addlon TSZ7FST19LD Smart LED Bulb User Manual

: June 9, 2024
: addlon

Table of Contents

Installation Step
Troubleshooting ways
FCC Warning Statement
Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

addlon TSZ7FST19LD Smart LED Bulb User Manual

WARNING

Not for emergency lighting
Risk of electric shock
Risk of fire
Risk of burns
Do not use where directly exposed to ater
Not for use in totally enclosed luminaries
Do not use with medi and life-suppo instments

Do NOT USE WITH STANDARD D IMMERS

Installation Step

Follow the available instructions and resources to set up your smart device.

Step 1: Download the app

Download the Join in Home APP from App Store or Google Play.
Symbols

Scan the QR code to download

Step 2: Set up account

Create an account in Joinin Home App.

Step 3: Install the smart device

Screw the smart bulb into a standard indoor light fixture
Power switch for the lamp or light fixture must be ON

Step 4: Light Pairing mode

Remove power to bulb ( turn of light switch) fo川sec., add power for 1 sec.(turn on light switch)
Cycle five times. Bulb will be in ON position and begins flashing quickly.

Step 5: Add Device

Click Add Device of the+ at the upper right corner.
. System will auto scan the smart device.
Make sure your wifi is 2.4G.
Done. Enjoy you time with APP control

Voice Control

Compatible with Amazon Alexa and Google Assistant

Follow the steps in the Amazon Alexa or Google Home app to connect the Joinin Home app or select “Third-Pa Voice Se vices” in the Join in Home app.
Voice Control

Product Parameter

Rated voltage: 120V AC
Frequency: 60Hz
Rated power: 7W (60W Equivalent)
Color Temperature: 2700K
Lu minous Flux: 800LM
CRI: 80
Rated Life: 15000H
socket Type: E26
Working Temperature: 20℃－40＇℃

Troubleshooting ways

Cannot connect to your wi－if network.

Please make sure your Wi-Fi router is unde the 2.4GHz se忧ing and the entered router passwo时is correct.
lf Wi-Fi signal is too weak, reset your Wi-Fi router and t『y again.
Please enable the Joinin Home App to get your local location and Bluetooth.

Setup is not working properly

clean all apps that a陀running in the background then reopen the Joinin Home App.
Uninstall and 『·einstall the Join in Home App then repeat the setup process.

The bulb is not responding to Joinin Home App.

Delete the original connection reco时in the app and 陪peat the connection process回．
Check if the bulb is turned o仔． If yes, turn it on and wait until the bulb reconnects with the Wi-Fi network automatically.
Check if there a陪 problems with your internet connection. if necessary，，陪臼t your Wi-Fi router and try again

Home network is 5GHz

The wall penetration capability of 5.0GHz is wea阳r than 2.4GHz w怕ich me唱ns that the outdoor signal of 5.0GHz is worse 2.4GHz. The用fore, most smart devices support 2.4GHz networks or dual-f1陪quency networ<S of 2.4GHz and 5.0GHz.

.lf you are using a dual-band route「 (2.4GHz and 5GHz frequency share a Wi-Fi account.), youαn connect the device using the AP mode.
0r you can log in to the management page of your router and change the SSI D of the
4GHz and 5GHz networks to di仔·erentiate them

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.