Kuaimen CL-V17 LED Fill Light User Manual

Kuaimen CL-V17 LED Fill Light

Product Information

Specifications

• Model: CL-V17
• Colour: N/A
• LED Qty: 92pcs
• Color Temperature: 2500K, 5500K, 9000K
• luminance: 900 lux at 0.3m, 1100 lux at 0.5m, 1000 lux at 900m
• CRI: 95
• Battery: 3.7V 3000mAh
• Power Input: 4W
• Charging: 18WPD/QC Type-C
• Wireless Charging Output: N/A
• Size: 62*85mm
• Weight: 100g

Product Usage Instructions

Function and Display
ON/OFF: Turn the power button on/off. Switch to F to turn on the front lights and B to turn on the rear lights.

Parameter Settings: Press the +/- buttons to switch modes and adjust brightness for both front and rear lights. Various modes are available including white light, colorful lights, and special effects.

Charge & Wireless Charging Function
Charge: Use Type-C for charging. Four lights remaining on indicate that charging is complete.

FAQ

1. Q: Is the fill light waterproof?
   A: No, the fill light does not have waterproof or dustproof functions.

2. Q: How often should I charge the battery to extend its service life?
   A: It is recommended to charge and maintain the battery every three months to extend its service life.

Preface

Thank you for purchasing our products!
This is an ultra-thin magnetic fill light that supports front and rear camera fill, and also comes with wireless charging function. Supports BI color and RGB function.

Please read this manual carefully before use, and keep it for future reference after reading.

Matters needing attention

1. This fill light does not have waterproof and dustproof functions.
2. Do not let this fill light be strongly impacted.
3. Do not look directly at the light-emitting surface of the fill lamp in use for a long time in a close range, or it may damage your vision.
4. After charging, unplug the power cord. fully charged before using this product again, otherwise it
5. After not using this product for a long time, the battery should be may lead to no power and unable to start.
6. In order to extend the service life of the battery, it is recommended to charge and maintain it every three months.
7.  This product has a built-in rechargeable lithium batter will be reduced, which is a normal phenomenon.

Product introduction

1. Front luminous surface
2. Front luminous surface
3. Function buttons
4. MagSafe
5. Indicator light
6. Wireless charging
7. Rear luminous surface
8. Switch button
9. Type-c charging port

Product installation

• Attach to the phone through a magnet
• Phone that does not support magsafe function,
• The included iron sheet accessories need to be installed first.
• Supports front and back bidirectional supplementary lighting.

Function and display

ON/OFF
Turn the power button on/off. The middle gear is turned off Switch to “F” to turn on the front lights and “B” to turn on the rear lights.

Parameter settings

Front lights

Press the “△” and “▽” buttons to switch modes (loop switching)
Press the “+” and “-” buttons to adjust the brightness

Headlight modes: 12 modes in 3 categories

1. White light:All white lights are on/ and the white light in the middle i the white lights around are on/s on
2. Colorful lights: red/yellow/green/Cyan/blue/ purple
3. Special effects: white flashing light/ white breathing light/

RGB color tone loop

Rear lights
Press the “△” and “▽” buttons to switch colors (5 levels )
Press the “+” and “-” buttons to adjust the brightness (10 levels )

Wireless charging function

Open
In the shutdown state, long press the right button to turn on the wireless charging function.At this point, the first indicator light changes from green to red.

Close
The wireless charging function will automatically turn off after 20 seconds of deactivation and needs to be restarted for next

Specifications

The specifications and parameters of this product are tested in accordance with the company’s laboratory samples. The finished product may have some differences, which will not affect the normal use; if the design and specifications changed will not prior notice.

FCC Statement

Warning
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure compliance statement
This device has been evaluated to meet the general RF exposure requirement

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>