UNIVERSAL ELECTRONICS R34010 Comcast Platco TV Remote User Guide

UNIVERSAL ELECTRONICS R34010 Comcast Platco

CMF v2

1. IR Lens
   Color: Black
   Material: Polycarbonate
   Finish: Glossy

2. Housing
   Color: Black
   Material: ABS
   Texture: VOi 3400 / 21-24
   (ref. SKY’s EC202)

3. Rubber Buttons
   Color: Black, top-printed icons
   (ref. Artwork v1)
   Material: Rubber
   Finish: Smooth

4. Hard Cap Keys
   Color: Black, top-printed icons
   Material: ABS
   Texture: VOi 3400 / 21-24
   (ref. SKY’s EC202)

5. Home and Voice Keys
   Color: Clear, back-printed icons
   (ref. Artwork v1)
   Material: PMMA
   Finish: Polished

6. App Buttons A
   Color: Black, 2.
   top-printed logo
   (ref. Artwork v2)
   Material: Rubber 3.
   Finish: Smooth

7. App Button B
   Color: Black,
   top-printed logo
   (ref. Artwork v2) 4.
   Material: Rubber
   Finish: Smooth

8. App Button C
   Color: Black,
   top-printed logo
   (ref. Artwork v2)
   Material: Rubber
   Finish: Smooth

9. App Button D
   Color: Black, 4.
   top-printed logo
   (ref. Artwork v2)
   Material: Rubber
   Finish: Smooth

QuickSet

This product shall support the following features:

• Auto Setup
• Manual Setup
• Optimized Setup Maps (OSM)
  The following are descriptions of the Quickset features:
  Auto Setup: Quickset allows for auto setup of the RCU by identifying devices connected through the HDMI network. The RCU is programmed automatically over the RF link.
  Manual Setup: Quickset allows for manual selection of a Brand for programming of devices without
  having to go through Auto Detection and Programming. The RCU is programmed automatically over the RF link.
  Optimized Setup Maps: OSM assists the user with a UI flow to program a TV or Audio device in the RCU. After the user selects brand through the UI, the RCU software and Quickset allows for the testing of functions and by the user. The RCU is programmed over the RF link after the appropriate feedback is observed by the user.

Pairing

• Press and hold DIGIT 1 + DIGIT 3 for 1 second
• Continuous GREEN led blink until paired or timed out

LED Feedback

• Pairing
  • GREEN led blink every 250ms for duration of advertising (10 seconds)
• Key Press
  • RED if not BLE bonded
  • GREEN if BLE bond
• Factory Reset
  • 4 RED blinks before reboot
• Unbind BLE
  • 4 blinks if successful
  • 2 blinks if unsuccessful

Features:

• UE878NMEH (512K Flash/64K RAM)
• BLE
• Voice with single digital MEMs microphone
• QS Cloud
  •  Same cloud Comcast accesses today, and implemented by Comcast
• Tri‐color (RGB) feedback LED for user feedback
  • Same tri‐color LED used in XR15 and XR16 remotes
  •  Charge pump circuit to support blue color
• Option in battery compartment for 10 pin tag connection and 10 pin header
• •  Follow latest Sky EC302 design
• Buzzer/Piezo for Remote Finder feature (OWMB‐9045HS‐27‐16) – optional install
• SMT IR diode (Paralight L‐S15CAIR1C‐HD/ Bright LED Electronics Corp. BIR‐HMC33M‐2‐TRCA‐UEI)
• PCB: Double Sided, CEM‐1, Carbon Thru Hole, Wet Film
• Rubber keypad with carbon ink
• ABS plastic housing
• PC IR lens
• PMMA back printed crystal keys
  •  MIC
  •  HOME
•  ABS key cap – OK key
•  ABS key caps
• Metal domes – all 30 keys
• 2 AAA batteries operation – designed for alkaline
• Operating Temperature
  o 0°C to +50°C

Customer Marking Label

COMPLIANCE WITH FCC RULES AND REGULATIONS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase or decrease the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced remote control/ TV technician for help.

This equipment has been verified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.

FCC Authorization Label
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Canada:
This device complies with RSS‐210 of the Industry Canada Rules: Operation is subject to the following two conditions:

1. This deice may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>