UNIVERSAL ELECTRONICS R32068BD00 Remote Control User Guide
- June 5, 2024
- Universal Electronics
Table of Contents
UNIVERSAL ELECTRONICS R32068BD00 Remote Control
Getting Started
Insert 2 AA batteries. Match the + and – marks.
Note: Make sure TV is ON before starting remote control setup.
Tip: The LED will blink 5 times with each key-press when batteries need
replacement
Setup Method A:
- Press and hold SETUP until LED blinks twice.
- Press the TV POWER key, LED remains ON.
- Press and hold down the DIGIT key for your TV brand.
- Let go of the key when your TV turns Setup is complete
Tip: If your brand does not appear on popular TV brand chart, try either Method B or Method C to setup the remote to control your TV.
Functional Key Chart
INDUSTRY CANADA USER’S STATMENET FOR NON- DETACHABLE ANTENNAS FOR BOTH
ENGLISH AND FRENCH
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
design ed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interfer ence wll not occur in a
particular installation. If this equipment does cause harmful interterence to
radio or television reception, the user is encouraged or try to correct the
interference by one or more of the following measures:
- Reorient or relocate the recerving antenna.
- Increase or decrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit d ifferent from that to which the receiver is connected
- Consult the dealer or an experienced remote control/ TV technician for help.
- It is strongly recommended that the TV be plugged into a seperate wall outlet.
This equipment has been verified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
TROUBLESHOOTING
- Problem: LED does not blink when a key is pressed.
- Solution: Replace batteries.
- Problem: TVdoes not respond when TV POWER or VOLUME keys are pressed.
- Solution: Program remote control for your TV brand using instructions in Setup Method A, B, or C.
- Problem: Tried all codes for my TV brand and none work.
- Solution: Try CODE SEARCH (Setup Method B) method or go to www.urcsupport.com for additional suppot
Setup Method B:
NOTE: Make sure TV is ON before starting remote control setup.
- Press and hold SETUP until LED blinks twice.
- Press and hold down the OK/SELECT key.
- Let go of the OK/SELECT key when the TV turns.
Setup Method C:
Note: Make sure TV is ON before starting remote control setup
- Press and hold SETUP until LED blinks twice.
- Enter the 1st TV code for your brand from the code list to the right. LED blinks twice.
- Press the TV POWER key to test TV control. If the TV turns , setup is complete.
- If TV does not turn , repeat this process using the next code for your Tbrand.
Set volume control for the TV:
- Press and hold SETUP for 3 seconds. The LED will blink twice.
- Press VOL +. The LED will blink twice as conrmation
Set volume control for the DTA:
- Press and hold SETUP for 3 seconds. The LED will blink twice.
- Press MUTE. The LED will blink 4 times.
Codes: TV
To find the exact code for your TV, use our
CODE FINDER feature at WWW.URCSUPPORT.COM
Tip: Write the working TV code here for future use.