SMPLEBP True Wireless Earbuds User Guide

True Wireless Earbuds

Welcome

I thank you for purchasing smpl. Earbuds. This user manual contains instructions for setting up your new Earbuds with ease, so please read our guide carefully, and keep it for future reference.

Accessories

Bluetooth Pairing

1.  Auto-connecting the earbuds switch on and connect to each other automatically when taken out of the charging case. And the earbuds will flash blue lights to indicate that the earbuds are automatically pairing to each other. Once paired successfully, one left earbuctswill alternately flash the red light and blue light, and the right will finch blue light.

2. Connecting to Bluetooth device Turn on the phone’s Bluetooth function and select° sm pl. earbud-p ” in your Bluetooth list.

Note:

1.  To manually switch on, touch the multi-function button on both earbuds for 1.5 secs.
2. if the earbuds have not successfully connected to Bluetooth for more than 5 minutes, they will automatically shut down.
3. The earbuds switch off automatically when placed back in the charging case.
4. Do not leave the left and right earbuds too far when you take out them from the charging case for pairing. The recommended distance is no more than 15 CM.

Touch Button Controls

Rotate/adjust the earbuds with more than one finger to avoid causing unexpected operation

LED Indicator

Voice Prompt

Turn on the earbuds: “Power on”| Successfully paired to the device: “Connected”
---|---
Turn on the earbuds: “Power off”| Battery level low “Battery low”
Paired to each earbud: “Pairing”| Unpaired: “Disconnected”

Replace Ear-tip

Note: Please try out the different size ear tips to find the most comfortable fit for you!

FITTING

1. Insert the earbuds into your ear canal.
2. Feel free to rotate/adjust your earbuds for the most comfortable fit.

CORRECT

INCORRECT

Single-earbud Mode

Removing the right or left earbud from the charging case, it will automatically turn on, and select Left earbud or right earbud in the Bluetooth list to connect the left or right earbud.

Resetting of earbuds

Keep your earbuds in the charging case, and keep the charging case plugged in. You can clear your earbuds’ Bluetooth memory by pressing and holding the multi-function button for 8 seconds.

The left and right earbud’s Bluetooth memories may need to be cleared individually if you have used the earbuds in Single Earbud Mode.

Note: The earbuds are powered on & off individually.

Problem

Charging case

Connect the charging case to the computer or USB 5V output device.

Specifications

Bluetooth version: V5.0
Input: DC 5V, IA
Charging time: earbuds ≤ 2 Hours, charging case ≤ 4 Hours
Playtime: Up to 5 Hours + 15 Hours
Standby time: 120 Hours
Earbud battery: 2 x 55mAh
Charging case battery: 3.7V, 500rnAh
Driver (full range): 6mm x 2
Bluetooth Range 10m / 33ft
Audio code SBC, AAC
Support protocols: A2DP, AVRCP, HFP, SPP

Warning

Fully dry off the earbuds before putting in the charging case to avoid any damage to the case. The earbuds are sweat/water resistant but the charging case is not.

Cautions

1. Avoid extreme heat, cold, and humidity.
2. Avoid dropping or crushing the earbuds, stressing the cable by rapid pulling or extreme force, or bending the cable at s sharp angle
3. Wax may build up in the earbud tips, lowering the sound quality. Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
4. If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
5. If you experience regular discomfort while using this product, discontinue use and consult the physician.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, If not installed and used In accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user Is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Happy?

We’re glad to hear it!
Please tell your friends& Share your experience on Amazon by writing a review.

Questions or Issues?

Our customer support team would love to help!
Please contact us at hello@ gets. pl
We ‘re here M-F From 9 am-5 pm PST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>