SANCORP by WHALL EV-691H Battery Cyclone Vacuum Cleaner Instruction Manual

SANCORP by WHALL EV-691H Battery Cyclone Vacuum Cleaner Instruction Manual

Dear Customer

We congratulate you on the purchase of this practical cordless cyclonic vacuum cleaner, which thanks to the 2 in 1 nozzle, the floor nozzle and the suction pipe, allows you to vacuum even hard-to-reach places easily and wireless.

Please read these operating instructions carefully before installation and commissioning in order to familiarize yourself with your new device and to achieve maximum operational safety. In particular, the safety regulations must be observed to avoid accidents and damage. We recommend that you keep the instructions carefully for future reference.

IMPORTANT SAFETY INSTRUCTIONS

In order to avoid injuries caused by electricity such as electric shock, short circuit or fire, we ask you to always observe the following safety regulations:

• Make sure that you never touch the live parts! Electric shock can result in serious injury or even death.
• Only connect the charger to an AC outlet with a voltage of 230 V / 50 Hz. The minimum fuse protection for the socket is 6 amps. The socket should be secured with a residual current circuit. Please be sure to observe the applicable local ordinances and regulations.
• The device must never be operated without supervision, charged or used for other purposes. Use only the accessories supplied with this vacuum cleaner.
• Never use this device to vacuum water, liquids, flammable or explosive substances or materials, burning or hot ashes, matches, cigars or dust or substances harmful to health.
• Never powder-like substances such as Soak in flour. Danger of engine damage!
• Never pick up pointed or sharp objects, e.g. Nails, needles etc.
• Never cover the device while it is in operation.
• Never store or place the device near heat sources such as an oven, stove, heating or heat-emitting devices. Never use the device in potentially explosive areas. Protect the battery from heat and use and store at temperatures between 0°- 40°C.
• Never place the device near bathtubs, swimming pools or containers filled with water where there is a risk of it falling into the water. Electric shock!
• Never immerse the vacuum cleaner or charger in water!
• Only clean the device with a dry cloth.
• Do not use or store the device outdoors. Never expose the vacuum cleaner or battery to moisture or rain or bring it into contact with water. Never vacuum wet surfaces. The device should not be exposed to the sun for long periods. Always fully charge the battery before using it for the first time or after a long period of non-use. If you do not want to use the device for a long time, the battery must still be charged every 3 months (see note “Periodic charging of the battery”).
• When the battery is fully charged, the mains plug of the charger / mains adapter must be pulled out of the socket.
• The device is not designed for commercial use.
• Set up the device in a safe environment so that it cannot be knocked over or tip over. The surface should be flat and dry. Special care is required when using the device on stairs.
• Electrical devices are not toys for children. Never leave the vacuum cleaner unattended when children are around, or place it out of the reach of children. Children should never be allowed to play with the packaging material either, there is a risk of suffocation from plastic bags!
• Always keep the cyclone suction device, battery and charger away from children under 8 years of age.
• Persons with limited physical, sensory or mental abilities as well as children over 8 years of age or ignorant and inexperienced persons are not allowed to use the vacuum cleaner unless they are supervised by a person responsible for their safety or instructed by them exactly how to use the device.
• Children under 8 years of age are not allowed to use the vacuum cleaner.
• Persons under the influence of alcohol and medication must not use the device.
• Power supplies must never be plugged in or unplugged with wet hands. The device must never be used with wet or damp hands. Never pull on the cable to disconnect the charger from the mains, but always on the mains plug.
• Only use the device with the supplied battery, a different battery could damage the device or injure you.
• Only charge the device with the supplied charger / mains adapter.
• Never throw or stab the battery.
• Never remove or insert the battery with wet hands.
• Never use the device while it is being charged.
• Always bring the device to your point of sale for repairs and only use original spare parts. Never remove permanently installed covers or carry out repairs yourself! Danger of electrical shock!
• Use the device only with a faultless charger power cord and plug and protect it from moisture. If the device is not working properly, is damaged or has become wet, do not operate it under any circumstances and have it checked by your sales office. This also applies to the nozzle, brush and suction pipe.
• Do not insert anything into the device openings. Never cover air openings. Do not use the device if the nozzles, pipe or air intake are blocked. Always remove the blockage before switching the device on again.
• Keep suction openings and nozzles or brushes away from the face and body, as well as from hair, jewelry and clothing.
• Only use the device with a dry and correctly installed cyclone insert and HEPA filter as well as the dust container.
• If you attach or remove accessories, the device must be disconnected from the charging station.
• Improper repairs or handling can result in considerable risks for the user and the environment. We accept no liability for damage caused by incorrect use, non-compliance with local safety regulations, or use other than that specified in this manual.

Description of the device

1. Suction power button
2. ON/OFF button
3. Motor unit
4. Release button for suction pipe or Nozzle / brush in manual suction mode
5. Suction pipe
6. Release button for floor nozzle (or nozzle / brush if mounted on the suction pipe)
7. Electric floor nozzle
8. Dust containers
9. Battery charge status indicator
10. Open button the dust container flap
11. HEPA filter and cyclone insert
12. 2 in 1 crevice nozzle
13. Battery
14. Release button to remove the battery
15. Screws for wall bracket
16. Charger (mains adapter)
17. Wall bracket
18. Stretchable hose
19. Cleaning brush
20. Fluff roller brush
21. Crevice tool

Note on the 2 in 1 crevice nozzle

• As a nozzle without a brush, ideal for vacuuming sofa cracks, corners, stairs, etc.
• Ideal as a nozzle with a brush for vacuuming furniture, bookshelves, smooth surfaces.

SPECIAL SAFETY INSTRUCTIONS FOR YOUR CYCLE CLEANER

• Keep the device away from heaters, fire or flames or cigarettes.

• If the air intake opening is blocked or the suction pipe or a nozzle or brush is blocked, you must switch the vacuum cleaner off immediately with the ON / OFF button.
  Remove the reason for the blockage before you switch the device on again.

• Do not vacuum up large or pointed objects. Therefore, you should remove these objects from the floor before vacuuming. Do not vacuum any flammable or burning / glowing substances (e.g. cigarette ends) or liquids.

• Only operate the vacuum cleaner with the correctly installed cyclone insert and HEPA filter.

• Empty the dust container regularly.

• Charge the battery every 3 months, even if the device has not been put into operation, to protect against deep discharge (see note “Periodic charging of the battery”).

INSTALL THE WALL SUSPENSION

1. Screw the wall bracket (17) with the screws at a suitable height on the wall, it should be installed near an electrical outlet.
2. The device’s suspension device is located on the rear of the motor handle.
3. Hang the cyclone suction device on the hanging device on the wall mounting.

ASSEMBLY OF THE VACUUM CLEANER

1. Insert the filter in the dust container

2. Place the cyclone insert in the dust container. Align the pins in the cyclone insert with the cutouts in the dust container.

3. Place the HEPA filter in the cyclone insert.
   

4. Install the dust container in the motor unit

5. Place the dust container on the pins at the bottom of the motor unit.

6. Push the dust container inwards so that it clicks into place.

7. Attach the battery to the motor unit Snap the battery into the battery compartment and then push it into the motor unit until you hear a click.
   

8. Mount the suction pipe and floor nozzle on the motor unit

9. Push the floor nozzle into the lower opening of the suction pipe until it clicks into place.

10. Press the suction pipe into the connection opening of the motor unit until it clicks into place.
    
    Note: You can also insert the floor nozzle directly into the connection opening of the motor unit until it clicks into place.

11.  Remove suction pipe and floor nozzle

12. To disconnect the intake manifold from the motor unit: press the upper release button (4).

13. To remove the floor nozzle from the suction pipe: press the lower unlocking button (6).

14. Mount the 2 in 1 nozzle on the device

15. Cyclone vacuum cleaner as a hand vacuum cleaner use: 2 in 1 nozzle directly into the Connection opening of the motor unit until it clicks in with one click engaged.

16. Use a 2 in 1 nozzle with a suction pipe: Insert the nozzle into the lower opening of the suction pipe until it clicks into place. This variant is ideal for vacuuming ceilings or narrow stairs. To remove, press the release button and remove the nozzle.
    

17. Mount the stretchable hose on the device.

18. Connect the stretchable hose wiith the crevice tool until the buckle is locked.

19. Connect the other end of the stretchable hose to the main body of the vacuum cleaner.
    Please note that there is no buckle here and you need to push it hard until connect.

20. To remove, press the release button and remove the stretchable hose and crevice tool.
    

CHARGE THE BATTERY

1. STEP 1: Use only the supplied AC adapter as a charger for the battery. Hang the assembled vacuum cleaner on the wall mounting, the battery is in the motor unit.
2. STEP 2: Insert the charger plug into the device socket. Insert the charger plug into an electrical outlet. The top light of the battery indicator flashes during charging. Charge the battery with the charger for 4 – 5 hours before using the vacuum cleaner. Warning: Always keep the battery and charger dry. For charging, the battery must always be in the device, never removed.
3. STEP 3: As soon as four bars light up in the charging status display (9), the battery is fully charged and the device can be put into operation.

ATTENTION: Do not leave the cyclone vacuum permanently connected to the charger! Pull out the power plug from the socket when all four bars light up. This saves energy and extends the life of your device. As soon as the suction power drops, charge the device immediately.

IMPORTANT: PERIODIC CHARGING OF THE BATTERY

To prevent deep discharge, the battery must be charged every 3 months even when not in use. Failure to follow this procedure will void the warranty on the battery. Our technical service can determine whether a battery is deeply discharged.

INSTALLATION

• Charge the battery with the charger until four bars light up in the charging status display. lf you charge at a low battery state,lt will take 4-5 hours to fill Always fully charge the device before using it for the fi rst time and after a long period of non-use. Then pull out the mains plug.
• If the cyclone insert with HEPA filter is in the motor unit and installed together with the dust container, you can start up the vacuum cleaner.
• Mount the suction pipe or the appropriate nozzle or brush as described.
• Press the ON / OFF button (2) to switch on the vacuum cleaner.
• With the suction power button (1) you can set the suction power: high or low.
• If you want to change the nozzles or brushes, always switch off the device with the ON / OFF button.

EMPTY DUST CONTAINER

• When the dust container is full, you should empty it to maintain full suction power.
• The device must be switched off beforehand and the battery removed from the motor unit (press the release button (14) before emptying the dust container.

1. Turn the dust container to separate it from the motor unit.
2. Hold the flap of the dust container over a waste bin and press the button (10) to open the flap. Empty dust and dirt.
3. Close the flap again so that it clicks into place. Put the empty dust container back into the device.

CLEANING THE DUST CONTAINER, THE CYCLONE INSERT AND THE FILTER

From time to time you should remove and clean the dust container and the cyclone insert with HEPA filter, at the latest when you notice that the suction power is deteriorating. Switch off the device with the ON / OFF button and remove the battery.

1. Turn the dust container (8) and remove it from the device. Empty it as described in the chapter “Emptying the dust container”.
2. Take the cyclone insert and the HEPA filter out of the dust container.
3. Knock out the cyclone insert and the HEPA filter or clean them with a brush.
4. You can also clean the cyclone insert and the HEPA filter under lukewarm water. Allow both to air dry completely before reinstalling them.
5. Rinse the dust container under lukewarm water, dry it with a soft cloth and then let it air dry completely.
6. Then put all the parts back into the device and close the flap so that it engages.

Attention: The device may only be put into operation if the dry cyclone insert and HEPA filter are correctly inserted again and the dust container is inserted.

CLEANING THE VACUUM CLEANER

• When the device is switched off and disconnected from the charger, you can wipe the device with a dry cloth.
• Do not use abrasive rags, steel wool, abrasive cleaners, acetone or alcohol.
• Never immerse the vacuum cleaner in water.
• Store the device in a dry, cool place out of the reach of children.

CLEAN THE ELECTRIC FLOOR NOZZLE

Hair and lint can get caught in the brush, which must be removed from time to time so that the suction power does not deteriorate.

Problem Solving

PROBLEM| POSSIBLE CAUSE|

PROBLEM SOLVING

---|---|---
Vacuum cleaner doesn’t work. / Vacuum cleaner cannot be switched on.|

• The battery is empty.
• The battery is being charged.

|

• Charge the battery with the charger.
• Disconnect the device from the charger as soon as the charging process is complete.

Suction power is low or nonexistent.|

• The dust container is full.
• The cyclone insert and filter must be cleaned.
• The air intake is blocked.
• The battery is weak.

|

• Empty the dust container.
• Clean the cyclone insert and filter and insert correctly.
• Check air intake for possible blockage and remove blockage.
• Charge the battery with the charger.

Dust escapes from the device.|

• The dust container is full.
• Cyclone insert and filter are not inserted correctly.

|

• Empty the dust container.
• Insert the cyclone insert and filter correctly.

Battery does not charge.|

• The battery needs to be replaced.

|

• Contact your point of sale.

Unusual noises while sucking.|

• The dust container is full.
• Floor nozzle blocked by hair and lint.

|

• Empty the dust container.
• Remove and clean the floor nozzle.

DISPOSAL AND GUARANTEE

DISPOSAL

Disused devices must be made unusable and must not be disposed of with household waste. Please take your device to the next collection of recyclables, so that recyclable material is reused and your device is disposed of in an environmentally friendly way.

DISPOSAL OF THE BATTERY

• This lithium-ion battery uses the latest technology and will serve you well for several years. However, since lithium-ion batteries also contain substances that are dangerous for the environment, they must not be disposed of with normal household waste.
• Before you dispose of the cyclone vacuum, remove the battery, glue the battery ends with a firm adhesive tape and take the battery to a collection of valuable materials so that it can be recycled or disposed of in an environmentally friendly manner.

GUARANTEE

• The device has a one-year guarantee from the date of sale. (Keep the invoice!)
• Damages resulting from incorrect use are not covered by the guarantee.

TECHNICAL SPECIFICATIONS

Model

| EV-691H
---|---
Power|

250W

Suction

| 6kPa / 10kPa /2 2 kPa
Working time|

14 -53 mins

Adapter input

| AC100-240V 50/60Hz
Adapter output|

35V500mA

Battery type

| Lithium battery pack
Battery capacity|

2200mAh

Charging time

| 4 – 5 hours
Dust cup capacity|

500 ml

Net weight

| 2.97 kg
Gross weight|

4.3 kg

CUSTOMER SUPPORT

Company: Qingdao Weizhisheng Information Technology Co., Ltd. Address: Room 7079, Huayang Road 54#,Shibei district,Qingdao,China
Email: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>