BYEASY P6000 Wireless Laser Presenter User Manual
- June 6, 2024
- BYEASY
Table of Contents
P6000 Wireless Laser Presenter
User Manual
Functions Front View
-
Ext Playback mode (ESC)
(While pressing on the Page up and Page down together for about 1 second) -
Switchable compatible with Windows and Mac operating systems,
(While holding down the Page up and Page down for about 3 seconds to switch operating systems )
Functions Back View
Features
- Adopt2.4HGz wireless technology and high brightness green laser light design
- Page Up, Page Down,Keys Pla(SHIFT4F5),Screen black 8 Exit Playback mode(ESC).
- Switchable compatible with Windows and Mac operating systems. (While holding down the Page up and Page down for about 33 seconds to switch operating systems)
- Green laser light can be used continuously for 50 hours without a replacement battery
- Low voltage indicator reminds battery replacement.
- With the power switch, battery more power,
- Magnetic suction accommodating USB wireless receiver
- USB 2.0 connection, plug & play.
- No software downloads & driver installation are required.
Specifications
-
Dimension >
Presenter Le15.8 cm We1.9 cm He1.9 cm
Receiver > L= 1.9cm W= 1.3cm H=0.45cm
Receiver : 2Zg -
Weight : Presenter : 46g(battery included)
-
Button> 4 buttons
-
Presenter Power : 3.0V
-
RF Feauency : 2.408-2,474GHz
-
OutPut :CLIM < 1mW
-
POWER: DC 3V–30-50m4
-
Laser Wavelength > 650nm
-
Operating distance : 30 M
-
Interface : USB2.0
-
Support OS : Win 8.1/7/Vista/XP /MAC 10.7 Up
WAININMG
LASER RADIATION AVOID DIRECT EYE EXPOSURE
System Requerment
The wireless USB receiver is used as a regular USB flash drive. Plug the
receiver directly into an available USB port of your notebook or computer. the
drive is automatically recognized and installed. “ Note: Please always pay
attention to the direction of the USB when plugging into the USB drive
Pairing step
- Take out the battery cover of the presenter and put in 2 AM batteries properly. ( please don’t turn on the power at the side of the presenter at this moment )
- At the same time suppress the Page UP and Page Down button after turning the power switch The indicator light will flash ( can suppress the release button ) Page UP and Page Down
- The USB receiver into your computer’s USB port, the computer will automatically recognize the hardware and install the USB drivers on their own Indicator will stop flashing, indicating that the connection has been successful, you can use.
Note
- Make sure the battery is charged, if not replace the battery, Please brief the distance of the USB pen and receiver
- pairing control within 30 cm And complete the pairing steps within 30 seconds
Batter and related information
- 1.5V (MA) size alkaline, carbon-zinc or zinc battery filter
- Insert the batteries, please check the battery’s positive (+) negative (-) pole and the direction of the battery slot of the marked line
- Charge or replace the batteries after power is drained. Please remove the batteries to avoid leakage that might cause harm.
- Remove the batteries if the device won’t be used for a long time.
- Dispose of the used batteries properly.
- In case of battery leakage and accidentally getting skin contact, rinse the affected area immediately with running water.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
FCC ID: 2A4NB-P6000 ****