the target radio release the [PTT] button, you will hear a short beep, said this channel is idle, waiting for your answer, Press the [PTT] to answer. If in a pre-programmed group called hang time without voice activity, the call is ended.
You will hear a sound shortly, the screen will show the call ended.

Call Log
Your radio can record all the recent dialed, received, and not answered call. Use the calling record function view and manage the recent calls.
Checking New Call’s Number
Menu items can show the not-answer calls, received calls, and dialed calls.

Press the key to enter the menu mode.
Move the key to the Call Log, and then press the key to choose.
Move to the required list, and then press the key to choose.
The screen on the top of the list shows the recent entries.
Press [or]check list, press (PTT) at the current selected aliases or ID to start a call.

Miss Call
Whenever you miss a call, two-way radio will display a not answered call, select view or view later.
Note:
If you press (PTT), when you’re viewing a missing call number, radios will exit the missing call screen and establish a single call again.

The screen shows the missing call, and the missing call’s number and view.
Press view missing call’s ID, missing call’s record list displayed on the screen.

Press to store or delete this entry; Or move key to view later, and then press key choice, return to the main screen.
Storing Missed Call’s Alias Or ID

Press the key to enter the Menu.
Move the key to Call Log, and then press the key to choose.
Move the ey to a missed call, and then press the key to choose.
Move key to missed call’s alias or ID, and then press key to choose
Move the key to the store, and then press key to choose
Radio Shows flashing cursor, if needed, enter the ID alias, and then press [ B] ey.
The screen contacts have been saved.

You can also enter ID without an alias.
Deleting Calling Log’s Record

Press the [CD] key to enter the Menu.
Move the key to Call Log and then press the key to choose.
Move the key to a missed call, and then press the key to choose.
Move key to missed call’s alias or ID, and then press key to choose
Move key to delete the entries, then press key to select if you need to delete this entry.
Select “yes”, then press the key to delete the entries, screen appears entry deleted; Or select “no”, press key to return to the previous screen.

When you select a call list but there is no entry in, the screen will display the list is empty, if the keyboard is open at this time, will be a low tone hint sound.
Call Alert Operation
Call alert makes you can suggest specific radio users in the possible time to call you back.
This feature applies only to the user alias or ID and can be used through the menu by address book or manual dialing.
Receiving And Checking Call Alert
When you receive a call alert, the screen shows a call promptly, alternating transmit radio’s alias or ID

YOU will hear the sound of a repeat, LED light turn and shine red.
Then press and release [PTT] to confirm the prompt, or press to select “neglect” to exit the call reminder.

Starting Call Alert From Contact List

Press the key to enter the Menu.
Move the key to Contacts, and then press the key to choose.
Move key to missed call’s alias or ID, and then press key to choose Or move key to manual dialing, and then press key to choose, a flashing cursor appears, then enter the user ID you want to call, and then press [Bl key.
Move key to Call Alert, the screen display Call Alert:< user s alias or ID >, and then press [Bl key and instructions have been sent Call Alert.
When the radio sends a call alert, the LED indicator for the red light.
If you receive calls prompt confirmation, issued a prompt, and display the call alert-success.
Or prompt confirmation if not received a call, send a hint sound and the screen call fails.

Message Function

Your radio can receive the message or send the message.
Edit and send Message
Using the Menu:

press to enter Menu.
press to button to select MESSAGE, press to enter.
press to button to write MESSAGE, press to enter.
A flashing cursor appears, using the keypad to input message, press.,to move to the left one, pres to the right one, when editing area has content, press ESC To delete any useless character, otherwise when editing area without content to return to the higher level menu.
after writing the message, press to choose to send or save.
when in the process of editing, the user can choose by pressing the key to the empty option to empty all the content of the editor, quickly return to the higher level menu.

Send Quick Text
Two-way radio supports a maximum of 50 programming of prefabricated text messages by the agent:
When a predefined text message, you can edit every message before you can send each message.
Using the Menu

Press the key to enter the Menu.
Move the key to Messages, and then press the key to choose.
Move key to Quick Text, press key to choose
Move key to the required quick text, press key to choose
A flashing cursor appears, using the keyboard to input messages, press [] key to move to the left one, press[m]button to the right one, when editing area have content,press the [C3] key to delete any useless character, otherwise when editing area without con tent to return to the higher level menu.
After writing the text message, press to choose to send or save.
If the messages sent successfully, issued a prompt sound, and the screen displays a text message has been sent. Or if the message was not sent, issued a high tone hint sound, and screen displays text message sent failure. If a message sent fails, the radio will return to the chance to return to the retransmission selection screen.
After Choose send move to the alias or ID, and then press key to choose. Or move key to manual dialing, and then press key choice. Enter the user alias or ID, then Press
The screen shows the message: < user/group name or ID> call, text messages were being sent to confirm.
If the messages are sent successfully, issued a prompt sound, and screen display text message has been sent. Or if the message can’t send, send out a high tone hint sound, sc reen display message sent failure, failure if the SMS messages, intercom chance to return to the retransmission selection screen.

Send Quick Text With A Key

Press Preprogrammed, single bond claims to a predefined alias or ID sends prefabricated text messages.
The screen displays a text message: < user/group name or ID> call, to confirm text me messages were being sent
If the messages are sent successfully, issued a prompt sound, and the screen displays a text message that has been sent.
Or if you cannot send text messages, screen display text message sent failure. If a message is sent fails, the intercom chance to return to the retransmission selection screen.

Manage The Failed SMS
In the retransmission selection screen, you can choose the following options:

Resend,
Forward,
Edit

Resending Message

Press to resend the same message to the same user/group name or ID.
If the messages are sent successfully issued a prompt sound and display messages sent or if you cannot send text messages, screen display text message sent failure.

Forwarding message
Choose to forward the message to another user/group name or ID.

Move the key to forward, and then press the key to choose.
Move to the alias name or ID, and then press key to choose.
Or move key to manual dialing, and then press the button to choose, enter your user ID, and press key.
The screen displays a text message: < user/group name or ID> call, to confirm text mes sages were being sent
If the messages are sent successfully, issued a prompt sound, and the screen display a text message has been sent.
Or if the message was not sent, issued a high tone hint sound, and screen displays text message sent failure.

Editing Message
Choosing edit to edit the message before you edit.
Note: if you have a subject line (receive text messages from email program), you can’t edit
the subject line.

Move key to edit, then press key to choose
A flashing cursor appears, using the keyboard to input messages, press [] key to move to the left one, press [a] button to the right one when editing area has content,
press the [cm] key to delete any useless character, otherwise when editing area without content to return to the higher level menu.
After writing the text, press choose to send or save
When in the process of editing, can choose by pressing the [mm] key to empty option to empty all the content of the editor, quickly return to the higher level menu
Choose after button to send the required alias or ID, and then press key to choose
Or move key to manual dialing, and then press the button, enter your user ID and press key
The screen displays message:< user/group name or ID> call, to confirm text messages were being sent
If the messages are sent successfully, issued a prompt sound, and the screen display a text message has been sent.
Or if the message was not sent, issued a high tone hint sound, and screen displays text message sent failure.

Manage The Sent Sms
Once a message is sent to another radio, it will be saved in the “sent items”. Send after sending a text message has always been to “sent items” at the top of the list. The sent items folder can store up to 50 recently send text messages. After the folder is full, the next send text messages will automatically replace the earlier messages in this folder.
Note: at any time pressing the key can return to the previous screen.
Chack The Sent Messages
Using the menu function:

Press button to enter the Menu.
Move the key to Messages, and then press key to choose
Move to sent items, and then press key to choose
Move the key to the SMS, and then press key to choose. If the message from the email program, subject lines, will appear in the top right corner of the screen icon indicates the state of SMS.

Sending the sent messages
When the view sent messages, you can choose the following options:

Resend
Forward,
Edit
Delete

Check the message, press [CD] key again
Move the key to resend, then press key to choose.
The screen displays: < user/group name or ID > call, confirm that it is preparing to send the same message to the same target radio
If the messages are sent successfully, issued a prompt sound, and the screen display text message has been sent.
Or if the message was not sent, issued a high tone hint sound, and screen displays text message sent failure. If a message sent fails, the intercom chance to return to the retransmis sion options screen. Press the key to send SMS weight to the same user/group name or ID.

Note: Except for Pressing the , key, if you change the volume and press any other key, will return to this message. When you press [PTT] for a single call or group call, or as a response to the group calls, the radio will exit the retransmission selection screen. If received text messages or remote sensing information, emergency call, or call the police, or call reminder, the radio will exit the retransmission selection screen. If you press [PTT]in response to a single call (in addition to the radio in the show did not answer the call screen), or at the end of all calls, the screen will return to resend selection screen. Press key, enter the forwarding, edit, or delete selection screen.

choose forward, will choose the SMS sent to speak to other groups/user alias or ID.
choose to edit, to edit the selected text messages before sending
choose delete, delete the selected text.

Note: if you screen out SMS messages when sending text messages, so radios will be in the “sent items” folder for SMS status updates, not the tip or by a voice prompt. If the messages in the sent items folder state before the update, walkie-talkie pattern changed or blackout, walkie-talkie will not be able to complete the ongoing message processing, and automatically start tag to the icon of failure. This radio can handle 5 text messages at the same time. At this stage, the radio can’t send a new message, and automatically start the tag icon to send failure.

Deleting all Sent Messages In the “Sent ltems”
Using the Menu Function

Press the button to enter the Menu.
Move the key to Messages, and then press ] key choice.
Move to Sent Items, and then press key choice.
Move the key to delete all, and then press key choice.
When it appears to delete messages, press button, select “yes” project has clear scredisplay has been sent.
Or delete the text, move to no, and click key to return to the previous screen.

When you select the “sent items” but not one of the text messages, the screen will display thlist is empty, if the keyboard is open at this time, will be a low tone hint sound.
Receive SMS
When your radio is receiving SMS, the left of the screen shows the sender alias or ID ICONS and text messages.
When receiving text messages, you can choose the following options:

reading?
Reading Later
delete

Note: when the radio shows tip on the screen, please press (PTT), two ways will exit to establish a single call or text message screen group call.
Check the SMS

Move the key to Read, And then press key to choose
the selected text messages on the inbox opened, if the message is from the email program, it will appear a subject line.
Click the key to return to your inbox. Or press to reply, forward or delete messages.

Move key to enter later view or delete selection screen:
Later, select the view screen before returning to receive messages.
Choose delete, delete receive text messages.
Manage Received SMS
Use your inbox to manage messages. inbox can store up to 50 text messages at Most.
Two-way radio supports the following text options:

Reply
Forward
delete
Delete all store the message in the inbox in the order of received time.

Note: at any time according to the Black key can return to the previous screen.
Check The inbox SMS

Press the button to enter the Menu.
Move the key to Messages, and then press key to choose
Move to the inbox, and then press key to choose.
Move the key to check the message. If the messages are from the email program, it will appear a subject line.
Press the key to choose the current text, then press **** key again to reply, delete, or forward this message.

Reply The inbox SMS
Use the menu function:

Press button to enter the Menu.
Move the key to message, and then press key to choose
Move to the inbox, and then press key to choose
Move the key to the SMS, and then press key to choose. If the messages are from the email program, it will appear a subject line.
Press again button to enter the submenu.
Move to reply, and then press the key to choose.
Move to write messages, and then press key choice, a flashing cursor, using a keyboard editing text messages.
Or move key to prefabricated text messages, and then press key to choose.
Choose the required message after press a flashing cursor, if needed, with the keyboard editing your message.
After Writing the text, press
The screen displays the message:< user/ call group name or ID>, to confirm. text messages were being sent
If the messages are sent successfully, issued a prompt sound, and screen display text message has been sent.
Or if you cannot send text messages, screen display text message sent failure. If the message sent fails, the radio returns to the retransmission selection screen.

Deleting the inbox messages
Use the menu function:

Press the button to enter the Menu.
Move the key to message, and then press key to choose
Move to the inbox, and then press key to choose
Move the key to the SMS, and then press key choice. If the messages are from the email program, it will appaer a subject line.
Press again button to enter the submenu.
Move the key to delete, and then pres key to choose.
Delete messages, move key to “yes”, then press key to choose.
The screen appears the short message has been deleted.
The screen back to the inbox.

Deleting all messages in the inbox
Use the menu function:

Press the [CD] button to enter the Menu.
Move the to the Message, and then press key to choose.
Move to the inbox, and then press key to choose.
Move the key to delete all, and then press key to choose.
When it appears Deleting the messages, move select yes, and then press key to choose
Then The screen inbox was empty already.

When you select the “inbox” but not one of the text messages, the screen will display the list is empty, if the keyboard is open at this time, will be a low tone hint sound.
Encryption
If you enable this feature, which is beneficial to prevent other users on the channel by using the method of software encryption for unauthorized eavesdropping. The launch of signaling and user identification part unencrypted. Your radio must be enabled on the channel encryption function, can send encrypted, even if the receiving transmission is not must request to do so.
Basic encryption
Two-way radio can only be assigned more than one type of encryption. If users Call for encryption or decryption of data transmission, must make to be preprogrammed walkie-talkies, and the launch radio has the same “encryption keys” (suitable for basic encryption). If your radio receives different encryption keys or key values and key encryption call ID, you will hear the sound of the transport chaos encryption (basic). Press the preliminary programming encryption keys on or off.
DTMF
Dual Tone Multi-Frequency (DTMF) function allows operating radio when there is interference in the radio system. To initiate a DTMF call

Press and hold [PTT] key.
Enter the number you need.
You can disable the DTMF tone by turning off all radio tones and prompts.

Secrecy
You can activate or kill any radio in the system. For example, you might want to disable a stolen radio, to prevent thieves use it, and enabling it when you get it back.
Note: radio kill or activation is limited to activating the radios with these functions.
Radio Disable
Use menu mode

Press key to enter the menu mode.
Move key to Contacts, and then press key to select, entries are in alphabetical order.
Move key to the required alias or ID, and press key to select.
Or move key to Manual Dial, then press twice key to enter a user alias or ID, and press key to select.
Move key to radio disable, and then press key to select.
The display shows the radio disable: and the LED indicator light is red.
Wait for confirmation.
If successful, emit a beep and the screen displays radio disable successfully.
Or if it fails, emit a beep and the screen displays radio fail to disable.
During radio disable operation, do not press the key, because you will not get a confirmation message.

Scanning List
Create a scan list and assign to a single channel / talkgroup, your radio can support up to 250 scan lists, each up to 16 members. Each scan list support mixed analog and digital channels. You can edit the scan list to add I delete channels or set the priority channel.
Check members of list

Use the channel knob to select a channel with a pre-programmed scan list;
Press the [CD] key to enter the menu mode;
Move key to scan, and then press the key to select;
Move key to View list the list, and then press the button to select;
Use key to see members of list.

If you set the priority, the priority icon is displayed on the left of the member alias, indicating that the member is the Priority 1 or Priority 2 channel; if the priority is set n. no priority icon.
In a scan list, you can not have more than one Priority 1 or Priority2 channel.

Scanning Instruction
When scanning, your radio can view if there is a voice activity in the current channel through circulating a pre-programmed scan list. LED lights flash for a red light, and the scan icon appears on the screen.
When scanning in dual-mode, if you’re in a digital channel and your radio locking an analog channel, the radio will switch automatically from digital mode to analog mode throughout the duration of the call. And vice versa.